differential lvpecl crystal clock oscillators hpk5361 series 200 fsec jitter +2.5v +3.3v ?k ? family mercury since 1973 mercury www.mercury-crystal.com taiwan: tel (886)-2-2406-2779, fax (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com u.s.a.: tel (1)-909-466-0427, fax (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com mercury page 1 of 4 date: january 24, 2011 rev. 0 ? femto second integrated phase jitter (200 fs typical, 12 khz to 20 mhz) ? superior phase noise (-138 dbc/hz at 10 khz and -144 dbc/hz at 100 khz offset). ? high performance with surprisingly low price. ? 2.5v or 3.3v supply voltage. general specifications product series hpk5361; ? k ? family characteristics. tri-state on pad 1 frequency range 40 mhz ~ 200 mhz. output logic differential pecl square wave frequency stability vs operating temperature range stability code commercial ? c ?: : -10c to +70c industrial ? i ?: -40c to +85c 25 ppm a d 50 ppm b e 100 ppm c f custom xx ppm c xx i xx if custom, use ?temperature range code + desired stability in ppm? for the stability code. example: ? c20 ? (20 ppm over -10 to +70c). supply voltage v cc +2.5 v 5 % (voltage code is ? 25 ?); or +3.3 v 5 % (voltage code is ? 3 ?) output voltage high ?1?, v oh v dd -1.025 v min.; v dd -0.95 v typical; v dd -0.88 v max. condition: 50 ohms to v dd -2v output voltage low ?0?, v ol v dd -1.810 v min.; v dd -1.70 v typical; v dd -1.62 v max. condition: 50 ohms to v dd -2v output swing 595 mv min; 750 mv typical; 930 mv max. current consumption 35 ma typical; 50 ma max. load 50 ohms into v cc -2v or thevenin equivalent (terminating resistors required on all outputs). rise time (tr) 0.3 n sec. typ; 0.5 n sec. max. 20% ? 80% of waveform fall time (tf) 0.3 n sec. typ; 0.5 n sec. max. 80% ? 20% of waveform duty cycle 50% 5% max. measured at 50% waveform tri-state function on pad no. 1 if no connection or v dd *70% min is applied: output. internal pull-up oscillation disable time is 0.2 u sec max. if v dd *30% max is applied: high impedance. current consumption is 10 ua typical oscillation enable time is 2 m sec. max. phase jitter (rms) 200 fs typical (12 khz to 20 mhz integrated) ssb phase noise (dbc/hz). typical offset 10 hz 100 hz 1 khz 10 khz 100 khz 1 mhz 10 mhz 125 mhz -50 -82 -116 -138 -144 -149 -155 start-up time 3 ms typical; 10 m sec. max. aging 3 ppm / year max. packaging 180 mm reel; 16 mm tape, 7.8 mm pitch. 1000 pcs per reel. (1) inclusive of 25c tolerance, operating temperature range, 10% input voltage variation, load change, aging at +25c, shock and vibration www.datasheet.net/ datasheet pdf - http://www..co.kr/
differential lvpecl crystal clock oscillators hpk5361 series 200 fsec jitte r +2.5v +3.3v ?k? family mercury since 1973 mercury page 2 of 4 date: january 24, 2011 rev. 0 absolute maximum rating permanent damage may be created if operate beyond limits specified ta=25 c, vss=0v parameters rating min. max. supply voltage vss-0.5v 5.0v input voltage vss-0.5v v dd +0.5v output voltage vss-0.5v v dd +0.5v environmental performance specifications green requirement rohs 6/6 (2002/95/ec) and weee (2002/96/ec) compliant msl level level 1 per ipc/jedec j-std-020d.1 storage temp. range -55c to +125c humidity 85% rh, 85c, 48 hours hermetic seal leak rate 2x10 -8 atm-cm 3 /sec max. solderability mil-std-202f method 208e reflow 260c for 10 sec max.. 2 times max. vibration mil-std-202f method 204, 35g, 50 to 2000 hz shock mil-std-202f method 213b, test condi. e, 1000gg ? sine wave esd protection 2kv max. human body model. contact pad surface finish gold (0.3~1.0 um) on nickel (1.27~8.89 um) weight per unit 160 mg typical part number format and examples : example : 3hpk5361-a-155.520; 25hpk5361-a-155.520 explanation : +3.3v hpk5361 series lvpecl output clock o scillator, frequency stability is 25 ppm over -10c to +70c, 155.520 mhz " " " : customer to specify 3 hpk5361 ? a ? 155.520 c d e f c : v dd voltage codes: ? 3 ? for +3.3 v; ? 25 ? for +2.5 v d : hpk5361 product series. ? h ? for clock; ? p ? for pecl; ? k ?: for ?k? family characteristics.? 536 ? for 3.2x5 mm smd with 6 pads. ? 1 ? for tri-state on pad 1. e : frequency stability code: ? a ? ~ ? f ? or custom. see table above. f : frequency in mhz 25hpk5361 and 3hpk5361 test circuit and waveform: + - 0.1uf v a supply voltage pecl - + top view r4 1.30 v pecl dd 50 ohm s 20% 80% pecl pecl 50% tr tf duty cycle 45% ~ 55% 45% ~ 55% duty cycle r3 1.30 v 50 ohm s +v dd +v v dd r1,r3 r2,r4 +3.3v 127 82.5 +2.5v 250 62.5 r2 r1 1 2 3 6 5 4 m e c hpk5361 hpk5361 package dimensions and recommended solder pad layout : unit mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
differential lvpecl crys tal clock oscillators hpk5361 series 200 fsec jitter +2.5v +3.3v ?k? family mercury since 1973 mercury page 4 of 4 date: january 24, 2011 rev. 0 5.00? .15 3.20? .15 1.20? .1 2.54 typ. 1.2? .1 m e c 4 6 1 3 pad 1 pad 2 pad 3 pad 4 tri- state ground output bottom view 1 3 6 4 rounded pad is pad no. 1. count counter- clockwise when looking at top view. count clockwise when looking at bottom view. hpk5361 2 5 0.10 typ. 2 5 supply voltage pad 5 pad 6 0.64 typ. 0.50 typ. 0.84 1.2 1.0 25.4 no connection output typical phase noise plot 3hpk5361-a-125.000 www.datasheet.net/ datasheet pdf - http://www..co.kr/
differential lvpecl crys tal clock oscillators hpk5361 series 200 fsec jitter +2.5v +3.3v ?k? family mercury since 1973 mercury page 4 of 4 date: january 24, 2011 rev. 0 hpk5361 recommended solder reflow profile (from ipc/jedec j-std-020d.1) profile feature sn-pb eutectic assembly pb-free assembly preheat/soak - temperature min. (ts min.) - temperature max. (ts max.) - time (ts) (ts min. to ts max.) 100 ? c 150 ? c 60 to 120 seconds 150 ? c 200 ? c 60 to 180 seconds ramp-up rate (t l to tp) 3 ? c / sec. max. 3 ? c / sec. max. liquidous temperature (t l ) time (t l ) maintained above t l 183 ? c 60 to 150 seconds 217 ? c 60 to 150 seconds peak package body temperature (tp) 235 ? c 260 ? c time (tp) within 5 ? c of the classification temperature tc 10 to 30 seconds 20 to 40 seconds ramp-down rate (tp to t l ) 6 ? c / second max. 6 ? c / second max. time 25 ? c to peak temperature 6 minutes max. 8 minutes max. all temperatures refer to topside of the package, measured on the package body surface. www.datasheet.net/ datasheet pdf - http://www..co.kr/
|
