s s m m d d 8 8 0 0 2 2 - 1 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . features description ? > 90% efficiency ? universal rectified 85 ? 265v ac input range ? constant-current led driver ? applications from a few ma to more than 1a output ? led string from one to hundreds of diodes ? pwm low-frequency dimming via enable pin ? input voltage surge ratings up to 500v ? internal thermal overload protection ? tolerance of cs pin voltage is +/-5% the SMD802 is a pwm high-efficiency led driver control ic. it allows efficient operation of high brightness (hb) leds from voltage sources ranging from 85v ac up to 265v ac . the SMD802 controls an external mosfet at fixed switching frequency up to 300khz. the frequency can be programmed using a single external resistor. the led string is driven at constant current rather than constant voltage, thus providing constant light output and enhanced reliability. the output current can be programmed between a few milliamps and up to more than 1.0a. SMD802 uses a rugged high voltage junction isolated process that can withstand an input voltage surge of up to 500v. output current to an led string can be programmed to any value between zero and its maximum value by applying an external control voltage at the linear dimming control input of the SMD802. the SMD802 provides a low-frequency pwm dimming input that can accept an external control signal with a duty ratio of 0-100% and a frequency of up to a few kilohertz. applications ? ac/dc led driver applications ? rgb backlighting led driver ? back lighting of flat panel displays ? general purpose constant current source ? signage and decorative led lighting ? chargers package/order information order part number 8-pin plastic s.o.i.c. (top view) SMD802mst 8-pin plastic dip (top view) SMD802m universal high brightness led driver v in cs gnd gate pwm_d v dd ld. r osc vin cs gnd. gate pwm_d v dd ld r osc www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 2 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . pin functions pin no. pin name function 1 v in input voltage 2 cs senses led string current 3 gnd device ground 4 gate drives the gate of the external mosfet 5 pwm_d low frequency pwm dimming pin, also enable input. internal 100k ? pull-down to gnd 6 v dd internally regulated supply voltage. 7.5v nominal. can supply up to 1 ma for external circuitry. a sufficient storage capacitor is used to provide storage when the rectified ac input is near the zero crossings. 7 ld linear dimming by changing the current limit threshold at current sense comparator 8 r osc oscillator control. a resistor connect ed between this pin and ground sets the pwm frequency. www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 3 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . absolute maximum ratings (note 1) v in to gnd -0.5v to +520v cs -0.3v to (vdd + 0.3v) ld, pwm_d to gnd -0.3v to (vdd ? 0.3v) gate to gnd -0.3v to (vdd + 0.3v) v ddmax 13.5v continuous power dissipation (ta = 25 c) (note 1) 8 pin dip (derate 9mw/ c above +25 c 900mw 8 pin so (derate 6.3mw/ c above +25 c 630mw operating temperature range -40 c to +85 c junction termperature +125 c storage temperature range -65 c to +150 c note 1: exceeding these ratings could c ause permanent damage to the device. all voltages are with respect to ground. currents a re positive into, negative out of the specified terminal. block diagram 1.25v 1.25v 1.25v 250mv gate ld cs r osc v in v dd undervoltage lockout 6.7v / 6.2v pwm dimmin g reference voltage 1.25v oscillator thermal shutdown buffer s r q shutdown pwm_d www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 4 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . typical applications v dd r osc ld pwm_d gate gnd cs v in sets led current universal input 15v ? 500 v dc 85 ? 265 v ac rectified www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 5 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . electrical characteristics unless otherwise specified, t a = 25 o c. parameter test conditions symbol min typ max units input dc supply voltage range dc input voltage v lndc 15.0 500 v shut-down mode supply current pin pwm_d to gnd, v in = 15v l lnsd 0.4 1 ma internally regulated voltage v in = 15-500v, l dd(ext) =0, pin gate open v dd 7.0 7.5 8.0 v maximal pin vdd voltage when an external voltage applied to pin vdd v ddmax 13.5 v v dd current available for external circuitry 1 v in = 15-100v i dd(ext) 1.0 ma v dd under voltage lockout threshold vin rising uvlo 6.45 6.7 6.95 v v dd under voltage lockout hysteresis vin falling ? uvlo 520 mv pin pwm_d input low voltage v in = 15-500v v en(lo) 1.0 v pin pwm_d input high voltage v in = 15-500v v en(hi) 2.4 v pin pwm_d pull-down resistance v en = 5v r en 50 100 150 k ? current sense pull-in threshold voltage @ta = -40c to +85c v cs(hi) 238 250 262 mv gate high output voltage i out = 10ma v gate(hi) v dd -0.3 v dd v gate low output voltage i out = -10ma v gate(lo) 0 0.3 v r osc = 1.00m ? 20 24 30 oscillator frequency r osc = 226k ? f osc 80 96 120 khz maximum oscillator pwm duty cycle f pwmhf = 25khz, at gate, cs to gnd. d maxhf 100 % linear dimming pin voltage range @ta = <85c, vin = 20v v ld 0 v cs(hi) mv current sense blanking interval v cs = 0.55v ld , v ld = v dd t blank 200 280 360 ns delay from cs trip to gate lo vin = 20v, v ld = 0.15, v cs = 0 to 0.22v after t blank t delay 300 ns gate output rise time c gate = 500pf t rise 25 50 ns gate output fall time c gate = 500pf t fall 20 50 ns thermal shut down t sd 150 c www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 6 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . package description dimensions in inches (millimet ers) unless otherwise specified so 8 (0.356 - 0.508) (0.406 - 0.270) 0.016 - 0.050 d 0.189 - 0.197 (4.800 - 5.004) seating plan 0.014 - 0.020 0.150 - 0.157 (3.810 - 3.988) 0.008 - 0.010 (0.203 - 0.254) 8.0 max 0.053 - 0.059 (1.346 - 1.753) 0.004 - 0.010 0.228 - 0.244 (5.791 - 6.198) 0.050 (1.270) typ dip 8 0.300 - 0.320 (7.620 - 8.128) 0.045 +/- 0.015 (1.143 +/- 0.183) 0.250 +/- 0.005 (6.350 +/- 0.127) 0.370 - 0.400 (9.474 - 10.150) 0.06 (1.524) 0.145 - 0.200 (3.683 - 5.080) 0.125 - 0.140 (3.175 - 3.556) 0.108 +/- 0.003 (0.457 +/- 0.076) 0.100 +/- 0.010 (2.540 +/- 0.254) j 0.009 - 0.010 (0.299 - 0.381) 95 +/- 5 www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 7 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . marking diagram dip 8 so 8 yy = year, ww = working week, t = otp, f = wafer side, a = at side, lll = lot number 802m tfalll yyww yyww 802ms tfalll www.datasheet.net/ datasheet pdf - http://www..co.kr/
s s m m d d 8 8 0 0 2 2 - 8 - rev c smd doc #: dd0014 copy right ? 2010, shamrock micro device corp. ???? shamrock micro devices corp . important notice shamrock micro devices (smd) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, an d advises its customers to obtain the latest version of relevant information to verify, before placing orde rs, that the information being relied on is current. a few applications using integrated circuit products may involve potential risks of d eath, personal injury, or severe property or environmental damage. smd in tegrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-suppo rt applications, devices or systems or other critical applications. use of smd products in such applications is understood to be fully at the risk of the customer. in order to minimize risks associated with the custom er?s applications, the customer should provide adequate design and operating safeguards. www.datasheet.net/ datasheet pdf - http://www..co.kr/
|
