smt power inductors - do5010h series document 284-1 dcr srf inductance 2 max typ 3 isat 4 irms 5 part number 1 20% (h) (mohm) (mhz) (a) (a) do5010h-781ml_ 0.78 2.6 156 30 15 do5010h-152ml_ 1.5 4.0 100 25 15 do5010h-222ml_ 2.2 6.1 75 20 12 do5010h-332ml_ 3.3 8.6 60 17 10 do5010h-392ml_ 3.9 10 55 15 9.0 do5010h-472ml_ 4.7 14 40 13 8.4 do5010h-602ml_ 6.0 17 35 12 7.5 do5010h-782ml_ 7.8 18 35 11 7.5 do5010h-103ml_ 10 26 28 10 6.0 do5010h-123ml_ 12 28 26 8.5 5.2 do5010h-153ml_ 15 32 20 8.0 4.4 do5010h-223ml_ 22 47 20 7.0 3.5 do5010h-333ml_ 33 66 15 5.5 3.0 do5010h-473ml_ 47 86 9 4.5 2.6 do5010h-683ml_ 68 130 8 3.5 2.3 do5010h-104ml_ 100 190 7 3.0 1.8 do5010h-154ml_ 150 250 6 2.6 1.5 do5010h-224ml_ 220 380 5 2.4 1.2 do5010h-334ml_ 330 560 4 1.9 1.0 do5010h-474ml_ 470 850 3 1.4 0.82 do5010h-684ml_ 680 1100 2.5 1.2 0.72 do5010h-105ml_ 1000 1800 2.0 1.0 0.56 designers kit c355 contains 3 of each part core material ferrite core and winding loss see www.coilcraft.com/coreloss terminations rohs compliant tin-silver over copper. other termina - tions available at additional cost. weight 3.2 C 4.0 g ambient temperature C40c to +85c with i rms current, +85c to +125c with derated current storage temperature component: C40c to +125c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 250 per 13 reel plastic tape: 32 mm wide, 0.38 mm thick, 24 mm pocket spacing, 7.8 mm pocket depth pcb washing only pure water or alcohol recommended ? i rms ratings up to 15 a; saturation currents up to 30 a ? heavy gauge wire for low dc resistance document 284-1 revised 10/14/08 1. when ordering, please specify termination and packaging codes: do5010h-105mld termination: l = rohs compliant tin-silver over copper. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: d = 13 machine-ready reel. eia-481 embossed plastic tape. b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter d instead. 2. inductance tested at 100 khz, 0.1 vrms using an agilent/hp 4284a lcr meter or equivalent. 3. srf measured using agilent/hp 8753d network analyzer. 4. dc current at which the inductance drops 10% (typ) from its value without current. 5. current that causes a 40c temperature rise from 25c ambient. 6. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering.
document 284-2 document 284-2 revised 10/14/08 smt power inductors - do5010h series typical l vs frequency typical l vs current 0.01 0.1 11 0 1 10 100 10000 0.01 0.1 11 0 0.1 1000 inductance (h) frequency (mhz) 0.78 h 10 h 1 00 h 1 000 h 0.1 1 10 100 1000 10000 0.1 1 10 100 current (a) inductance (h) 1 00 h 10 h 1 000 h 0.78 h 0.730 18,54 0.561 14,25 0.200 5,08 max min max 0.710 18,03 0.065 1,65 max max 0.600 15,24 max note 0.500 12,70 0.250 6,35 recommended land p attern 0.626 15,90 0.075 1,90 note: maximum height : fo r -781 to -153 fo r -223 to -683 fo r -104 to -105 0.315 8,00 0.300 7,62 0.280 7,11 pa rt marking inter nal code xxx x dash n umber pa rt mar king since fe b. 2005. pa rt s manuf actured pr ior to that date ma yh ave color dots . visit www .coilcraft.com/colr po wr .cfm fo r color dot mar king details . irms derating -40 -20 02 04 06 08 0 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 25c pe r cent of rated rms i dimensions are in inches mm
|