1 ftr-k1 series n features l 1 pole, 32a l 1 form a contact l wide contact gap: 1.5mm surge strength (b/t open contacts) 2.5kv compliant with european photovoltaic standard (vde0126) l high insulation in small package (between coil and contacts) - dielectric strength: ac 4,000v - surge strength: 6,000v l low coil power consumption: 1,200mw l plastic materials: flammability; ul94 v-0 l cadmium-free contacts l rohs compliant. please see page 5 for more information e.g.: ordering code: ftr-k3lab012w-pv actual marking: k3lab012w-pv power relay 1 pole - 32a, 1.5mm contact gap latching relay ftr-k3l-pv series n partnumber information ftr-k3l a b 012 w - pv [example] (a) (b) (c) (d) (e) (f ) (a) r elay type ftr -k3l : ftr -k3l-series (b) contact confguration a : 1 form a / pcb type (c) coil type b : s tandard sensitive (1,200mw) (d) coil r ated voltage 012 : 5.....24 vdc coil r ating table at page 3 (e) cont act material w : sil ver alloy (f) v ersion pv : high cur rent (32a) / contact gap 1.5mm
2 ftr-k1 series n specification * minimum switching loads mentioned above are reference values. please perform the confrmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. ftr-k3l-pv series item ftr-k3l-pv contact data confguration 1 form a material silver alloy resistance (initial) max. 100 m at 6vdc, 1a contact rating (resistive) 32a, 250vac max. carrying current 32a max. switching voltage 250vac max. switching power 8,000va max. switching current 32a min. switching load * 100ma, 5vdc (reference value) life mechanical min. 1 x 10 6 operations electrical resistive 32a / 250vac, min. 30 x 10 3 operations inductive 32a, 250vac (cos 0.8), 30 x 10 3 operations inductive (overload) 48a, 250vac (cos 0.8), 50 operations coil data rated power (at 20 c) 1,200mw operating temperature range -40 c to +85 c timing data set (at nominal voltage) max. 20ms (without bounce) reset (at nominal voltage) max. 20ms (without bounce) coil excitation time (at nominal voltage) min. 30ms, max. 1000ms insulation contact gap min. 1.5mm resistance min. 1,000m at 500vdc dielectric strength open contacts 2,500vac (50/60hz) 1min contacts to coil 4,000vac (50/60hz) 1min surge strength contacts to coil 6,000v / 1.2 x 50s standard wave clearance min. 6.0mm creepage min. 8.0mm other vibration resistance misoperation 10 to 55hz double amplitude 1.5mm endurance 10 to 55hz double amplitude 1.5mm shock misoperation min. 200m/s2 (11 1ms) endurance min. 1,000m/s2 (6 1ms) weight approximately 25g
3 ftr-k1 series n coil rating coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) must set voltage (vdc) * must reset voltage (vdc) * max. set/reset voltage (vdc) rated power (mw) 005 5 p 21 +4.0 - 9.0 1,200 s 21 - +4.0 006 6 p 30 +5.4 - 10.8 s 30 - +5.4 012 12 p 120 +9.6 - 21.6 s 120 - +9.6 024 24 p 480 +19.2 - 43.2 s 480 - +19.2 type compliance contact rating ul ul 508 flammability: ul 94-v0 (plastics) 32a, 277vac (general use at 60 c) csa 22.2 no.14 (by culus) vde iec61810-1 32a, 250vac (cos = 0.8) at +85 c n safety standards note: all values in the table are valid for 20c and zero contact current. * specifed operate values are valid for pulse wave voltage. ftr-k3l-pv series p: set coil s: r eset coil
4 ftr-k1 series n characteristic data ftr-k3l-pv series electrical life tests (resistive load) n dimensions l dimensions l pc board mounting hole layout (bottom view) l schematics the graphs are based on measurement data and are typical values. contacts drawn in reset condition. to operate (set), apply (+) to pin 5 and (-) to pin 2. to release (reset), apply (+) to pin 5 and (-) to pin 1. p: set coil s: reset coil
5 ftr-k1 series ftr-k3l-pv series 1. general information l all signal and power relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. l cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (ame ndment to directive 2002/95/ec) l all of our signal and power relays are lead-free. please refer to lead-free status info for older date codes at : http://www.fujitsu.com/us/downloads/micro/fcai/relays/lead-free-letter.pdf l lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise specified. this mat erial has been verified to be compatible with pbsn assembly process. 2. recommended lead free solder profile l recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity l moisture sensitivity level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. tin whiskers l dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisk er was found by our in house test. we highly recommend that you confrm your actual solder conditions flow solder condition: pre-heating: maximum 120?c soldering: dip within 5 sec. at 260?c solder bath solder by soldering iron: soldering iron temperature: maximum 360?c duration: maximum 3 sec.
6 ftr-k1 series fujitsu components international headquarter offces ftr-k3l-pv series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia pacifc fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ ?2011 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their respective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and only for general information purposes. the use of the contents, data and information provided in this datasheet is at the users own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. fujitsu components europe b.v. and affliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. nor do fujitsu components europe b.v. and affliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or ftness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. august 11, 2011
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: fujitsu: ? ftr-k3lab012w-pv? FTR-K3LAB024W-PV
|
