- 656 - .118(3.0)x45 0 .043(1.1) .035(0.9) .087(2.2) .071(1.8) .303(7.7) .287(7.3) .030(0.75) .022(0.55) .709(18) .669(17) .068(1.73) .060(1.52) .176(4.37) .156(3.96) .147(3.7) .130(3.3) .602(15.3) .579(14.7) .134(3.4) .122(3.1) .996(25.3) .972(24.7) .366(9.3) .382(9.7) TSS4B01G thru tss4b03g single phase 4.0 amps. glass passivated super fast bridge rectifiers voltage range 50 to 200 volts current 4.0 amperes features ul recognized file # e-96005 glass passivated junction ideal for printed circuit board reliable low cost construction plastic material has underwriters laboratory flammability classification 94v-0 low forward voltage drop. high case dielectric strength of 2000v rms mechanical data case: molded plastic terminals: leads solderable per mil- std-750, method 2026 weight: 0.15 ounce, 4 grams mounting torque: 5 in. lbs. max. ts4b dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol TSS4B01G tss4b02g tss4b03g units maximum recurrent peak reverse voltage v rrm 50 100 200 v maximum rms voltage v rms 35 70 140 v maximum dc blocking voltage v dc 50 100 200 v maximum average forward rectified current @t c =100 o c i (av) 4.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 150 a maximum instantaneous forward voltage @ 4.0a v f 0.98 v maximum reverse recovery time(note 1) trr 35 ns maximum dc reverse current @ t a =25 at rated dc blocking voltage @ t a =125 i r 5.0 500 ua ua typical thermal resistance (note 2) r jc 5.5 / w operating temperature range t j -55 to +150 storage temperature range t stg -55 to + 150 note: 1. reverse recovery test conditions : i f =0.5a, i r =1.0a, i rr =0.25a. 2. thermal resistance from junction to case with device mounted on 2? x 3? x 0.25? al-plate heatsink.
- 657 - fig.3- typical reverse characteristics instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 1000 0.1 1.0 10 100 percent of rated peak reverse voltage. (%) tc=25 c 0 tc=100 c 0 fig.1- reverse recovery time characteristic and test circuit diagram 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm ratings and characteristic curves (TSS4B01G thru tss4b03g) fig.2- maximum forward current derating curve average for ward current . (a) 0 50 100 150 0 1 2 3 4 5 case temperature. ( c) o fig.4- maximum non-repetitive forward surge current per leg peak for ward surge current . (a) 1 2 5 10 20 100 50 75 150 125 100 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.6- typical forward characteristics per leg instantaneous for ward current . (a) .4 .6 .8 1.0 1.2 1.4 1.6 1.8 .01 0.1 .03 1.0 0.3 10 3.0 30 100 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o
|
