View X28C512T-25_6773821.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev 1.0 6/27/00 characteristics subject to change without notice. 1 of 24 www.xicor.com 512k x28c512/x28c513 64k x 8 bit 5 volt, byte alterable eeprom features access time: 90ns simple byte and page write single 5v supply no external high voltages or v pp control circuits self-timed no erase before write no complex programming algorithms no overerase problem low power cmos active: 50ma standby: 500? software data protection protects data against system level inadvertent writes high speed page write capability highly reliable direct write cell endurance: 100,000 write cycles data retention: 100 years early end of write detection ? a t a polling toggle bit polling two plcc and lcc pinouts x28c512 x28c010 eprom pin compatible x28c513 compatible with lower density eeproms description the x28c512/513 is a 64k x 8 eeprom, fabricated with xicors proprietary, high performance, ?ating gate cmos technology. like all xicor programmable nonvolatile memories, the x28c512/513 is a 5v only device. the x28c512/513 features the jedec approved pin out for byte wide memories, compatible with industry standard eproms. the x28c512/513 supports a 128-byte page write operation, effectively providing a 39?/byte write cycle and enabling the entire memory to be written in less than 2.5 seconds. the x28c512/513 also features d a t a polling and toggle bit polling, system software support schemes used to indicate the early completion of a write cycle. in addition, the x28c512/513 supports the software data protection option. block diagram x buffers latches and decoder i/o buffers and latches y buffers latches and decoder control logic and timing 512kbit eeprom array i/o 0 ?/o 7 data inputs/outputs ce oe v cc v ss a 7 ? 15 we a 0 ? 6
x28c512/x28c513 characteristics subject to change without notice. 2 of 24 rev 1.0 6/27/00 www.xicor.com pin configurations 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 x28c512 oe a 10 ce i/o 7 i/o6 i/o 5 i/o 4 i/o 3 nc nc v ss nc nc i/o 2 i/o1 i/o 0 a 0 a 1 a 2 a 3 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 a 11 a 9 a 8 a 13 a14 nc nc nc we v cc nc nc nc nc a15 a 12 a 7 a 6 a 5 a 4 nc nc a 15 a 12 a 7 a 6 a 5 a 4 a 3 a 2 a 1 a 0 i/o 0 i/o 1 i/o 2 v ss 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 v cc we nc a 14 a 13 a 8 a 9 a 11 oe a 10 ce i/o 5 i/o 4 i/o 3 i/o 2 i/o 1 x28c512 plastic dip cerdip flat pack soic (r) bottom 14 a 0 16 i/o 1 18 v ss 11 a 3 9 a 5 7 a 7 15 i/o 0 17 i/o 2 19 i/o 3 5 a 15 2 nc 36 v cc 20 i/o 4 21 i/o 5 34 nc 23 i/o 7 25 a 10 27 a 11 29 a 8 22 i/o 6 32 nc 24 ce 26 oe 28 a 9 30 a 13 13 a 1 12 a 2 10 a 4 8 a 6 4 nc 3 nc 1 nc 35 we 33 nc 31 a 14 6 a 12 pga x28c512 a 7 a 6 a 5 a 4 a 3 a 2 a 1 a 0 i/o 0 a 13 a 8 a 9 a 11 oe a 10 ce i/o 7 a 14 i/o 1 a 12 a 15 nc nc v cc we nc 2 32 6 1 5 4 3 8 7 9 10 11 12 13 15 17 16 18 19 20 22 23 24 25 26 27 28 29 31 14 21 30 plcc/lcc i/o 2 v ss i/o 3 i/o 4 i/o 5 i/o 6 x28c513 a 6 a 5 a 4 a 3 a 2 a 1 a 0 nc i/o 0 a 9 a 11 nc oe a 10 ce i/o 6 a 8 i/o 1 a 7 a 12 v cc we 2 32 6 1 5 4 3 8 7 9 10 11 12 13 15 17 16 18 19 20 22 23 24 25 26 27 28 29 31 14 21 30 i/o 2 v ss nc i/o 3 i/o 4 i/o 5 a 14 a 15 a 13 i/o 7 tsop view (top view) (top view) pin descriptions addresses (a 0 ? 15 ) the address inputs select an 8-bit memory location during a read or write operation. chip enable (ce ) the chip enable input must be low to enable all read/ write operations. when ce is high, power consump- tion is reduced. output enable (oe ) the output enable input controls the data output buff- ers and is used to initiate read operations. data in/data out (i/o 0 ?/o 7 ) data is written to or read from the x28c512/513 through the i/o pins. write enable (we ) the write enable input controls the writing of data to the x28c512/513. pin names symbol description a 0 ? 15 address inputs i/o 0 ?/o 7 data input/output we write enable ce chip enable oe output enable v cc +5v v ss ground nc no connect
x28c512/x28c513 characteristics subject to change without notice. 3 of 24 rev 1.0 6/27/00 www.xicor.com device operation read read operations are initiated by both oe and ce low. the read operation is terminated by either ce or oe returning high. this two line control architecture elimi- nates bus contention in a system environment. the data bus will be in a high impedance state when either oe or ce is high. write write operations are initiated when both ce and we are low and oe is high. the x28c512/513 supports both a ce and we controlled write cycle. that is, the address is latched by the falling edge of either ce or we , whichever occurs last. similarly, the data is latched internally by the rising edge of either ce or we , whichever occurs ?st. a byte write operation, once initiated, will automatically continue to comple- tion, typically within 5ms. page write operation the page write feature of the x28c512/513 allows the entire memory to be written in 2.5 seconds. page write allows two to one hundred twenty-eight bytes of data to be consecutively written to the x28c512/513, prior to the commencement of the internal programming cycle. the host can fetch data from another device within the system during a page write operation (change the source address), but the page address (a 7 through a 15 ) for each subsequent valid write cycle to the part during this operation must be the same as the initial page address. the page write mode can be initiated during any write operation. following the initial byte write cycle, the host can write an additional one to one hundred twenty- seven bytes in the same manner as the ?st byte was written. each successive byte load cycle, started by the we high to low transition, must begin within 100? of the falling edge of the preceding we . if a sub- sequent we high to low transition is not detected within 100?, the internal automatic programming cycle will commence. there is no page write window limitation. effectively, the page write window is in?itely wide, so long as the host continues to access the device within the byte load cycle time of 100?. write operation status bits the x28c512/513 provides the user two write opera- tion status bits. these can be used to optimize a sys- tem write cycle time. the status bits are mapped onto the i/o bus as shown in figure 1. figure 1. status bit assignment data polling (i/o 7 ) the x28c512/513 features d a t a polling as a method to indicate to the host system that the byte write or page write cycle has completed. d a t a polling allows a simple bit test operation to determine the status of the x28c512/513, eliminating additional interrupt inputs or external hardware. during the internal programming cycle, any attempt to read the last byte written will pro- duce the complement of that data on i/o 7 (i.e. write data = 0xxx xxxx, read data = 1xxx xxxx). once the programming cycle is complete, i/o 7 will re?ct true data. toggle bit (i/o 6 ) the x28c512/513 also provides another method for determining when the internal write cycle is complete. during the internal programming cycle, i/o 6 will toggle from high to low and low to high on subsequent attempts to read the device. when the internal cycle is complete, the toggling will cease, and the device will be accessible for additional read or write operations. 5 tb dp 43210 i/o reserved toggle bit data polling
x28c512/x28c513 characteristics subject to change without notice. 4 of 24 rev 1.0 6/27/00 www.xicor.com data polling i/o 7 figure 2a. data polling bus sequence ce oe we i/o 7 x28c512/513 ready last write high z v ol v ih a 0 ? 15 a n a n a n a n a n a n v oh a n figure 2b. data polling software flow d a t a polling can effectively halve the time for writing to the x28c512/513. the timing diagram in figure 2a illustrates the sequence of events on the bus. the soft- ware ?w diagram in figure 2b illustrates one method of implementing the routine. write data save last data and address read last address io 7 compare? ready no yes writes complete? no yes
x28c512/x28c513 characteristics subject to change without notice. 5 of 24 rev 1.0 6/27/00 www.xicor.com the toggle bit i/o 6 figure 3a. toggle bit bus sequence ce oe we x28c512/513 last write i/o 6 high z * * v oh v ol ready * beginning and ending state of i/o 6 will vary. figure 3b. toggle bit software flow the toggle bit can eliminate the chore of saving and fetching the last address and data in order to imple- ment d a t a polling. this can be especially helpful in an array comprised of multiple x28c512/513 memories that is frequently updated. toggle bit polling can also provide a method for status checking in multiprocessor applications. the timing diagram in figure 3a illustrates the sequence of events on the bus. the software ?w diagram in figure 3b illustrates a method for polling the toggle bit. hardware data protection the x28c512/513 provides three hardware features that protect nonvolatile data from inadvertent writes. noise protection? we pulse typically less than 10ns will not initiate a write cycle. default v cc sense?ll write functions are inhibited when v cc is 3.6v. write inhibit?olding either oe low, we high, or ce high will prevent an inadvertent write cycle dur- ing power-up and power-down, maintaining data integrity. write cycle timing speci?ations must be observed concurrently. software data protection the x28c512/513 offers a software controlled data protection feature. the x28c512/513 is shipped from xicor with the software data protection not enabled; that is, the device will be in the standard operating mode. in this mode data should be protected during power-up/-down operations through the use of external circuits. the host would then have open read and write access of the device once v cc was stable. compare x28c512 no yes ok? compare accum with addr n load accum from addr n last write ready
x28c512/x28c513 characteristics subject to change without notice. 6 of 24 rev 1.0 6/27/00 www.xicor.com the x28c512/513 can be automatically protected dur- ing power-up and power-down without the need for external circuits by employing the software data pro- tection feature. the internal software data protection circuit is enabled after the ?st write operation utilizing the software algorithm. this circuit is nonvolatile and will remain set for the life of the device unless the reset command is issued. once the software protection is enabled, the x28c512/ 513 is also protected from inadvertent and accidental writes in the powered-up state. that is, the software algorithm must be issued prior to writing additional data to the device. note: the data in the three-byte enable sequence is not written to the memory array. software algorithm selecting the software data protection mode requires the host system to precede data write operations by a series of three write operations to three speci? addresses. refer to figure 4a and 4b for the sequence. the three byte sequence opens the page write window, enabling the host to write from one to one hundred twenty-eight bytes of data. once the page load cycle has been completed, the device will auto- matically be returned to the data protected state. software data protection figure 4a. timing sequence?oftware data protect enable sequence followed by byte or page write ce we (v cc ) write protected v cc 0v data addr aaa 5555 55 2aaa a0 5555 t blc max writes ok byte or page t wc note: all other timings and control pins are per page write timing requirements
x28c512/x28c513 characteristics subject to change without notice. 7 of 24 rev 1.0 6/27/00 www.xicor.com figure 4b. write sequence for software data protection regardless of whether the device has previously been protected or not, once the software data protected algorithm is used and data has been written, the x28c512/513 will automatically disable further writes, unless another command is issued to cancel it. if no further commands are issued the x28c512/513 will be write protected during power-down and after any sub- sequent power-up. the state of a 15 while executing the algorithm is don? care. note: once initiated, the sequence of write operations should not be interrupted. write last write data xx to any write data 80 to address 5555 write data 55 to address 2aaa write data aa to address 5555 after t wc re-enters data protected state byte to last address address optional byte/page load operation
x28c512/x28c513 characteristics subject to change without notice. 8 of 24 rev 1.0 6/27/00 www.xicor.com resetting software data protection figure 5a. reset software data protection timing sequence ce we standard operating mode v cc data addr aaa 5555 55 2aaa 80 5555 t wc aa 5555 55 2aaa 20 5555 note: all other timings and control pins are per page write timing requirements figure 5b. software sequence to deactivate software data protection in the event the user wants to deactivate the software data protection feature for testing or reprogramming in an eeprom programmer, the following six step algo- rithm will reset the internal protection circuit. after t wc , the x28c512/513 will be in standard operating mode. note: once initiated, the sequence of write operations should not be interrupted. system considerations because the x28c512/513 is frequently used in large memory arrays it is provided with a two line control architecture for both read and write operations. proper usage can provide the lowest possible power dissipa- tion and eliminate the possibility of contention where multiple i/o pins share the same bus. to gain the most bene? it is recommended that ce be decoded from the address bus and be used as the pri- mary device selection input. both oe and we would then be common among all devices in the array. for a read operation this assures that all deselected devices are in their standby mode and that only the selected device(s) is/are outputting data on the bus. because the x28c512/513 has two power modes, (standby and active), proper decoupling of the memory array is of prime concern. enabling ce will cause tran- sient current spikes. the magnitude of these spikes is dependent on the output capacitive loading of the i/os. therefore, the larger the array sharing a common bus, the larger the transient spikes. the voltage peaks associated with the current transients can be sup- pressed by the proper selection and placement of decoupling capacitors. as a minimum, it is recom- mended that a 0.1? high frequency ceramic capacitor be used between v cc and v ss at each device. depending on the size of the array, the value of the capacitor may have to be larger. write data 55 to address 2aaa write data 55 to address 2aaa write data a0 to address 5555 write data aa to address 5555 write data 20 to address 5555 write data aa to address 5555
x28c512/x28c513 characteristics subject to change without notice. 9 of 24 rev 1.0 6/27/00 www.xicor.com in addition, it is recommended that a 4.7? electrolytic bulk capacitor be placed between v cc and v ss for each 8 devices employed in the array. this bulk capaci- tor is employed to overcome the voltage droop caused by the inductive effects of the pc board traces. active supply current vs. ambient temperature standby supply current vs. ambient temperature i cc (rd) by temperature over frequency ?5 ?0 +125 10 11 12 13 14 ambient temperature (?) 8 +35 +80 v cc = 5v 9 i cc (ma) ?5 ?0 +125 0.14 0.16 0.18 0.2 0.24 ambient temperature (?) 0.1 +35 +80 0.22 v cc = 5v 0.12 i sb (ma) 0 315 30 40 50 60 5.0 v cc frequency (mhz) 10 69 ?5? +25? +125? 12 20 70 i cc (ma)
x28c512/x28c513 characteristics subject to change without notice. 10 of 24 rev 1.0 6/27/00 www.xicor.com absolute maximum ratings temperature under bias x28c512/513...................................?0? to +85? x28c512i/513i...............................?5? to +135? x28c512m/513m...........................?5? to +135? storage temperature .........................?5? to +150? voltage on any pin with respect to v ss ......................................... ?v to +7v d.c. output current ............................................... 5ma lead temperature (soldering, 10 seconds) ..................................300? comment stresses above those listed under ?bsolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device (at these or any other conditions above those indi- cated in the operational sections of this speci?ation) is not implied. exposure to absolute maximum rating condi- tions for extended periods may affect device reliability. recommend operating conditions temperature min. max. commercial 0? +70? industrial ?0? +85? military ?5? +125? supply voltage limits x28c512/513 5v ?0% d.c. operating characteristics (over recommended operating conditions, unless otherwise specified.) note: (1) v il min. and v ih max. are for reference only and are not tested. power-up timing symbol parameter limits unit test conditions min. max. i cc v cc current (active) (ttl inputs) 50 ma ce = oe = v il , we = v ih , all i/o? = open, address inputs = .4v/2.4v levels @ f = 5mhz i sb1 v cc current (standby) (ttl inputs) 3mace = v ih , oe = vil, all i/o? = open, other inputs = v ih i sb2 v cc current (standby) (cmos inputs) 500 ? ce = v cc ?0.3v, oe = vil, all i/o? = open, other inputs = v ih i li input leakage current 10 ? v in = v ss to v cc i lo output leakage current 10 ? v out = v ss to v cc , ce = v ih v ll (1) input low voltage ? 0.8 v v ih (1) input high voltage 2 v cc + 1 v v ol output low voltage 0.4 v i ol = 2.1ma v oh output high voltage 2.4 v i oh = ?00? symbol parameter max. unit t pur (2) power-up to read operation 100 ? t puw (2) power-up to write operation 5 ms
x28c512/x28c513 characteristics subject to change without notice. 11 of 24 rev 1.0 6/27/00 www.xicor.com capacitance t a = +25?, f = 1mhz, v cc = 5v endurance and data retention symbol parameter max. unit test conditions c i/o (2) input/output capacitance 10 pf v i/o = 0v c in (2) input capacitance 10 pf v in = 0v parameter min. max. unit endurance 10,000 cycles per byte endurance 100,000 cycles per page data retention 100 years a.c. conditions of test mode selection equivalent a.c. load circuit note: (2) this parameter is periodically sampled and not 100% tested. symbol table input pulse levels 0v to 3v input rise and fall times 10ns input and output timing levels 1.5v ce oe we mode i/o power l l h read d out active l h l write d in active hxx standby and write inhibit high z standby x l x write inhibit x x h write inhibit 5v 1.92k ? 100pf output 1.37k ? waveform inputs outputs must be steady will be steady may change from low to high will change from low to high may change from high to low will change from high to low don? care: changes allowed changing: state not known n/a center line is high impedance
x28c512/x28c513 characteristics subject to change without notice. 12 of 24 rev 1.0 6/27/00 www.xicor.com a.c. characteristics (over the recommended operating conditions, unless otherwise specified.) read cycle limits read cycle note: (3) t lz min., t hz , t olz min., and t ohz are periodically sampled and not 100% tested. t hz max. and t ohz max. are measured, with c l = 5pf from the point when ce or oe return high (whichever occurs ?st) to the time when the outputs are no longer driven. symbol parameter x28c512-90 x28c512-12 x28c512-15 x28c512-20 x28c512-25 unit x28c513-90 x28c513-12 x28c513-15 x28c513-20 x28c513-25 min. max. min. max. min. max. min. max. min. max. t rc read cycle time 90 120 150 200 250 ns t ce chip enable access time 90 120 150 200 250 ns t aa address access time 90 120 150 200 250 ns t oe output enable access time 40 50 50 50 50 ns t lz (3) ce low to active output 0 0 0 0 0 ns t olz (3) oe low to active output 0 0 0 0 0 ns t hz (3) ce high to high z output 40 50 50 50 50 ns t ohz (3) oe high to high z output 40 50 50 50 50 ns t oh output hold from address change 00000 ns t ce t rc address ce oe we data valid t oe t lz t olz t oh t aa t hz t ohz data i/o v ih high z data valid
x28c512/x28c513 characteristics subject to change without notice. 13 of 24 rev 1.0 6/27/00 www.xicor.com write cycle limits we controlled write cycle note: (4) t wc is the minimum cycle time to be allowed from the system perspective unless polling techniques are used. it is the maximum time the device requires to complete the internal write operation. symbol parameter min. max. unit t wc (4) write cycle time 10 ms t as address setup time 0 ns t ah address hold time 50 ns t cs write setup time 0 ns t ch write hold time 0 ns t cw ce pulse width 100 ns t oes oe high setup time 10 ns t oeh oe high hold time 10 ns t wp we pulse width 100 ns t wph we high recovery 100 ns t dv data valid 1 s t ds data setup 50 ns t dh data hold 0 ns t dw delay to next write 10 ? t blc byte load cycle 0.2 100 ? address t as t wc t ah t oes t dv t ds t dh t oeh ce we oe data in data out high z data valid t cs t ch t wp
x28c512/x28c513 characteristics subject to change without notice. 14 of 24 rev 1.0 6/27/00 www.xicor.com ce controlled write cycle page write cycle notes: (5) between successive byte writes within a page write operation, oe can be strobed low: e.g. this can be done with ce and we high to fetch data from another memory device within the system for the next write; or with we high and ce low effectively per- forming a polling operation. (6) the timings shown above are unique to page write operations. individual byte load operations within the page write must conf orm to either the ce or we controlled write cycle timing. address t as t oeh t wc t ah t oes t cs t dv t ds t dh t ch ce we oe data in data out high z data valid t cw t wph we oe (5) last byte byte 0 byte 1 byte 2 byte n byte n+1 byte n+2 t wp t wph t blc t wc ce address* (6) i/o *for each successive write within the page write operation, a 7 ? 15 should be the same or writes to an unknown address could occur.
x28c512/x28c513 characteristics subject to change without notice. 15 of 24 rev 1.0 6/27/00 www.xicor.com data polling timing diagram (7) toggle bit timing diagram note: (7) polling operations are by de?ition read cycles and are therefore subject to read cycle timings. address a n d in = x t wc t oeh t oes ce we oe i/o 7 t dw a n a n d out = x d out = x ce oe we i/o 6 t oes t dw t wc t oeh high z * * *starting and ending state will vary, depending upon actual t wc .
x28c512/x28c513 characteristics subject to change without notice. 16 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 0.620 (15.75) 0.590 (14.99) typ. 0.614 (15.60) 0.110 (2.79) 0.090 (2.29) typ. 0.100 (2.54) 1.690 (42.95) max. 0.023 (0.58) 0.014 (0.36) typ. 0.018 (0.46) 0.232 (5.90) max. 0.060 (1.52) 0.015 (0.38) pin 1 0.200 (5.08) 0.125 (3.18) 0.065 (1.65) 0.033 (0.84) typ. 0.055 (1.40) 0.610 (15.49) 0.500 (12.70) 0.100 (2.54) max. 0 15 32-lead hermetic dual in-line package type d note: all dimensions in inches (in parentheses in millimeters) 0.005 (0.13) min. 0.150 (3.81) min. 0.015 (0.38) 0.008 (0.20) seating plane
x28c512/x28c513 characteristics subject to change without notice. 17 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 0.150 (3.81) bsc 0.458 (11.63) 0.458 (11.63) 0.442 (11.22) pin 1 0.020 (0.51) x 45? ref. 0.095 (2.41) 0.075 (1.91) 0.022 (0.56) 0.006 (0.15) 0.055 (1.39) 0.045 (1.14) typ. (4) plcs. 0.040 (1.02) x 45? ref. typ. (3) plcs. 0.050 (1.27) bsc 0.028 (0.71) 0.022 (0.56) (32) plcs. 0.200 (5.08) bsc 0.558 (14.17) 0.088 (2.24) 0.050 (1.27) 0.120 (3.05) 0.060 (1.52) pin 1 index corner 32-pad ceramic leadless chip carrier package type e note: 1. all dimensions in inches (in parentheses in millimeters) 2. tolerance: ?% nlt ?.005 (0.127) 0.300 (7.62) bsc 0.015 (0.38) min. 0.400 (10.16) bsc 0.560 (14.22) 0.540 (13.71) dia. 0.015 (0.38) 0.003 (0.08)
x28c512/x28c513 characteristics subject to change without notice. 18 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 32-lead ceramic flat pack type f note: all dimensions in inches (in parentheses in millimeters) 0.019 (0.48) 0.015 (0.38) 0.045 (1.14) max. pin 1 index 132 0.120 (3.05) 0.090 (2.29) 0.045 (1.14) 0.026 (0.66) 0.007 (0.18) 0.004 (0.10) 0.370 (9.40) 0.270 (6.86) 0.830 (21.08) max. 0.050 (1.27) bsc 0.488 0.430 (10.93) 0.347 (8.82) 0.330 (8.38) 0.005 (0.13) min. 0.030 (0.76) min. 1.228 (31.19) 1.000 (25.40)
x28c512/x28c513 characteristics subject to change without notice. 19 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 0.021 (0.53) 0.013 (0.33) 0.420 (10.67) 0.050 (1.27) typ. typ. 0.017 (0.43) 0.045 (1.14) x 45 0.300 (7.62) ref. 0.453 (11.51) 0.447 (11.35) typ. 0.450 (11.43) 0.495 (12.57) 0.485 (12.32) typ. 0.490 (12.45) pin 1 0.400 (10.16) ref. 0.553 (14.05) 0.547 (13.89) typ. 0.550 (13.97) 0.595 (15.11) 0.585 (14.86) typ. 0.590 (14.99) 3 typ. 0.048 (1.22) 0.042 (1.07) 0.140 (3.56) 0.100 (2.45) typ. 0.136 (3.45) 0.095 (2.41) 0.060 (1.52) 0.015 (0.38) seating plane 0.004 lead co ?planarity 32-lead plastic leaded chip carrier package type j notes: 1. all dimensions in inches (in parentheses in millimeters) 2. dimensions with no tolerance for reference only 0.510" typical 0.050" typical 0.050" typical 0.300" ref. foo tprint 0.400" 0.410" 0.030" typical 32 places
x28c512/x28c513 characteristics subject to change without notice. 20 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 1. all dimensions in inches (in parentheses in millimeters) 2. package dimensions exclude molding flash 0.022 (0.56) 0.014 (0.36) 0.160 (4.06) 0.125 (3.17) 0.625 (15.88) 0.590 (14.99) 0.110 (2.79) 0.090 (2.29) 1.665 (42.29) 1.644 (41.76) 1.500 (38.10) ref. pin 1 index 0.160 (4.06) 0.140 (3.56) 0.030 (0.76) 0.015 (0.38) pin 1 seating plane 0.070 (17.78) 0.030 (7.62) 0.557 (14.15) 0.510 (12.95) 0.085 (2.16) 0.040 (1.02) 0 15 32-lead plastic dual in-line package type p typ. 0.010 (0.25) notes:
x28c512/x28c513 characteristics subject to change without notice. 21 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 32-lead ceramic small outline gull wing package type r 1. all dimensions in inches 2. formed lead shall be planar with respect to one another within 0.004 inches 0.340 ?.007 see detail ?? for lead information 0.440 max. 0.560 nom. 0.0192 0.0138 0.050 0.750 ?.005 0.840 max. 0.060 nom. 0.020 min. 0.015 r typ. 0.035 min. 0.015 r typ. 0.035 typ. detail ? 0.560" typical 0.050" typical 0.050" typical footprint 0.030" typical 32 places 0.165 typ. notes:
x28c512/x28c513 characteristics subject to change without notice. 22 of 24 rev 1.0 6/27/00 www.xicor.com packaging information 36-lead ceramic pin grid array package type k 15 17 19 21 22 14 16 18 20 23 10 9 27 28 8 7 29 30 5 2 36 34 32 4 3 1 35 33 typ. 0.100 (2.54) all leads pin 1 index note: leads 5, 14, 23, & 32 12 11 25 26 13 6 31 24 typ. 0.180 (.010) (4.57 ?.25) 4 corners 0.770 (19.56) 0.750 (19.05) sq a a 0.185 (4.70) 0.175 (4.45) 0.020 (0.51) 0.016 (0.41) 0.072 (1.83) 0.062 (1.57) 0.120 (3.05) 0.100 (2.54) note: all dimensions in inches (in parentheses in millimeters) typ. 0.180 (.010) (4.57 ?.25) 4 corners 0.050 (1.27) 0.008 (0.20) a a
x28c512/x28c513 characteristics subject to change without notice. 23 of 24 rev 1.0 6/27/00 www.xicor.com packaging information note: all dimensions are shown in millimeters (inches in parentheses). 0.50 ?0.04 (0.0197 ?0.0016) 0.30 ?0.05 (0.012 ?0.002) 14.80 ?0.05 (0.583 ?0.002) 1.30 ?0.05 (0.051 ?0.002) 0.17 (0.007) 0.03 (0.001) typical 40 places 15 eq. spc.@ 0.50 ?0.04 0.0197 0.016 = 9.50 ?0.06 (0.374 ?0.0024) overall tol. non-cumulative solder footprint 0.396 (10.058) 0.392 (9.957) 0.493 (12.522) 0.483 (12.268) pin #1 ident o 0.040 (1.016) o 0.030 (0.762) 1 (0.038) 0.045 (1.143) 0.035 (0.889) 0.0025 (0.065) 0.557 (14.148) 0.547 (13.894) seating plane a 0.007 (0.178) 0.040 (1.016) 15?typ. 0.0197 (0.500) 0.048 (1.219) 0.010 (0.254) 0.006 (0.152) 0.017 (0.432) 0.032 (0.813) typ. 0.017 (0.432) 0.020 (0.508) typ. 0.006 (0.152) detail a 40-lead thin small outline package (tsop) type t 0.965 x 0.005 (0.127) dp. 0.003 (0.076) dp. plane seating typ. 4?typ. pads
x28c512/x28c513 characteristics subject to change without notice. 24 of 24 limited warranty devices sold by xicor, inc. are covered by the warranty and patent indemni?ation provisions appearing in its terms of sale onl y. xicor, inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the descr ibed devices from patent infringement. xicor, inc. makes no warranty of merchantability or ?ness for any purpose. xicor, inc. reserves the right to discontinue produ ction and change speci?ations and prices at any time and without notice. xicor, inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a xicor, inc. product. no o ther circuits, patents, or licenses are implied. trademark disclaimer: xicor and the xicor logo are registered trademarks of xicor, inc. autostore, direct write, block lock, serialflash, mps, and xd cp are also trademarks of xicor, inc. all others belong to their respective owners. u.s. patents xicor products are covered by one or more of the following u.s. patents: 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084, 667; 5,153,880; 5,153,691; 5,161,137; 5,219,774; 5,270,927; 5,324,676; 5,434,396; 5,544,103; 5,587,573; 5,835,409; 5,977,585. foreign patents and addition al patents pending. life related policy in situations where semiconductor component failure may endanger life, system designers using this product should design the sy stem with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. xicors products are not authorized for use in critical components in life support devices or systems. 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) sup port or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to res ult in a signi?ant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ?icor, inc. 2000 patents pending rev 1.0 6/27/00 www.xicor.com ordering information access time ?0 = 90ns ?2 = 120ns ?5 = 150ns ?0 = 200ns ?5 = 250ns temperature range blank = commercial = 0? to +70? i = industrial = ?0? to +85? m = military = ?5? to +125? mb = mil-std-883 package d = 32-lead cerdip e = 32-pad lcc f = 32-lead flat pack j = 32-lead plcc k = 36-lead pin grid array p = 32-lead plastic dip r = 32-lead ceramic soic t = 40-lead tsop x28c512 x x -x device access time ?0 = 90ns ?2 = 120ns ?5 = 150ns ?0 = 200ns ?5 = 250ns temperature range blank = commercial = 0? to +70? i = industrial = ?0? to +85? m = military = ?5? to +125? mb = mil-std-883 package e = 32-pad lcc j = 32-lead plcc x28c513 x x -x device

▲Up To Search▲

Price & Availability of X28C512T-25

	To Download X28C512T-25 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .