do not scale from this print .120 ref 3.05 .320 8.13 ref .300 7.62 ref .025 sq ref 0.64 .100 2.54 ((no of pos -1) x .100[2.54]) .008[.20] (either direction) 2 max sway "a" "a" ipl1-xx-s c3 c2 c1 fig. 1 ipl1-106-01-xx-s shown .240 6.10 ref +.060[1.52] ref (no of pos x .100[2.54]) .100 ref 2.54 .040 ref 1.02 (no of pos -1) x .100[2.54] ref .080 ref 2.03 .010 ref 0.25 terminal offset for polarization 02 01 c l c l ipl1-1xx-xx-xx-s-xx-x row specification -s: single (use ipl1-xx-s) plating specification -f: flash selective (use t-1s64-xx-f) -l: light selective (use t-1s64-xx-l) -s: selective (use t-1s64-xx-s) -h: heavy gold (t-1s64-xx-h) -fm: flash selective/matte tin tails (use t-1s64-xx-f) -lm: light selective/matte tin tails (use t-1s64-xx-l) -sm: selective/matte tin tails (use t-1s64-xx-s) lead style -01: through hole (use t-1s64-xx-xx) -02: surface mount (see fig. 2, sht 2) (use t-1s64-xx-xx) -ra: right angle (see fig. 3, sht 3) (available with -01 lead style only) -02 thru -10 no of positions option polarization option -k: keyed polarization (use ipl1-xx-s-k) (see fig. 4, sheet 3) see note 7 .215 5.46 ref 2 max sway (typ) section "a"-"a" c5 see note 4 c4 t-1s64-07-xx c sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[0.3] 2 .xxx: .005[0.13] .xxxx: .0020[0.051] material: .100[2.54] single row terminal assembly by: ipl1-1xx-xx-xx-s-xx-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d purvis 05/02/2005 3 1 sheet scale: 3:1 standard insulator: lcp, color: black -k insulator: lcp, color: natural terminal: phos bronze f:\dwg\misc\mktg\ipl1-1xx-xx-xx-s-xx-x-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum terminal retention: 1 lb [4.45 n]. 3. parts to be molded to position. 4. post must be within .005[0.13] of each other. 5. all pin to pin dimensions to be measured from tip to tip. 6. dimension to be measured at bend. 7. tip to be flush to .015[0.38] below top of shroud. 8. note deleted. 9. package all positions. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision f
.277 ref 7.04 .010 0.25 .215 5.46 .345 8.76 90 - 4 + 0 .028 ref 0.72 t-1s64-08-xx fig. 2 [different as shown, otherwise same as fig. 1] style -02: surface mount ipl1-106-02-xx-s shown c6 see table 2 01 02 pt-1-24-01-123 pt-1-24-01-127 .115 ref 2.92 .235 5.97 t-1s64-08-xx -02: surface mount in-process 1 .277 .010 7.04 0.25 .125 3.18 90 - 4 + 0 c7 -02: surface mount in-process 2 (parts to have position #1 loaded in same direction as arrow on tube) packaging views pt-1-24-04-40 sheet of .100[2.54] single row terminal assembly by: ipl1-1xx-xx-xx-s-xx-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d purvis 05/02/2005 3 2 sheet scale: 2:1 revision f f:\dwg\misc\mktg\ipl1-1xx-xx-xx-s-xx-x-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
"b" "b" .240 6.10 ref 02 01 ipl1-106-01-xx-s-ra shown fig. 3 [different as shown, otherwise same as fig. 1] -ra: right angle .640 16.26 .115 ref 2.92 .530 13.46 ref -ra: in-process 1 t-1s64-09-xx .070 ref 1.78 .160 4.06 90 -ra: in-process 2 c8 (see note 7) .215 5.46 ref .060 1.52 (see note 6) .070 ref 1.78 section "b"-"b" t-1s64-09-xx c9 .040 1.02 ref ipl1-06-s-k fig. 4 -k: keyed polarization (ipl1-106-01-xx-s-k shown) (same as fig. 1 unless otherwise stated) sheet of .100[2.54] single row terminal assembly by: ipl1-1xx-xx-xx-s-xx-x dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d purvis 05/02/2005 3 3 sheet scale: 2:1 revision f f:\dwg\misc\mktg\ipl1-1xx-xx-xx-s-xx-x-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
