product bulletin dimensions ? millimeters (inches) eia size code metric size code l length w width b bandwidth s separation 0805 2012 2.0 (.079) 0.2 (.008) 1.25 (.049) 0.2 (.008) 0.5 (.02) 0.25 (.010) - 1206 3216 3.2 (.126) 0.2 (.008) 1.6 (.063) 0.2 (.008) 0.5 (.02) 0.25 (.010) - see capacitance value table for thickness dimension. outline drawing
surface mount ceramic chip capacitors ? low profile mlcc F9078c 08/07 capacitance values - x5r dielectric capacitance value ( f) kemet part number voltage capacitance tolerance thickness qty 7" reel 4.7 c0805l475(1 )9pac 6.3 10%, 20% 0.85 (.033) 0.1 (.004) 4,000 10.0 c0805l106(1 )9pac 6.3 10%, 20% 0.85 (.033) 0.1 (.004) 4,000 10.0 c0805l106(1 )8pac 10 10%, 20% 0.85 (.033) 0.1 (.004) 4,000 1.0 c1206l105(1) 3pac 25 10%, 20% 0.78 (.031) 0.1 (.004) 4,000 4.7 c1206l475(1) 4pac 16 10%, 20% 0.90 (.035) 0.1(.004) 4,000 (1) to complete kemet part number insert k for 10% or m for 20% capacitance tolerance. capacitance values - x7r dielectric capacitance value ( f) kemet part number voltage capacitance tolerance thickness qty 7" reel 1.0 c0805l105(1 )8rac 10 10%, 20% 0.78 (.031) 0.1 (.004) 4,000 (1) to complete kemet part number insert k for 10% or m for 20% capacitance tolerance.
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com c 0805 l 475 k 9 p a c style c - ceramic size code see dimension table specification l - low profile ceramic chip capacitance code, pf first two digits represent significant figures. third digit specifies number of zeros. 100 pf = 101. (use ?9? for 1.0 through 9.9 pf) (use ?8? for 0.1 through .99 pf) capacitance tolerance k = 10% m = 20% voltage 9 = 6.3v 8 = 10v 4 = 16v 3 = 25v temperature characteristic designated by capacitance change over temperature range r = x7r (15%) (-55c +125c) p = x5r (15%) (-55c +85c) end metallization c = standard (tin-plate nickel barrier) failure rate level a = not applicable capacitor ordering information electrical parameters - x5r dielectric as detailed in the kemet surface mount catalog f3102 for x5r, with following specific requirements based on room temperature (25c) parameters: ? operating range: -55c to +85c, with no-bias capacitance shift limited to 15% over that range. ? insulation resistance (ir) measured after 2 minutes at rated voltage @ 25c: limit is 500 megohm microfarads or 10000m , whichever is less. ? capacitance and dissipation factor (df) measured at the following conditions. df limit is 10%. 1 khz and 1 vrms. electrical parameters - x7r dielectric as detailed in the kemet surface mount catalog f3102 for x7r, with following specific requirements based on room temperature (25c) parameters: ? operating range: -55c to +125c, with no-bias capacitance shift limited to 15% over that range. ? insulation resistance (ir) measured after 2 minutes at rated voltage @ 25c: limit is 500 megohm microfarads or 10000m , whichever is less. ? capacitance and dissipation factor (df) measured at the following conditions. df limit is 5%. 1 khz and 1 vrms. soldering process these components are suitable for reflow only. all parts incorporate the standard kemet barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. marking these chips will be supplied unmarked. in general, the information in the kemet surface mount catalog f3102 applies to these capacitors. the information in this bulletin supplements that in the catalog.
|