sidactor ? protection thyristors revised: 01/09/14 ? 2014 littelfuse, inc. speci?cations are subject to change without notice. baseband protection (voice-ds1) sidactor ? series, do-214 electrical characteristics sidactor ? series - do-214 sidactor ? series do-214aa are designed to protect baseband equipment such as modems, line cards, cpe and dsl from damaging overvoltage transients. the series provides a surface mount solution that enables equipment to comply with global regulatory standards. description agency agency file number e133083 agency approvals features and bene?ts t low voltage overshoot t low on-state voltage t does not degrade surge capability after multiple surge events within limit. t fails short circuit when surged in excess of ratings t low capacitance part number marking v drm @l drm =5a v s @100v/s i h i s i t v t @i t =2.2 amps capacitance @1mhz, 2v bias v min v max ma min ma max a max v max pf min pf max p0080salrp p-8a 6 25 50 800 2.2 4 25 150 p0220salrp p22a 15 32 50 800 2.2 4 25 150 p0300salrp p03a 25 40 50 800 2.2 4 15 140 p0640salrp p06a 58 77 150 800 2.2 4 40 60 p0720salrp p07a 65 88 150 800 2.2 4 35 60 p0900salrp p09a 75 98 150 800 2.2 4 25 55 p1100salrp p11a 90 130 150 800 2.2 4 30 50 p1300salrp p13a 120 160 150 800 2.2 4 25 45 p1500salrp p15a 140 180 150 800 2.2 4 25 40 p1800salrp p18a 170 220 150 800 2.2 4 25 35 P2100SALRP p21a 180 240 150 800 2.2 4 20 35 p2300salrp p23a 190 260 150 800 2.2 4 25 35 p2600salrp p26a 220 300 150 800 2.2 4 20 35 p3100salrp p31a 275 350 150 800 2.2 4 20 35 p3500salrp p35a 320 400 150 800 2.2 4 20 35 p0080sblrp p-8b 6 25 50 800 2.2 4 25 150 p0220sblrp p22b 15 32 50 800 2.2 4 25 150 p0300sblrp p03b 25 40 50 800 2.2 4 15 140 p0640sblrp p06b 58 77 150 800 2.2 4 40 80 p0720sblrp p07b 65 88 150 800 2.2 4 35 75 applicable global standards t tia-968-a t tia-968-b t itu k.20/21 enhanced level* t itu k.20/21 basic level t gr 1089 inter-building* t gr 1089 intra-building t iec 61000-4-5 t yd/t 1082 t yd/t 993 t yd/t 950 *a/b-rated parts require series resistance pinout designation schematic symbol not applicable table continues on next page. rohs
sidactor ? protection thyristors revised: 01/09/14 ? 2014 littelfuse, inc. speci?cations are subject to change without notice. baseband protection (voice-ds1) sidactor ? series, do-214 electrical parameters (continued) surge ratings series i pp i tsm 50/60 hz di/dt 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 a min a min a min a min a min a min a min a min a min a min amps/s max a2015015090507575457520 500 b 25 250 250 150 100 100 125 80 100 25 500 c 50 500 400 200 150 200 175 100 200 3 30 500 notes: 1 current wavef orm in s 2 voltage wavef orm in s 3 for surge rating of p4500sclrp 10x700s min=150a & typical=180a - peak pulse current rating (i pp ) is repetitive and guaranteed for the life of the product. - i pp ratings applicable over temperature range of -40oc to +85oc - the device must initially be in thermal equilibrium with -40c < t j < +150c part number marking v drm @l drm =5a v s @100v/s i h i s i t v t @i t =2.2 amps capacitance @1mhz, 2v bias v min v max ma min ma max a max v max pf min pf max p0900sblrp p09b 75 98 150 800 2.2 4 35 70 p1100sblrp p11b 90 130 150 800 2.2 4 30 70 p1300sblrp p13b 120 160 150 800 2.2 4 25 60 p1500sblrp p15b 140 180 150 800 2.2 4 25 55 p1800sblrp p18b 170 220 150 800 2.2 4 25 50 p2100sblrp p21b 180 240 150 800 2.2 4 20 35 p2300sblrp p23b 190 260 150 800 2.2 4 25 50 p2600sblrp p26b 220 300 150 800 2.2 4 20 45 p3100sblrp p31b 275 350 150 800 2.2 4 20 45 p3500sblrp p35b 320 400 150 800 2.2 4 20 40 p4500sblrp p45b 400 530 150 800 2.2 4 20 65 p0080sclrp p-8c 6 25 50 800 2.2 4 45 260 p0220sclrp p22c 15 32 50 800 2.2 4 30 240 p0300sclrp p03c 25 40 50 800 2.2 4 25 250 p0640sclrp p06c 58 77 150 800 2.2 4 55 155 p0720sclrp p07c 65 88 150 800 2.2 4 50 150 p0900sclrp p09c 75 98 150 800 2.2 4 45 140 p1100sclrp p11c 90 130 150 800 2.2 4 45 115 p1300sclrp p13c 120 160 150 800 2.2 4 40 105 p1500sclrp p15c 140 180 150 800 2.2 4 35 95 p1800sclrp p18c 170 220 150 800 2.2 4 35 90 p2100sclrp p21c 180 240 150 800 2.2 4 30 90 p2300sclrp p23c 190 260 150 800 2.2 4 30 80 p2600sclrp p26c 220 300 150 800 2.2 4 30 80 p3100sclrp p31c 275 350 150 800 2.2 4 30 70 p3500sclrp p35c 320 400 150 800 2.2 4 25 65 p4500sclrp p45c 400 530 150 800 2.2 4 20 65 notes: - absolute maximum ratings measured at t a = 25oc (unless otherwise noted). - devices are bi-directional.
sidactor ? protection thyristors revised: 01/09/14 ? 2014 littelfuse, inc. speci?cations are subject to change without notice. baseband protection (voice-ds1) sidactor ? series, do-214 25c case temperature (t c ) - oc 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 ratio of i h i h (t c = 2 5 oc) normalized v s change vs. junction temperature normalized dc holding current vs. case temperature i h i t i s i drm v drm v t +v -v +i -i v s 5 0 100 0 t r t d 0 peak value half value t C time (s) i pp C peak pulse c urrent C %i pp t r = rise time to peak value t d = decay time to half value waveform = t r x t d v-i characteristics t r x t d pulse waveform package symbol parameter value unit do-214aa t j operating junction temperature range -40 to +150 c t s storage temperature range -65 to +150 c r 0 ja thermal resistance: junction to ambient 90 c/w thermal considerations -8 -40 -20 0 20 40 60 80 100 120 140 160 -6 -4 0 2 4 6 8 10 12 14 junction temperature (t j ) C c percent of v s change C % 2 5 c
sidactor ? protection thyristors revised: 01/09/14 ? 2014 littelfuse, inc. speci?cations are subject to change without notice. baseband protection (voice-ds1) sidactor ? series, do-214 physical speci?cations environmental speci?cations lead material copper alloy terminal finish 100% matte-tin plated body material ul recognized epoxy meeting ?ammability classi?cation 94v-0 time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature (t 25oc to peak) ramp-down ramp-up preheat critical zone t l to t p figure 1 soldering parameters part numbering construction variable reel pack i pp rating rohs compliant type p = sidactor p x lrp median voltage package type xxx 0s high temp voltage blocking 80% rated v drm (v ac peak ) +125c or +150c, 504 or 1008 hrs. mil-std-750 (method 1040) jedec, jesd22-a-101 temp cycling -65c to +150c, 15 min. dwell, 10 up to 100 cycles. mil-std-750 (method 1051) eia/jedec, jesd22-a104 biased temp & humidity 52 v dc (+85c) 85%rh, 504 up to 1008 hrs. eia/ jedec, jesd22-a-101 high temp storage +150c 1008 hrs. mil-std-750 (method 1031) jedec, jesd22-a-101 low temp storage -65c, 1008 hrs. thermal shock 0c to +100c, 5 min. dwell, 10 sec. transfer, 10 cycles. mil-std-750 (method 1056) jedec, jesd22-a-106 autoclave (pressure cooker test) +121c, 100%rh, 2atm, 24 up to 168 hrs. eia/ jedec, jesd22-a-102 resistance to solder heat +260c, 30 secs. mil-std-750 (method 2031) moisture sensitivity level 85%rh, +85c, 168 hrs., 3 re?ow cycles (+260c peak). jedec-j-std-020, level 1 re?ow condition pb-free assembly (see fig. 1) pre heat - temperature min (t s(min) ) +150c - temperature max (t s(max) ) +200c - time (min to max) (t s ) 60-180 secs. average ramp up rate (liquidus temp (t l ) to peak) 3c/sec. max. t s(max) to t l - ramp-up rate 3c/sec. max. re?ow - temperature (t l ) (liquidus) +217c - temperature (t l ) 60-150 secs. peak temp (t p ) +260(+0/-5)c time within 5c of actual peak temp (t p ) 30 secs. max. ramp-down rate 6c/sec. max. time 25c to peak temp (t p ) 8 min. max. do not exceed +260c part marking pxxx date code part marking code (refer to electrical characteristics t able) xxxxx
sidactor ? protection thyristors revised: 01/09/14 ? 2014 littelfuse, inc. speci?cations are subject to change without notice. baseband protection (voice-ds1) sidactor ? series, do-214 package type description quantity added suf?x industry standard s do-214aa tape & reel pack 2500 rp eia-481-d packing options tape and reel speci?cation do-214aa 0.472 (12.0) 0.36 (9.2) 0.31 5 (8.0) 0.1 5 7 (4.0) 0.49 (12.4) 0. 5 12 (13.0) arbor hole dia. 12.99 (330.0) dimensions are in inches (and millimeters). direction of feed 0.0 5 9 dia (1. 5 ) cover tape dimensions do-214aa 0.079 (2.0) 0.110 (2.8) 0.079 (2.0) pad outline h k e f g a c b d case temperature measurement point inch (millimeter) dimensions inches millimeters min max min max a 0.130 0.156 3.30 3.95 b 0.201 0.220 5.10 5.60 c 0.077 0.087 1.95 2.20 d 0.159 0.181 4.05 4.60 e 0.030 0.063 0.75 1.60 f 0.075 0.096 1.90 2.45 g 0.002 0.008 0.05 0.20 h 0.077 0.104 1.95 2.65 k 0.006 0.016 0.15 0.41
|