flexstrip flexstrip jumpers jumpers v v er er satile satile dependab dependab le le lo lo w cost w cost flexing stress is evenly distributed with flexstrip flat conductors vs. conventional wiring flexstrip jumpers ?flexstrip socket contacts provide a reliable system for flexstrip jumper quick disconnect applications ?flexstrip socket contacts withstand adverse envi- ronmental conditions such as corrosion 1308959-5m-tyco/c&ce-05/01 printed on recycled paper. tyco and amp are trademarks. c tyco electronics p.o. box 3608 harrisburg, pa usa 17105-3608
flexstrip jumpers ?one piece copper construction with round copper conductors rolled flat for high flex life, tin-plated for easy soldering ?available in 4 insulations for high volume commercial use as well as military/aero- space applicarions ?nomex, teflon, polyester and kapton round-to-flat design provides vibration- proof reliability and long life available in lengths from .5 inches to 34 inches in .100 increments ?provides lowest installed cost because no crimping or cutting is required ?space saver ?designed for long flex life ?lower installed cost flexstrip jumpers will flex your imagination in board-to-board interconnection applications with its industry leading improvements in contact reliability, low height pro- file, compatibility with pick and place equipment and ease of jumper assembly, flexstrip jumpers will prove to be the optimal solution for many applications including: ?laptop/palmtop ?computers ?handheld terminals ?bar code readers ?printers ?test equipment ?mobile radio ?telecommunications equipment ?automotive instrumentation (see inside for ordering information)
p arts d escription standard jumpers fs n-1 2 a-70 product code insulation material n - nomex t - teflon k - kapton p - polyester conductor pitch 1 - .050'' 2 - .100'' 3 - .125'' 4 - .150'' 5 - .200'' 6 - .075'' 7 - 2mm (.079'') 8 - 1.25mm (.049'') 9 - 1.0mm (.039'') insulation length .5'' min. to 34'' max. in .100'' increments pin arrangement (for both ends) a - straight pins b - right angle pins c - right angle staggered pins d - straight staggered pins note: see below for other pin arrangements number of conductors special jumpers fs n - 1 3.25 g h -20 v1 product code insulation material n - nomex t - teflon k - kapton p - polyester conductor pitch 1 - .050'' 2 - .100'' 3 - .125'' 4 - .150'' 5 - .200'' 6 - .075'' 7 - 2mm (.079'') 8 - 1.25mm (.049'') 9 - 1.0mm (.039'') insulation length .5'' min. to 34'' max. in .100'' increments (different termination on each end) left end right end number of conductors (max recommended width 4 inches) special pin length v1 - .112'' v2 - .134'' v3 - .161'' v4 - .256'' v5 - .122'' v6 - .150'' v7 - .177'' v8 - .079'' v9 - tbd v10 - tbd v11 - .095'' pin lenght tol. +0.012/-0.008
insulation material polyester nomex teflon kapton conductor pitch .100 .100 .100 .100 flammability rating v0 v0 v0 v0 equivalent conductor size 24 24 24 24 (american wire gauge) insulation resistance (gnd, sig, gnd) 12 inch. 1 x 10 12 ? 2 x 10 12 ? 2 x 10 12 ? 2 x 10 12 ? sample @ 500 vdc capacitance (picofarad/foot) 10.2 pf/ft 8.9 pf/ft 10.5 pf/ft 9.1 pf/ft (gnd, sig, gnd) characteristic impedance ? 118 ? 123 ? 101 ? 112 ? (gnd, sig, gnd) temperature rating 105 c 125 c 150 c 150 c current rating 3 amps 3 amps 3 amp 3 amps voltage rating 300 amps 300 amps 300 amps 300 amps min. breakdown 1500 volts 1500 volts 1500 volts 1500 volts voltage @1 min min. bend radus 1/8 1/8 1/8 1/8 no ozone depleting substances are used in the production processes for flexstrip jumpers. thickness for pcb with the number of pitch margin wire (pin end) pin dia. following diameter conductors ac gauge d e (?001) holes and recommended (?005) center tolerance (min. - max.) 1.00 (.039) .25 (.010) 28 .64 (.025) .320 (.0126) 2?0 1.25 (.049) .25 (.010) 28 .64 (.025) .320 (.0126) .71 (.028) 2?0 1.27 (.050) .25 (.010) 28 .64 (.025) .320 (.0126) .71 (.028) 2?0 1.90 (.075) .25 (.010) 26 .84 (.033) .404 (.0159) .79 (.031) 2?0 2.00 (.079) .25 (.010) 26 .84 (.033) .404 (.0159) .79 (.031) 2?0 2.54 (.100) .25 (.010) 24 .84 (.033) .511 (.0201) .94 (.037) 2?5 3.18 (.125) .51 (.020) 24 .84 (.033) .511 (.0201) .94 (.037) 2?5 3.81 (.150) .51 (.020) 24 .84 (.033) .511 (.0201) 94 (.037) 2?0 5.08 (.200) .51 (.020) 24 .84 (.033) .511 (.0201) 94 (.037) 2?2 tolerance on pitch: .25mm (?010), non-cumulative nomex, teflon and kapton are trademarks of e. i. dupont de nemours. mid-pin jumper thickness (.039), (.049), (.050), (.075), (.125), (.150), & (.200) .254 (.010) nomex .254 (.010) kapton .406 (.016) teflon .254 (.010) polyester 3.17 .76 (.125 .030 e pin dia. 025 ( .0010) b 1.57 ( .062) no nicks d (max.) 1 2 1 2 & jumper thickness between points c (min.) a tyco product specification and customer drawing: 1474339 technical documents technical support center phone: 1-800-522-6752 internet: www.amp.com
|
