ccd multichannel detector heads designed for back-thinned ccd area image sensor www.hamamatsu.com c7043 c7044 1 the c7043 and c7044 are high sensitivity multichannel detector heads for use with back-thinned fft-ccd area image sensors (s703 3/ s7034 series) that offer large full well capacity. the c7043 is designed for the non-cooled back-thinned type (s7033 series), w hile the c7044 for the one-stage te-cooled type (s7034 series) for detection at even lower light levels. both the c7043 and c7044 in - corporate a low-noise driver/ampli er circuit that provides reliable operation from simple external signals. the c7044 also includes a highly stable temperature controller that cools the sensor to a preset temperature level (ts=-10 c) as soon as the power is tu rned on. if the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. despite its compact size, the housing con guration is designed for good heat dissipation, and threaded mount- ing holes on the front panel allow connections to other devices such as monochrometers. controller for multichannel detector head c7557-01 is also available. the software supplied with the c7557-01 allows easy contr ol of the multichannel detector head and data acquisition. features applications designed for back-thinned ccd area image sensor * 1 c7043: for non-cooled type c7044: for te-cooled type fluorescence spectroscopy raman spectroscopy other low-light-level detection highly stable temperature controller (c7044) cooling temperature: -10 c 0.05 c line binning operation * 2 /area scanning operation simple signal input operation compact con guration driver/ampli er circuit for low noise ccd operation selection guide the table below shows ccd area image sensors applicable for the c7043 and c7044. since the c7043 and c7044 do not include a ccd area image sensor, so select the desired sensor and order it separately. type no. ccd area image sensor type no. number of pixels number of active pixels active area [mm (h) mm (v)] c7043 s7033-0907 532 128 512 122 12.288 2.928 s7033-1007 1044 128 1024 122 24.576 2.928 c7044 S7034-0907S 532 128 512 122 12.288 2.928 s7034-1007s 1044 128 1024 122 24.576 2.928 * 1: in normal ccd image sensors that receive light from the front surf ace, the active area is covered with electrodes for charge transfer. these electrodes cut off uv radiation incident on the image sensor and also reduce the quantum ef ciency. in contrast, back-thinned ccd image sensors have a unique structure in which the back of the active area is nely ground to allow light to enter from the back surface. this structure ensures high uv sensitivity and quantum ef ciency because incident light need not pass through the electrodes. * 2: the ccd area image sensor can be operated like a linear image sensor having a large active area by transferring all the pixe l signals in the vertical direction to the horizontal register (this is referred to as line binning).
ccd multichannel detector heads c7043, c7044 2 absolute maximum ratings electrical characteristics (ta=25 c, v d1 =+5 v, v a1+ =+15 v, v a1- =-15 v, v a2 =+24 v, v d2 =+5 v, vp=+5 v, v f =+12 v, unless otherwise noted) parameter symbol min. typ. max. unit supply voltage (for digital circuitry) v d1 , v d2 -0.5 - +7 v supply voltage (for analog circuitry) v a1+ - - +18 v a1- - - -18 v a2 - - +30 supply voltage vp - - +7 v f - - +14 digital input voltage - - - v d1 operating temperature c7043 topr 0 - +50 c c7044 +10 - +35 * 3 storage temperature c7043 tstg -20 - +70 c7044 0 - +50 * 3: the maximum value may be lower, depending on the drive frequency and the number of sensor pixels. parameter symbol min. typ. max. unit digital input high level v ih +2.0 - v d (1, 2) v low level v il -0.5 - +0.8 v clk frequency f clk - - 1 mhz data video readout frequency fv - - f clk /4 hz start pulse width tst 1/fclk - - s digital output high level (i o =-6 ma) v ih +2.0 - - v low level (i o =+6 ma) v il - - +0.8 v power supply operating conditions voltage digital circuitry v d1 +4.75 +5.0 +5.25 v analog circuitry v a1+ +14.5 +15.0 +15.5 v v a1- -14.5 -15.0 -15.5 v v a2 +23.5 +24.0 +24.5 v other * 4 v d2 +4.75 +5.0 +5.25 v vp +4.75 +5.0 +5.25 v v f +11.75 +12.0 +12.25 v current v d1 (+5 vdc) - - - +200 ma v a1+ (+15 vdc) - - - +100 ma v a1- (-15 vdc) - - - -100 ma v a2 (+24 vdc) - - - +30 ma v d2 (+6 vdc) * 4 - - - +30 ma vp (+6 vdc) * 4 - - - +2.5 a v f (+12 vdc) * 4 - - +100 - ma * 4: c7044 electrical and optical characteristics (ta=25 c, ts=-10 c, v d1 =+5 v, v a1+ =+15 v, v a1- =-15 v, v a2 =+24 v, v d2 =+5 v, vp=+5 v, v f =+12 v) parameter symbol min. typ. max. unit spectral response range sr - 200 to 1100 -nm full well capacity vertical fw 180 360 - ke - horizontal - 3400 - conversion gain * 5 sv-3- v/e - dark current * 6 c7043 ds - 100 1000 e - /pixel/s c7044 - 3 30 readout noise nr - 60 - e - rms dynamic range dr - 56667 - - photo response non-uniformity * 7 prnu - 3 10 % * 5: including the circuit gain * 6: horizontal register value * 7: measured at 50 % of the full well capacity
ccd multichannel detector heads c7043, c7044 spectral response dark current vs. temperature 100 90 80 70 60 50 40 30 20 10 0 quantum efficiency (%) 200 400 600 800 1000 1200 wavelength (nm) (typ. ta=25 c) back- thinned ccd front- illuminated ccd -50 -40 -30 -20 0 -10 10 20 30 temperature (c) 0.01 1 0.1 10 100 1000 dark current (e - /pixel/s) (typ.) kmpdb0038ea kmpdb0256ea speci cations for temperature controller (c7044) (ta=25 c, v d1 =+5 v, v a1+ =+15 v, v a1- =-15 v, v a2 =+24 v, v d2 =+5 v, vp=+5 v, v f =+12 v) parameter * 8 symbol min. typ. max. unit cooling temperature ts -11 -10 -9 c temperature control range ts -0.05 - +0.05 c power dissipation of te-cooler element pp - - 7 w cool down time to reset temperature to - - 5 min. setting temperature for overheat protection * 9 to - +45 - c * 8: other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor . * 9: temperature of rear-side of housing (part to x fan) 3 block diagram (s7033/s7034 series) 23 22 21 20 14 15 24 1 2 12 11 89 3 4 5 2-bevel signal out 2 n blank (4 pixels) blank (4 pixels) v=58, 122, 250 h=512, 1024 4-bevel thinning thinning 1 23 45 2 3 4 5 v h 6-bevel 6-bevel 13 10 signal out 2 n kmpdc0016eb
ccd multichannel detector heads c7043, c7044 block diagram (c7044) kaccc0114eb 4 led th.h p+ p- th+ temperature controller * timing generator d.gnd a.gnd clk start trigger eos te-cooler vdd ccd area image sensor s7034 series buffer low-pass filter data video pre-amp driver regulator vee clamp od rd og ig1h, ig2h ig1v, ig2v p1v, p2v, tg p1h, p2h sg rg ss, isv, ish os th- mode select vp (+5 v) p.gnd v d2 (+5 v) d.gnd v f (+12 v) f.gnd temp monitor inverter cooling control v d1 (+5 v) v a1 + (+15 v) v a1 - (-15 v) v a2 (+24 v) * the c7043 does not include the temperature controller and te-cooler. timing chart (line binning operation) kaccc0115ec m=128 n=532, 1044 v-ch1--v-ch2, v-ch (m-3)--v-ch (m): isolation pixels h-ch1--h-ch4, h-ch (n-3)--h-ch (n): blank pixels kaccc0115ec v-ch1 v-ch2 v-ch(m) h-ch1 h-ch2 start clk p1v p2v p1h p2h sg rg clamp eos trigger data video tg h-ch(n) h-ch(n-9) h-ch(n-10) h-ch11 h-ch10
ccd multichannel detector heads c7043, c7044 pin connections of "te control i/o" connector (c7044) pin no. terminal name description 1v d2 (+5 v) digital power supply 2 temp monitor analog output signal of the temperature of the ccd image sensor 3 cooling control digital input signal for starting to cool down. hcmos compatible. high level or left open: cooling low level: stand-by 4 vp (+5 v) power supply for the thermoelectric cooler in the ccd image sensor 5v f (+12 v) power supply for cooling fan 6 d.gnd ground for temperature control circuit 7 d.gnd ground for temperature control circuit 8 p.gnd power supply return of the thermoelectric cooler mounted in the ccd image sensor 9 f.gnd power supply return for cooling fan available for using same power supply (+5 v) for "+v d2 " and "+vp". caution: do not connect "vd2" and "vp" together on the backside of the 9-pin d-sub connector. these may be connected (shorted) at the power supply end, not 9-pin d-sub connector. kaccc0075ea 1 2 3 4 5 6 7 8 9 9-pin d-sub connector 5 pin connections of "signal i/o" connector kaccc0069ea 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-pin d-sub connector pin no. terminal name description 1 mode select digital input signal used to select between the line binning operation and area scanning operation. hcmos compatible. high level or left open: line binning operation low level: area scanning operation 2 data video analog video output. positive polarity. 3v a1+ (+15 v) analog power supply 4v a1- (-15 v) analog power supply 5v d1 (+5 v) digital power supply 6 start digital input signal for initializing the circuit. hcmos compatible. positive logic. the interval of the start pulses determines the integration time of the ccd image sensor. 7 clk digital input signal for operating the circuit. hcmos compatible. rising edge operation. 8 eos digital output signal for indicating end-of-scan of the image sensor. hcmos compatible. negative logic. 9 a.gnd analog ground 10 a.gnd analog ground 11 v a2 (+24 v) analog power supply 12 d.gnd digital ground 13 d.gnd digital ground 14 d.gnd digital ground 15 trigger digital output signal for a/d conversion. hcmos compatible. positive logic.
ccd multichannel detector heads c7043, c7044 6 kacca0081ec kacca0082ec dimensional outlines (unit: mm) c7043 c7044 pin connections kaccc0076eb 100.0 90.0 34.0 80.0 60.0 82.0 62.0 11.0 50.0 50.0 (4 ) m3 depth 4 focal plane focal plane 2.7 0.5 0.3 100.0 90.0 77.0 focal plane 34.0 35.0 * 80.0 60.0 82.0 62.0 11.0 50.0 50.0 focal plane (4 ) m3 depth 4 * the part is removable. 2.4 0.5 power supply v f (+12 v) f.gnd v p (+5 v) p.gnd v d2 (+5 v) d.gnd controller cooling control d.gnd te controller power supply i/o signal v d1 (+5 v) d.gnd v a1+ (+15 v) v a1- (-15 v) v a2 (+24 v) a.gnd pulse generator clk d.gnd start d.gnd controller mode select d.gnd s/h or a/d analog input a.gnd s/h input d.gnd oscilloscope ch1 gnd ext.trig gnd 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
ccd multichannel detector heads c7043, c7044 7 multichannel detector head controller c7557-01 when connected to a hamamatsu multichannel detector head and a personal computer, the c7557-01 allows easy control of the detec tor head and data acquisition by using dedicated software that comes with the unit. suitable multichannel detector head c7020/-02, c7021/-02, c7025/-02, c7040, c7041, c7043, c7044, c7180, c7181, c8061-01, c8062-01, c10150, c10151, c5964 series, c8892 accessories spare fuse (2.5 a) * 10 ac cable 2 to 3 conversion adapter usb cable detector head connection cables (for ?signal i/o? and ?te control i/o? terminal of multichannel detector head) cd-r (mcd usb driver, software, operation manual) mos adapter * 11 * 10: contained in the holder just above the ac cable connector on the c7557-01 rear panel. * 11: when operating the nmos multichannel detector head, always be sure to attach the mos adapter (supplied) to the c7557-01 mai n unit. if the the nmos multichannel detector head is connected and the power is turned on without attaching the adapter, the pow er supply in the c7557-01 main unit may be damaged. mos adapter mounting example mos bebqufs
www.hamamatsu.com information furnished by hamamatsu is believed to be reliable. however, no responsibility is assumed for possible inaccuracies or omissions. specifications are subject to change without notice. no patent rights are granted to any of the circuits described herein. ?200 9 hamamatsu photonics k.k. hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184 u.s.a.: hamamatsu corporation: 360 foothill road, p.o.box 6910, bridgewater, n.j. 08807-0910, u.s.a., telephone: (1) 908-231-0 960, fax: (1) 908-231-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 08152 -3750, fax: (49) 08152-2658 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, teleph one: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, unit ed kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: smidesv?gen 12, se-171 41 solna, sweden, telephone: (46) 8-509-031-00, fax: (46) 8 -509-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1/e, 20020 arese, (milano), italy, telephone: (39) 02-935-81-733, fax: (39) 02-935-81-741 cat. no. kacc1049e06 mar. 2009 dn ccd multichannel detector heads c7043, c7044 8 connection example ac cable (100 to 240 v; included with the c7557-01 ) pc (windows 2000/xp/vista) c7557-01 usb cable (included with the c7557-01) image sensor + multichannel detector head (usb 2.0) shutter * timing pulse dedicated cable (included with the c7557-01) * shutter, etc. are not available. te control i/o signal i/o power trig. kaccc0402ea
|
