do not scale from this print .285 7.24 ref .505 12.83 ref "a" "a" mmsd-05-22-x-xxxx-s shown fig. 1 ipd1-xx-d (no of pos x .100[2.54]) + .055[1.40] ref .350 8.89 ref .250 6.35 ref .100 2.54 ref 01 10 05 06 = dwc + .250[6.35] xxxx .125[3.18] section "a"-"a" dwc-xx-10-300 c1 c-179-xx-x mmsd-xx-xx-x-xx.xx-x-xxx no of positions -02 thru -25 (per row) -s: single end -d: double end(must choose from last set of options.) plating specification -f: flash selective (use c-179-xx-f) -l: light selective (use c-179-xx-l) -s: selective (use c-179-xx-s) wire gauge (awg) -20 -22 -24 -26 -28 -30 end option * -lus: latch up, straight * -lds: latch down, straight * -lux: latch up, crossed * -ldx: latch down, crossed -p: polarization(not available with -lus, -lds, -lux options ) option (see sheet 2) specify in inches [use dwc-xx-xx] (single end: 03.00 inch minimum, double end: 03.25 inch minimum) assembled length e = dwc + .250[6.35] xxxx .125[3.18] fig. 2 mmsd-05-22-x-xxxx-d shown c2 c * available on -d end option only & applies to end 2 housing sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: .100[2.54] socket discreet cable assembly by: mmsd-xx-xx-x-xx.xx-x-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 07/16/2004 2 1 sheet scale: 1.5:1 housing: nylon 66, color: white contact: phos bronze cable; insulation: pvc wire: tinned copper c:\enterprisevault\dwg\misc\mktg\mmsd-xx-xx-x-xx.xx-x-xxx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: .003[.08] max. 3. parts to be molded to position. 4. minimum pullout force: 4 lbs. 5. contact must be inserted until retention feature locks into place. 6. all finished goods are to be electical tested including hi-pot test. 7.tinned copper wire contains lead. 8. parts are to be layer packaged. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision e
-lus latch- end 1 latch- end 2 [latch up- cable straight] -lds latch- end 1 latch- end 2 [latch down- cable straight] -lux latch- end 1 latch- end 2 [latch up- cable crossed] (not available with -lus, -lds, -lux options ) -p -ldx latch- end 1 latch- end 2 [latch down- cable crossed] ipd1-xx-d-p 01 02 07 e sheet of .100[2.54] socket discreet cable assembly by: mmsd-xx-xx-x-xx.xx-x-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 07/16/2004 2 2 sheet scale: 1.5:1 revision e 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|