document number acd-25c8-01 slc-an1 series lc simplex adaptor - for angle-pc - technical specifications seiko instruments inc. network components business 8, nakase 1-chome mihama-ku, chiba-shi, chiba-ken 261-8507 j apan telephone: +81-43-211-1211 facsimile: +81-43-211-8039
ii slc-an1 series lc simplex adaptor - for angle-pc - technical specifications document number acd-25c8-01 acd-25c8-01 june 2002 copyright 2002 by seiko instruments inc. all right reserved. the information contained herein shall not be reproduced or disclosed to any third party without the express written consent of sii . the specifications contained herein are subject to change without notice. sii is a trademark of seiko instruments inc. please address any questions, comments, and suggestions to: seiko instruments usa inc. electronics components division 2990 west lomita boulevard torrance, ca 90505, u.s.a. phone: +1-310-517-7780 facsimile: +1-310-517-7792 seiko instruments gmbh ofc division siemensstra?e 9b d-63263 neu-isenburg, germany phone: +49-6102-297-0 facsimile: +49-6102-297-211 seiko instruments (h.k.) ltd. sales department 4th & 5th floor, wyler center 2 200 tai lin pai road, kwai chung n.t., kowloon, hong kong phone: +852-2421-8611 facsimile: +852-2480-5479 seiko instruments taiwan inc. sales department 4f, no.40, sec. 2, min chuan e. rd., taipei 104, taiwan, r .o.c. phone: +886-2-2563-5001 facsimile: +886-2-2521-9519 seiko instruments singapore pte. ltd. component sales department 2, marsiling lane, singapore, 739144, singapore phone: +65-269-1370 facsimile: +65-269-9729
iii table of contents section page 1. provision 1 1.1 application limit 1 2. parts number 1 3. general specifications 2 3.1 parts and materials 2 3.2 physical dimensions 2 3.3 general tolerances 2 3.4 insertion loss 3 4. packing 3 5. shipping inspection 3 table table 1 parts number 1 table 2 parts and materials 2 table 3 general tolerance 2 table 4 insertion loss and measurement conditions 3 figure figure 1 insertion loss measurement system 3 figure 2 slc-an1 adaptor 4 figure 3 ! cap 5 figure 4 cut-hole dimensions 5
iv
1 1. provision 1.1 application limit these specifications apply to the slc-an1 lc simplex adaptor for angle-pc supplied by sii . 2. parts number parts number of the adaptor is shown in table 1. table 1 parts number model number type number slc-an1 slc-an1 slc-an1 slc-an1 2 2 2 22 2 2 21 1 1 10 0 0 00 0 0 0 slit sleeve 2 zirconia (required) 0 0 marking cap 1 without marking 1 white ( plastic ) 2sii
2 3. general specifications 3.1 parts and materials parts and the materials are shown in table 2. table 2 parts and materials no. part name qty material notes " housing a 1 pei green, ul94v-0 # housing b 1 pei green, ul94v-0 $ slit sleeve 1 zirconia ceramics - ! cap 2 pp white, ul94v-0 3.2 physical dimensions figure 2 shows the slc-an1 adaptor. figure 3 shows the part dimensions. figure 4 shows the cut-hole dimensions. 3.3 general tolerances permissible deviation in dimensions without tolerance indication is shown in table 3. table 3 general tolerance (jis b 0405 class m) basic size step [mm] over under permissible deviation [mm] 0.5 3 0.1 3 6 0.1 6 30 0.2
3 3.4 insertion loss specifications of insertion loss and measurement conditions are shown in table 4. figure 1 shows the measurement system. table 4 insertion loss and measurement conditions parts number slc-an1 insertion loss 0.4 db or less light source ld wave length 1.31 m conditions master cord terminated apc polishing master cord master cord light-source optical power meter photo detector master plug master plug measured adaptor figure 1 insertion loss measurement system 4. packing the product is packed to prevent damage during shipment. 5. shipping inspection insertion loss of the adaptor is inspected before shipping.
4 unit: mm figure 2 slc-an1 adaptor
5 unit: mm figure 3 ! cap unit: mm figure 4 cut-hole dimensions
|
