MN103S53G data ram ( 32-bit) 12 k-byte command rom ( 64-bit) 128 k-byte type MN103S53G (under development) package lqfp80-p-1414a *pb-free minimum instruction execution time 25.0 ns (at 3.0 v to 3.6 v, 40 mhz) interrupts ? reset irq 8 nmi timer 28 sif 10 i 2 c 2 dma 6 wdt a/d system error timer counter 8-bit timer 10 reload-down count cascade connection possible (usable as a 16-bit to 32-bit timer) 16-bit timer 6 up-down count input capture function pwm generating function compare/capture register 2-ch. watchdog timer 1 maf00012aem dma controller number of channels: 2 unit of transfer: 8/16/32 bits max. transfer cycles: 65535 staring factor: external interrupt, timer factor, serial transmission/reception factor, i 2 c transmission/reception factor, external transmission request factor, a/d conversion finish, software factor transfer method: 2-bus cycle transfer adressing modes: fixed, increment, decrement transfer modes: word transfer, burst transfer, intermittent transfer serial interface uart/synchronous/multi-master i 2 c interface selective: 2 uart/synchronous interface selective: 3 i/o pins 58 common use i/o a/d inputs 10-bit 8-ch. electrical characteristics t.b.d.
MN103S53G pin assignment maf00012aem type mn103sf53g (under development) command rom ( 64-bit) 128 k-byte data ram ( 32-bit) 12 k-byte minimum instruction execution time 25.0 ns (at 3.0 v to 3.6 v, 40 mhz) package lqfp80-p-1414a *pb-free support tool flash memory built-in type in-circuit emulator px-ice103s53 on-board development tools px-odb103s-o lqfp80-p-1414a *pb-free 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 p03/irq2/dreq0/a19 tm15ioa/p02/a18 tm15iob/p01/a17 p00/a16 vdd ki7/p17/adm15 ki6/p16/adm14 ki5/p15/adm13 ki4/p14/adm12 ki3/p13/adm11 ki2/p12/adm10 ki1/p11/ad9 ki0/p10/ad8 vss sbt4/p27/adm7 sbo4/p26/adm6 sbi4/p25/adm5 sbt3/p24/adm4 sbo3/p23/adm3 sbi3/p22/adm2 p51/bg p52/br p53/dk p40/adtrg p41/sbi2 p42/sbo2 p43/sbt2 p30/cs0 irq4/p31/cs1 irq5/p32/cs2 irq6/p33/cs3 vss p34/sysclk vdd vpp/(n.c.*) p35/re tm13ioa/tm6io/p36/we0 tm13iob/tm7io/p37/we1 tm14ioa/tm8io/p20/adm0 tm14iob/tm9io/p21/adm1 p63/an3 p64/an4/irq4 p65/an5/irq5 p66/an6/irq6 p67/an7/irq7 vrefh nmirq vdd exmod0 exmod1 mmod0 mmod1 vss tcpout vdd osci osco vss rst cksel p62/an2 p61/an1 p60/an0 p75/sbt1/tm14iob/tm9io/scl1 p74/sbo1/tm14ioa/tm8io/sda1 p73/sbi1/tm13iob/tm7io p72/sbt0/tm13ioa/tm6io/scl0 p71/sbo0/tm12iob/tm5io/sda0 p70/sbi0/tm12ioa/tm4io vdd p85/tm11iob p84/tm11ioa p83/tm10iob p82/tm10ioa vss p81/irq1 p80/irq0 p92/as p91/rwsel p90/irq3/dreq1 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 MN103S53G
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general elec- tronic equipment (such as office equipment, communications equipment, measuring instruments and house- hold appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus- tion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifica- tions satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rat- ing, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
