series am ld -r z up to 1000ma | led driver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .a 1 of 3 north america only features: models single output model input voltage (v) output voltage (v) maximum rated current (ma) max capacitive load (uf) efficiency (%) ripple & noise (mv p - p) amld - 6 0 30 - r z 9 - 6 0 2 - 5 6 300 2.2 9 7 250 amld - 6 0 35 - r z 9 - 60 2 - 56 350 2.2 9 7 300 amld - 6 0 50 - r z 9 - 60 2 - 56 500 2.2 9 7 350 amld - 6060 - rz 9 - 60 2 - 56 600 2.2 97 400 amld - 6 0 70 - r z 9 - 60 2 - 56 700 2.2 9 7 400 amld - 60100 - rz 9 - 60 2 - 56 1000 2.2 97 450 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 48 9 - 6 0 vdc filter capacitor absolute maximum rating 65 vdc peak input voltage time 500 ms dc/ dc on (leave open if not used) on C open or 2.5 v< vadj < 5v dc/dc off (or short pins 2,3,4) off(shutdown) C vadj <0. 8 maximum remote pin drive current vadj = 0 - 5 v < 1 ma quiescent current in shutdown mode vin = 6 0v 3 ma on/off control (digital control ) max pwm frequency 1k hz output current adjustment 1 to 100 % output specifications parameters conditions typical maximum units current accuracy 5 % output voltage range v input = 6 0v 2 - 5 6 vdc output current vin C vout > 4 v short circuit protection regulated at the rated current for each model temperature coefficient 0.0 3 %/ o c g eneral specifications parameters conditions typical maximum units switching frequency 100 % load 40 - 1000 khz operating temperature see derating chart - 4 0 to +85 o c storage temperature - 40 to +1 25 o c maximum case temperature 1 05 o c thermal impedance free air convection + 3 0 o c /w cooling free air convection humidity 95 % rh case material non - conductive black plastic (ul94v - 0 rated) weight 1 7.7 g dimensions (l x w x h) 1.25 x 0. 8 0 x 0. 49 inches 31.75 x 20.32 x 12.45 mm mtbf > 2 000 000hrs (mil - hdbk - 217 f at +25 o c) maximum soldering temperature 1.5 mm from case for 10sec. 260 o c notes: 1. reversed polarity at the input power will damage the driver. the input ground must not be connected to the negative output. 2. maximum output open voltage is equal to input voltage. ? step down dc/dc led driver ? operating temperature range - 40o c to +85oc ? constant current output ? open and short led protection ? ultra wide ( 7 :1) input voltage range ? p wm / digital voltage di mming ? high efficiency up to 9 7 % ? output power up to 56 watts
series am ld -r z up to 1000ma | led driver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .a 2 of 3 north america only safety specifications parameters standards designed to meet en 60950 - 1 pin out specifications dimensions 31.75 (1.25) 23 22 2 3 16 14 9 11 20.32 (0.80) 4 15.24 (0.60) 2.54 (0.1) 12.45 (0.49) 5.08 (0.2) 3.00 (0.12 bottom view 22.86 (0.90) 0.50 (0.02) pin single 2 - v input - dc supply 3 - v input - dc supply 4 vadj pwm/on/off or not used 9 - v output led cathode connection 11 - v output led cathode connection 14 + v output led anode connection 16 + v output led anode connection 22 + v input + dc supply 23 + v input + dc supply mechanical tolerances case tolerance 0.25mm or 0.01 inches pin tolerance 0.05 or 0.002
series am ld -r z up to 1000ma | led driver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .a 3 of 3 north america only derating free air convection - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 safe operating area o u t p u t p o w e r ( % ) 85 ambient temperature o c amld - 6050 -rz amld - 6060 -rz amld - 6070 -rz amld- 60100 -rz 71 amld- 6030 -rz amld- 6035 -rz typical application circuits vin + vin - ( or gnd ) + 22 23 2 3 vadj ( pwm / dim / on / off ) 4 led strings 14 16 9 11 vout + vout - aimtec amld - 60 xx - rz pwm 0 v 5 v note: 1. datasheets are updated as needed and as such, specific ations are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications o n labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear cont rol systems or other such applications which necessitate specific safety and regulatory standard s other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com.
|
