satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. opengear ? opg-1l 50 mhz C 2.3 ghz rf fiber optic link features ? 50 mhz to 2.3 ghz optimized for if- and l-band video signals ? supports 30 km links** ? optically-isolated dfb lasers enable high- dynamic-range links ? 25 db tx and rx adjustable gain range ? peak optimizer for quick and easy set-up ? smartgain for enhanced agc performance ? 50 & 75 ohm bnc or 50 ohm sma ? blind mate rf coax to support rear plug-in access ? sc/apc and lc/apc optical connectors ? tx & rx rf power monitors via led, sma, dashboard and snmp ? dashboard and snmp monitoring and control ? lnb power capable ? tx and rx pcba card and module ? 2 ru, 20-slot opengear ? enclosure ? ce & csa certifed, rohs block diagram the opg-1l was designed to be fully compatible with the opengear ? standard for terminal equip - ment or cable headend design. this means that when you install an opengear ? enclosure, you can then purchase additional insert cards from different manufacturers to be used in the same enclosure. the standard enclosure is a 19 rack-mount frame that can hold up to 20 insert cards. a separate module handles the management and control systems, and allows for local or remote interfaces. each enclosure utilizes 2 ru of rack space, maximizing the overall usage of the equipment rack. the opg-1ls rear interface modules may be pre-installed with its cabling, with - out corresponding pcba cards. this allows the user to anticipate future expansion needs without signifcantly increasing the intial investment, and without having to access the rear panel and cabling once installed. the user simply purchases corre - sponding pcba cards on an as-needed basis then slides them into place from the front of the frame, effortlessly locking them into the rear interface module. system design emcores opengear ? opg-1l rf fiber optic links are optimized to perform in the 50 mhz to 2.3 ghz frequency range providing transparent signal transport for satellite antenna applications on an open architecture platform. the opg-1l transmitter and receiver modules may be housed in the same chassis as emcores opengear ? hd video, audio, serial data and usb extension / distribution cards, allowing full monitoring and control of each module via the dashboard network management system (nms). **for higher optics, please contact us t ransmitter receiver s in push button s out p l p r s mon s mon optimizer dc to lnb photodiode laser +1 626-293-3400 ? 2013 emcore corporation | rev 2013.10 datasheet | october 2013
satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. performance highlights parameter value units tx wavelength 1310, 1550 nm optical output power 5 + 2 dbmo if-band frequency l-band frequency 50-1000 850-2300 mhz mhz frequency response any 500 mhz full band (50-2300 mhz) + 0.75 + 1.5 db db input return loss (minimum) 10 db total front-end rf gain 1 (at minimum attenuation setting) 25 + 2 db attenuation adjustment range 30 db spurs free dynamic range 2 98 db-hz 2/3 noise figure (at maximum gain, 25 c) 23 db input ip3 (at maximum gain, 25 c) -4 dbm total rf power into laser 2 + 2db dbm rx output return loss (minimum) 10 db total front-end rf gain 1 (at minimum attentuation setting) 20 (dual output) 25 (single output) db attenuation adjustment range 15 db output ip3 (at maximum gain, 25 c) 20 (dual output) 25 (single output) dbm parameter value 1 units pcba card dimension 12.8 l x 3.0 h x 0.681 w 32.5 l x 7.62 h x 0.173w in cm rear interface module dimension 1.362 l x 3.365 h x 1.31 w 3.46 l x 8.55 h x 3.33 w in cm mechanical characteristics parameter value units tx power requirement 12 w input voltage (@ 1 a max) 12 +/- 0.5 vdc lnb voltage (at rf input port, 350 ma max) 17 +/- 1.0 vdc dc current (@ +12 v with lnb off) 350 +/- 50 ma rx input voltage (@ 1 a max) 12 +/- 0.5 vdc dc current (@ +12 v) 250 +/- 50 ma electrical characteristics rear interface modules opg-1l pcba cards with rear interface modules pcba cards 1. defned per opengear development guide by ross: 8200dr-001-02, 8200dr-001-03 1. link rf gain db = tg + rg - 2*fiber loss dbo 2. sfdr = 2/3*(iip3 + 174 - nf). frame options opg-8321 og3-fr opengear ? opg-1l 50 mhz C 2.3 ghz rf fiber optic link ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. card compatibility to opengear ? frames opengear ? opg-1l 50 mhz C 2.3 ghz rf fiber optic link ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
satcom satcom-sales@emcore.com www.emcore.com information contained herein is deemed to be reliable and accurate as of the issue date. emcore reserves the right to change the design or specifcations at any time without notice. transmitter/receiver opg- wx when ordering replace w with one of the rf connector options when ordering replace x with one of the rf connector impedance options rf connector options w rf connector impedance options (ohm) x b = bnc, s = sma 5 = 50, 7 = 75 (bnc only) ordering information for rear interface module (rim) ordering information pcba card transmitter 1 receiver opg- u t- yy 05- zz opg- u r- v - zz note 1. when installing transmitter cards in the og3-fr frame, remove the pre-installed lnb blocker plug from the pcba card but leave as-is for the opg-8321 frame to prevent the frames dc-power alarm from activating. when ordering replace u with one of the frequency band options when ordering replace v with one of the rx only: rf interface options when ordering replace yy with one of the wavelength options** when ordering replace zz with one of the optical connector options frequency band options u frequency band (mhz) rx only: rf interface options v wavelength options (nm) yy output power (dbmo) optical connector options zz i = if-band 50-1000 1 = output+monitor 2 = dual outputs 13 = 1310, 55 = 1550 05 = +5 la = lc-apc, sa = sc-apc (og3-fr only) l = l-band 850-2300 1 = output+monitor 2 = dual outputs 13 = 1310, 55 = 1550 05 = +5 la = lc-apc, sa = sc-apc (og3-fr only) laser safety this product meets the appropriate standard in title 21 of the code of federal regulations (cfr). fda/cdrh class 1m laser product. this device has been classifed with the fda/cdrh under accession number 0220191. all versions of this laser are class 1m laser product, tested according to iec 60825-1:2007 / en 60825-1:2007. an additional warning for class 1m laser products. for diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifers, and microscopes) within a distance of 100 mm may pose an eye hazard. for collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. wavelength = 1.3/1.5 m. maximum power = 30 mw. *caution - use of controls or adjustments or performance of procedures other than those specifed herein may result in hazardous radiation exposure. *iec is a registered trademark of the international electrotechnical commision. opengear ? opg-1l 50 mhz C 2.3 ghz rf fiber optic link ? 2013 emcore corporation | rev 2013.10 +1 626-293-3400 datasheet | october 2013
|
