revision 03-05 catalog 1308028 revision 03-06 customized switching solutions customer specific applications power management modules please observe the disclaimer. 172 powertrain systems chassis systems safety security body driver information convenience 141_3d05 description features - up to 20 a load current per path at 85 ? - no power consumption (latching relay) - very compact design - two separate load circuits with common control - customer specific design on request typical applications disconnection of two power outlets in a vehicle if the battery voltage drops below a defined level please contact tyco electronics for relay application support. design dustproof; protection class ip54 to iec 529 (en 60 529); mounting bracket or mounting clip on request. delivered with cover. weight approx.1.2 oz. nominal voltage 12 v terminals quick connect terminals similar to iso 8092-1 coil and load 6.3 x 0.8 mm, surface tin-pated advantages - active power management - protection against complete dis- charging of the battery - improved ability to start the engine conditions all parametric, environmental and endurance tests are performed according to eia standard rs-407-a at standard test conditions unless otherwise noted: 23 ? ambient temperature, 20-50% rh, 29.5 1.0" hg (998.9 ?3.9 hpa). please also refer to the application recommendations in this catalog for general precautions. car industry truck industry other industry disclaimer all technical performance data apply to the relay as such, specific conditions of the individual application are not considered. please always check the suitability of the relay for your intended purpose. we do not assume any responsibility or liability for not complying herewith. we recommend to complete our questionnaire and to request our technical service. any responsibility for the application of the product remains with the customer only. all speci fications are subject to change without notification. all rights of tyco are reserved.
customized switching solutions customer specific applications power management modules please observe the disclaimer. 173 catalog 1308028 revision 03-06 revision 03-05 dimensional drawing v23141-b0001-x030 and x037 dimensional drawing v23141-b0001-x031 and x038 view of the terminal (bottom view) v23141-b0001-x030 standard pcb v23141-b0001-x037 advanced pcb view of the terminal (bottom view) v23141-b0001-x031 standard pcb v23141-b0001-x038 advanced pcb circuit diagram v23141-b0001-x030 and x037 circuit diagram v23141-b0001-x031 and x038 two separate load circuits (1-5, 2-3) with common control. two load circuits (1-5, 3-1) can be switched on separately but have common switch off. 141x30dd1 141x30vt1 141x30cd1 141x31dd1 141x31vt1 141x31cd1 terminals similar to iso-8092-6.3 x 0.8 ecu, sn plated 2...4 pm terminals similar to iso-8092-6.3 x 0.8 ecu, sn plated terminals similar to iso-8092-2.8 x 0.8 ecu, sn plated 2...4 pm terminals similar to iso-8092-9.5 x 1.2 ecu, sn plated 2...4 pm terminals similar to iso-8092-2.8 x 0.8 ecu, sn plated
customized switching solutions customer specific applications power management modules please observe the disclaimer. 174 catalog 1308028 revision 03-06 revision 03-05 coil data for v23141-b0001-x030 and v23141-b0001-x037 1) available for nominal voltages 12 v nominal power consumption continuous power on coil not allowed test voltage coil/contact 500 vac rms maximum ambient temperature range ?40 to + 105 ? set function close contacts terminals 1-5 and 2-3 connected polarity terminal 7 terminal 8 terminal 9 negative potential positive potential no current must set voltage 2) (ambient temperature 23 c) 6 v maximum set voltage (coil temperature 23 c) 22 v minimum set voltage pulse width at 6 v 5 ms maximum set voltage pulse width at 22 v 1 s resistance between 7-8 with coils at 23 c 34 4 set time (nominal voltage; coil temperature 23 c) typ. 2.5 ms reset function open contacts terminals 1-5 and 2-3 not connected polarity terminal 7 terminal 8 terminal 9 no current positive potential negative potential must set voltage (ambient temperature 23 c) 6 v maximum set voltage (coil temperature 23 c) 22 v minimum set voltage pulse width at 6 v 5 ms maximum set voltage pulse width at 22 v 1 s resistance between 8-9 with coils at 23 c 34 4 set time (nominal voltage; coil temperature 23 c typ. 2.0 ms 1) verified on single samples from serial tools. contact data contact configuration circuit symbol rated voltage rated current at 85 c standard pcb advanced pcb contact material max. switching current 1) on 2) off min. recommended load 3) voltage drop at 10 a (initial) mechanical endurance (without load) electrical endurance (tested on relay v23086-l1252-a403 used in this module) 1) the values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 v for 12 v or 27 v for 24 v load voltages. 2) for a load current duration of maximum 3 s for a make/break ratio of 1:10. 3) see chapter diagnostics in our application recommendations on page 18 of this catalog or consult the internet at http://relays. tycoelectronics.com/application.asp 2 make contacts/ 2 form a see circuit diagram 12 v one relay in use both relays in use 15 a 10 a 20 a 15 a agsno 2 50 a 30 a 1 a at 5 v typ. 15 mv, 200 mv max. > 10 6 operations resistive load: > 1 x 10 5 operations at 13.5 v on 20 a/off 20 a at +85 c on 120 ms/off 4880 ms inductive load > 1 x 10 5 operations at 13.5 v on 25 a/off 5 a at cyclic temperature on 120 ms/off 4880 ms change-40/+23/+85 c l=0.6 mh lamp load > 1 x 10 5 operations at 13.5 v on 50 a 2) /off 5 a at cyclic temperature on 120 ms/off 4880 ms change-40/+23/+85 c
customized switching solutions customer specific applications power management modules please observe the disclaimer. 175 catalog 1308028 revision 03-06 revision 03-05 coil data for v23141-b0001-x031 and v23141-b0001-x038 1) available for nominal voltages 12 v nominal power consumption continuous power on coil not allowed test voltage coil/contact 500 vac rms maximum ambient temperature range ?40 to + 105 ? set system 1 function close contacts terminals 1-3 connected polarity terminal 1 terminal 2 terminal 7 terminal 6 positive potential no current negative potential no current must set voltage (ambient temperature 23 c) 6 v maximum set voltage (coil temperature 23 c) 22 v minimum set voltage pulse width at 6 v 5 ms maximum set voltage pulse width at 22 v 1 s resistance between 1-7 with coils at 23 c 62 6 set time (nominal voltage; coil temperature 23 c) typ. 2.5 ms set system 2 function close contacts terminals 1-5 connected polarity terminal 1 terminal 2 terminal 7 terminal 6 positive potential no current no current negative potential must set voltage 2) (ambient temperature 23 c) 6 v maximum set voltage (coil temperature 23 c) 22 v minimum set voltage pulse width at 6 v 5 ms maximum set voltage pulse width at 22 v 1 s resistance between 1-6 with coils at 23 c 62 6 set time (nominal voltage; coil temperature 23 c) typ. 2.0 ms reset both systems function open contacts terminals 1-5 and 2-3 connected polarity terminal 1 terminal 2 terminal 7 terminal 6 positive potential negative potential no current no current must set voltage (ambient temperature 23 c) 6 v maximum set voltage (coil temperature 23 c) 22 v minimum set voltage pulse width at 6 v 5 ms maximum set voltage pulse width at 22 v 1 s resistance between 1-2 with coils at 23 c 31 4 set time (nominal voltage; coil temperature 23 c) typ. 2.0 ms 1) verified on single samples from serial tools.
revision 03-05 catalog 1308028 revision 03-06 customized switching solutions customer specific applications please observe the disclaimer. 176 power management modules mechanical data cover retention axial force 150 n (33.7 lbs) pull force 200 n (45 lbs) push force 200 n (45 lbs) terminals pull force 100 n (22.5 lbs) push force 100 n (22.5 lbs) resistance to bending, force applied to front 10 n (2.25 lbs) 1) resistance to bending, force applied to side 10 n (2.25 lbs) 1) torsion 0.3 nm enclosures dust cover protects relay from dust. for use in passenger compartment or enclosures 1) values apply 2 mm from the end of the terminal. when the force is removed, the terminal must not have moved by more than 0.3 mm. operating conditions temperature range, storage refer to storage in the ?lossary test relevant standard testing as per dimension comments cold storage iec 68-2-1 1000 h 40 ? dry heat iec 68-2-2 ba 1000 h + 85 ? thermal shock iec 68-2-14 na 100 cycles ?40 ?/+85 ? dwell time 15 min vibration resistance iec 68-2-6 (sine pulse form) 10-2000 hz contacts 1-5 and 2-3 closed 10 g vibration resistance iec 68-2-6 (sine pulse form) 10-500 hz contacts 1-5 and 2-3 open 6 g no change in the shock resistance iec 68-2-27 (half-sine 6 ms switching state > 10 s pulse form) up to 30 g continuous shock iec 68-2-27 eb 6 ms, 30 g, 1000 shocks in each direction drop test capable of meeting specifications after 1.0 m (3.28 foot) drop onto concrete flammability ul94-hb or better (meets fmvss 302) 2) 1) verified on separate relay samples produced in series. 2) fmvss: federal motor vehicle safety standard. ordering information part numbers contact contact enclosure special relay part number tyco order number arrangement material features 12 v modules v23141-b0001-x030 1) 1-1414255-0 see page 173 agsno2 dust cover quick connect, standard printed circuit board v23141-b0001-x037 1) 1-1414502-0 see page 173 agsno2 dust cover quick connect, advanced printed circuit board v23141-b0001-x031 2) 1-1414233-0 see page 173 agsno2 dust cover quick connect, standard printed circuit board v23141-b0001-x038 2) 1-1414501-0 see page 173 agsno2 dust cover quick connect, advanced printed circuit board 1) 7 terminals, 2 separated load circuits. 2) 6 terminals, common plus for coil and load side.
|
