View AWU6616P9_5325952.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

awu6616 help3e tm dual-band 1 & 5, 6 cdma/wcdma 3.4 v linear power amplifer module data sheet - rev 2.3 m47 package 14 pin 3 mm x 5 mm x 1 mm surface mount module features ? ingap hbt technology ? high effciency (r99): ? 37 % @ p out = +28.1 dbm (band 1) ? 38 % @ p out = +28.7 dbm (band 5, 6) ? 24 % @ p out = +16.5 dbm ? 8.5 % @ p out = +8 dbm ? low quiescent current: 4 ma ? internal v oltage regulation ? built-in directional coupler ? common v mode control line ? simplifed v cc bus pcb routing ? reduced external component count ? low profle surface mount package: 1 mm ? rohs compliant package, 260 o c msl-3 applications ? band 1 +5, 6 dual-band wcdma/hsp a wireless devices ? band class 0+6 dual-band cdma/evdo wireless devices. ? band class 0+6 dual-band evdo rev. b wireless devices. product description awu6616 addresses the demand for increased integration in dual-band handsets for wcdma and cdma networks. the small footprint 3 mm x 5 mm x 1 mm surface- mount rohs compliant package contains independent rf pa paths to ensure optimal performance in both frequency bands, while achieving a 25% pcb space savings compared with solutions requiring two single-band pas. the package pinout was chosen to enable handset manufacturers to easily route bias to both power amplifers and simplify control with common mode pins. the device is manufactured on an advanced ingap hbt mmic technology offering state-of-the-art reliability, temperature stability, and ruggedness. the awu6616 is part of anadigics high-effciency-at-low-power (help?) family of wcdma power amplifers, which deliver low quiescent currents and signifcantly greater effciency without the need of an external dc-dc converter. through selectable bias modes, the awu6616 achieves optimal effciency, specifcally at low- and mid-range power levels where the pa typically operates, thereby dramatically increasing handset talk-time. its built-in voltage regulator eliminates the need for external switches. this pa has built-in directional couplers for each band, with a common coupler output port cpl_out. these couplers provide high directivity and 23 db coupling. the 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, effciency and linearity in a 50 ? system. figure 1: block diagram v en_800 v batt rf in_800 rf out_800 v cc a v mode1 1 13 11 14 12 3 4 2 gnd v cc 5 6 10 9 bias control voltage regulation cpl out rf out_imt v en_imt rf in_imt gnd at slug (pad) 8 7 v mode2 gnd bias control voltage regulation cpl cpl awu6616 02/2012 obsolete
2 table 1: pin description figure 2: pinout v mode1 v mode2 cpl out v en_800 rf in_800 rf in_imt v en_imt rf out_800 rf out_imt pin name description 1 v en_800 enable voltage for cell & jcell band 2 rf in_800 rf input for cell & jcell band 3 v mode1 mode control voltage for cell & jcell & imt bands 4 v batt battery voltage 5 v mode2 mode control voltage for cell & jcell & imt band 6 rf in_imt rf input for imt band 7 v e n_imt enable voltage for imt band 8 rf out_imt rf output for imt band 9 gnd ground 10 cpl out coupler output port 11 v cc a battery voltage a 12 v cc supply voltage 13 rf out_800 rf output for cell & jcell band 14 gnd ground data sheet - rev 2.3 02/2012 awu6616 obsolete
3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operation at v cc = +3.2 v, p out is derated by 0.5 db. parameter min max unit supply voltage (v batt , v cc , v cc a) 0 +5 v mode control voltage (v mode1, v mode2 ) 0 +3.5 v enable voltage (v en_cell , v en_pcs ) 0 +3.5 v rf input power (p in ) - +10 dbm storage temperature (t stg ) -40 +150 c parameter min typ max unit comments operating frequency (f) 824 1920 - 849 1980 mhz umts band 5, 6, cdma bc 0 umts band 1, cdma bc 6 supply voltage (v cc and v batt ) +3.2 +3.4 +4.2 v enable voltage (v en ) +1.35 0 +1.8 - +3.1 +0.5 v pa "on" pa "shut down" mode control voltage (v mode1, v mode2 ) +1.35 0 +1.8 - +3.1 +0.5 v low bias mode high bias mode rf output power, band 5, 6 umts r99 wcdma, hpm hspa (mpr = 0 db), hpm r99 wcdma, mpm hspa (mpr = 0 db), mpm r99 wcdma, lpm hspa (mpr = 0 db), lpm 28.0 (1) 27.0 (1) 16.5 (1) 15.5 (1) 8.0 (1) 7.0 (1) 28.7 27.7 16.6 15.6 8.0 7.0 - - - - - - dbm 3gpp ts 34.121-1, rel8 table c.11.1.3 subtest 1 rf output power, band class 0 cdma2000, hpm cdma2000, mpm cdma2000, lpm 27.0 - - 27.8 16.0 7.5 - - - dbm cdma2000 rc-1 rf output power, band 1, umts r99 wcdma, hpm hspa (mpr = 0 db), hpm r99 wcdma, mpm hspa (mpr = 0 db), mpm r99 wcdma, lpm hspa (mpr = 0 db), lpm 27.6 (1) 26.6 (1) 16.0 (1) 15.0 (1) 8.0 (1) 7.0 (1) 28.1 27.1 16.5 15.5 8.0 7.0 - - - - - - dbm 3gpp ts 34.121-1, rel8 table c.11.1.3 subtest 1 rf output power, band class 6 cdma2000, hpm cdma2000, mpm cdma2000, lpm 27.0 (1) - - 27.5 16.0 7.5 - - - dbm cdma2000 rc-1 case temperature (t c ) -30 - +90 c data sheet - rev 2.3 02/2012 awu6616 obsolete
4 table 4: electrical specifcations - wcdma operation (band 5 & 6) (t c = +25 c, v batt = v cc = +3.4 v, v en_cell = +1.8 v, 50 ? system, r99 uplink waveform) notes: (1) pae and acp limit applies at 836.5 mhz. parameter min typ max unit comments p out v mode1 v mode2 dl 25 14.5 12 14 p p p 1.8 v 1.8 v 1.8 v &/5+2vhw - - - -42 -42 -41 p p p 1.8 v 1.8 v 1.8 v &/5+2vhw - - - -58 -55 -54 -48 -48 -48 p p p 1.8 v 1.8 v 1.8 v 3rhuhllh 34 18 6 38 21 8 - - - p p p 1.8 v 1.8 v 1.8 v 4lhvhw&uuhw,t - 4 ma wur and v cc slv v mode1 = +1.8 v, v mode2 =+1.8 v mode control current - ma wur mode slv mode1 = +1.8 v dwwhu&uuhw - 1.5 3 ma wur pin, v mode1 = +1.8 v, v mode2 = +1.8 v enable current - ma wur 1 pin 1rlvhl5hhlhd - -133 - p+ +wr+ +duprlv r rr - - -38 p out < p ,sw,pshdh - - vswr &rsoldwru - 23 - 6sulrv2wsw/hho doovsulrvrwswv - - -65 p out < p ,ed/rd65 2wred/rd65 ssolhvrhudoorshudwl rlwlrv /rdplvpdwvwuhvvlwr shupdhwhuddwlrrudlouh - - vswr ssolhvrhuoorshudwl rlwlrv data sheet - rev 2.3 02/2012 awu6616 obsolete
5 table 5: electrical specifcations - cdma2000 operation (band class 0) (t c = +25 c, v batt = v cc = +3.4 v, v enable = +1.8 v, 50 ? system, rc-1 waveform) parameter min typ max unit comments p out v mode1 v mode2 dl 24.5 13.5 26.5 16.5 11 14 p p p 1.8 v 1.8 v 1.8 v mdhw&dho3rhu at ? ??? ?????? ????? - - - -51 -51 -51 -46.5 -46.5 -46.5 p p p 1.8 v 1.8 v 1.8 v mdhw&dho3rhu at ?? ??? ?????? ????? - - - -55 -55 -55 p p p 1.8 v 1.8 v 1.8 v 3rhuhllh - - - 35 - - - p p p 1.8 v 1.8 v 1.8 v 6sulrv2wsw/hho doovsulrvrwswv - - p out ? ??? ?????? ?????? ??? ???? ??? - - vswr ssolhvrhudoorshudwl rlwlrv data sheet - rev 2.3 02/2012 awu6616 obsolete
6 table 6: electrical specifcations - wcdma operation (band 1) (t c = +25 c, v batt = v cc = +3.4 v, v en_pcs = +1.8 v, 50 ? system, r99 uplink waveform) notes: (1) acprs and effciency limits at 1950 mhz. parameter min typ max unit comments p out v mode1 v mode2 gain 24 12 7 26.5 14.5 10 30 18 13 db +28.1 dbm +16.5 dbm +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v aclr1 @ 5 mhz offset (1) - - - -41 -41 -43 -37 -36 -36 dbc +28.1 dbm +16.5 dbm +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v aclr2 @ 10 mhz offset (1) - - - -55 -56 -55 -48 -48 -48 dbc +28.1 dbm +16.5 dbm +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v power-added efficiency (1) 33 20 6 37 24 8.5 - - - % +28.1 dbm +16.5 dbm +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v quiescent current (icq) - 4 7 ma through v batt and v cc pins, v mode1 = +1.8 v, v mode2 =+1.8 v mode control current - 0.1 0.2 ma tthrough v mode pins, v mode1 = +1.8 v v mode2 = +1.8 v battery current - 1.4 3 ma through v batt pin, v mode1 = +1.8 v, v mode2 = +1.8 v enable current - 0.15 0.3 ma through v e n_imt pin hbt leakage current on v cc (shutdown mode) - <1 5 e a v batt = +4.2 v, v cc = +4.2 v, v e n_imt = 0 v, v mode1 = 0 v, v mode2 = 0 v total decoder current on v batt (shutdown mode) - 14 22 e a v batt = +4.2 v, v cc = +4.2 v, v e n_imt = 0 v, v mode1 = 0 v, v mode2 = 0 v noise in receive band - -136 -134 dbm/hz 2110 mhz to 2170 mhz harmonics 2fo 3fo, 4fo - - -42 -50 -30 -38 dbc p out < +28.1 dbm input impedance - - 2:1 vswr coupling factor - 23 - db spurious output level (all spurious outputs) - - -65 dbc p out < +28.1 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating conditions load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating conditions data sheet - rev 2.3 02/2012 awu6616 obsolete
7 table 7: electrical specifcations - cdma2000 operation (band class 6) (t c = +25 c, v batt = v cc = +3.4 v, v enable = +1.8 v, 50 ? system, rc-1) parameter min typ max unit comments p out v mode1 v mode2 gain 23 10.5 6 25 13.5 9.5 29 17 13 db +27.5 dbm +16 dbm +7.5 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v adjacent channel power at + 1.25 mhz offset primary channel bw - 1.23 mhz adjacent channel bw = 30 khz - - - -51 -51 -51 -46.5 -46.5 -46.5 dbc +27.5 dbm +16 dbm +7.5 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v adjacent channel power at +1.98 mhz primary channel bw=1.23 mhz adjacent channel bw=30 khz - - - -55 -55 -55 -49 -49 -49 dbc +27.5 dbm +16 dbm +7.5 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v power-added efficiency - - - 33 18 7 - - - % +27.5 dbm +16 dbm +7.5 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v spurious output level (all spurious outputs) - - -70 dbc p out < +27.5 dbm, in-band vswr < 5:1, out-of-band vswr < 10:1. applies to all operating condtions. load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over full operating range data sheet - rev 2.3 02/2012 awu6616 obsolete
8 application information to ensure proper performance, refer to all related application notes on the anadigics web site: http://www.anadigics.com shutdown mode the power amplifer may be placed in a shutdown mode by applying logic low levels (see operating ranges table) to the v enable and v mode voltages. bias modes, medium bias mode the power amplifer may be placed in low bias mode or a high bias mode by applying the appropriate logic level (see operating ranges table) to the v mode1, and v mode2 pins. the bias control table lists the recommended modes of operation for various applications. figure 3: recommended on/off timing sequence v en_800, imt v cc/ v cc a note 1 rf in_800, imt notes 1,2 off sequence referenced after 90% of rise time referenced before 10% of fall time on sequence on sequence start t_ 0n = 0 t_ 0n +1 s t_ 0n +3 s off sequence start t_ 0f f = 0 t_ 0f f+ 2 st _0 ff +3 s vcontrols venable/vmode(s) rise/fall max 1 s defined at 10% to 90% of min/max voltage notes: (1) level might be changed after rf is on. (2) rf off defned as p in -30 dbm. (3) switching simultaneously between v mode and v en is not recommended. data sheet - rev 2.3 02/2012 awu6616 obsolete
9 figure 4: application circuit 1 13 11 14 12 3 4 2 5 6 10 9 bias control voltage regulation cpl out gnd at slug (pad) 8 7 bias control voltage regulation cpl cpl rf in_800 rf in_imt v mode1 v batt v en_800 v en_imt 2.2 ?f v mode2 68pf v cc 68 pf 1000 pf 2.2 ?f rf out_800 33 pf rf out_imt 1000 pf table 8: bias control application p out levels bias mode v en v mode1 v mode2 v cc v b at t wcdma - low power (low bias mode) < +8 dbm low +1.8 v +1.8 v +1.8 v 3.2 - 4.2 v > 3.2 v wcdma- med power (medium bias mode) > 8 dbm ? +16.5 dbm low +1.8 v +1.8 v 0 v 3.2 - 4.2 v > 3.2 v wcdma - high power (high bias mode) > +16.5 dbm high +1.8 v 0 v 0 v 3.2 - 4.2 v > 3.2 v shutdown - shutdown 0 v 0 v 0 v 3.2 - 4.2 v > 3.2 v data sheet - rev 2.3 02/2012 awu6616 obsolete
10 package outline figure 5: package outline - 14 pin 3 mm x 5 mm x 1 mm surface mount module figure 6: branding specifcation data sheet - rev 2.3 02/2012 awu6616 obsolete
11 ordering information order number temperature range package description component packaging awu6616q7 -30 c to +90 c rohs compliant 14 pin 3 mm x 5 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel AWU6616P9 -30 c to +90 c rohs compliant 14 pin 3 mm x 5 mm x 1 mm surface mount module partial tape and reel warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. i mpo r t an t n ot i ce ana d igi cs 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.3 02/2012 awu6616 obsolete

▲Up To Search▲

Price & Availability of AWU6616P9

	To Download AWU6616P9 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .