saw bandpass filter 205101B part no. 205101B features z if bandpass filter z high attenuation z 50 ohms single-ended operation z smd package 13.3mm 6.5mm 1.6mm package dimension rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 1/7 12 11 10 9 8 7 6 5 4 3 2 1 0.800.1 1.500.1 2.540.1 7.620.1 2.540.1 1.610.2 6.500 .2 13.300.2 1 2 3 4 10 9 8 7 5 6 11 12 itf 02d073a 205101B package s1365 pin configuration 11 input 5 output 6, 12 ground 1, 2, 3, 4, 7, 8, 9, 10 case ground dimensions shown are nominal in millimeters body : al 2 o 3 ceramic lid : kovar, ni plated terminations : au pl ating 0.3 ~ 1.0 um, over a 1.27 ~ 8.89 um ni plating maximum ratings parameter unit minimum typical maximum operation temperature range c -10 25 60 storage temperature range c -40 - 85 electrostatics sensitive device ( esd)
saw bandpass filter 205101B part no. 205101B electrical specification fc = 70.0mhz terminating source impedance : 50 and matching network terminating load impedance : 50 and matching network minimum typical maximum center frequency at room temp. mhz 69.955 70.0 70.044 insertion loss db - 5.0 6.0 3db bandwidth mhz 0.030 0.035 - 40db bandwidth mhz - 0.170 0.200 absolute group delay at fc usec - 15 - group delay variation at 3db usec - 5 - relative attenuation 0.3 mhz ? 69.8 mhz 70.2 mhz ? 71.0 mhz 71.0 mhz ? 75.0 mhz db 50 35 50 55 40 55 - temperature coefficient of frequency ppm/c 2 - -0.03 - notes : 1) all specifications are based on th e matching schematic shown below, measur ed by agilent network analyzer and full 2 port calibration. 2) all attenuation measurements are measured relative to insertion loss rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 2/7
saw bandpass filter 205101B part no. 205101B matching schematic ( actual matching values may vary due to pcb layout and parasitics ) l2 l1 c2 c1 output 50 input 50 l1, l2 = 680 nh c1, c2 = 0.5 pf marking configuration itf 1) 02d073 2) a 3) 205101B 4) 1) manufacturer name 2) lot number 3) group name ( **refer to the next page ) 4) part number rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 3/7
saw bandpass filter 205101B part no. 205101B rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 4/7 marking example center frequency range ( mhz) at room temp. marking itf 02d073 a 69.955~69.964 205101B itf 02d073 b 69.965~69.974 205101B itf 02d073 c 69.975~69.984 205101B itf 02d073 d 69.985~69.994 205101B itf 02d073 e 69.995~70.004 205101B itf 02d073 f 70.005~70.014 205101B itf 02d073 g 70.015~70.024 205101B itf 02d073 h 70.025~70.034 205101B itf 02d073 i 70.035~70.044 205101B
saw bandpass filter 205101B part no. 205101B typical performance (at +25 ) ch1 s 21 log mag 10 db/ ref 0 db center 70.000 000 mhz span 1.000 000 mhz cor prm ch2 s 21 log mag ref 0 db 1 db/ cor prm 1 1 2 3 4 1_: 0 db 0.000 000 mhz ref=1 bw: .160 066 mhz cent: 69.991714 mhz q: 437.27 1_ loss: -5.0688 db 2 1 2 3 4 1_ 0 db 0.000 000 mhz ref=1 bw: .034 918 mhz cent: 69.999467 mhz q: 2004.7 1_ loss: -5.0282 db rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 5/7 ch1 s 21 log mag 10 db/ ref 0 db center 70.000 000 mhz span 4.000 000 mhz cor prm
saw bandpass filter 205101B part no. 205101B packing specification 1. reeling quantity : 2000 pcs / reel 2. taping structure : the tape shall be wound ar ound the reel in the direction shown below. reel top cover tape carrier tape tape specification 1. leader part and vacant position specification end start tape running direction vacant 150mm min. component contained vacant 150mm min. leader part 250mm min. 2. tensile strength of carrier tape 4.4n/mm width 0~15 degree top cover tape direction of pull carrier tape 3. top cover tape adhesion 1) pull off angle : 0~15 2) speed : 300mm/min 3) force : 20~70g rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 6/7
saw bandpass filter 205101B part no. 205101B carrier tape dimensions [unit : mm] a 7.00 0.1 b 13.80 0.1 c 13.25 0.1 d 1.95 0.1 e 24.00 0.1 f 12.00 0.1 rev. date 2004-07-14 i t f co., ltd. 102-901, bucheon technopark 364, samjeong-dong, ojeong-gu, bucheon-city, gyounggi-do, korea 421-809 rev. nr3006-as32 7/7 part direction tape running direction reel dimensions [unit : mm] g = 2g = 24.4 mm
|
