pm2-series ? p6cg-xxxxzslf ? dual split output ? si p7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/2 p6cg-xxxxzslf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications voltage range 10% input filter capacitors input reflected ripple current1 20 ma pk-pk output specifications voltage accuracy 2% line regulation 0.4% load regulation (0% - 100%) 0.3% ripple and noise (20mhz bandwidth) 50 mv pk-pk temperature coefficient 0.02% / c general specifications efficiency see table i/o isolation voltage (3 sec.) 1000 vdc i/o isolation capacity 60 pf, typ. i/o isolation resistance 1000 m ohm switching frequency 80 khz (variable) humidity 95% rel h reliability calculated mtbf (mil-hdbk-217f) > 1.121 mhrs physical specifications case material non conductive black plastic (ul94v-0 rated) potting material epoxy (ul94v-0 rated) weight ~ 2.5g, typ. environment specifications operating temperature -25 to +71c (ambient) maximum case temperature 100c storage temperature -40 to +125c cooling free air convection (10 mm distance required) rohs conform soldering 260c, max. (1.5 mm from case 10s.) mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the pm 2 series p6cg - xxxxzslf is a family of cost effective 1 w regulated dual split output dc/dc converters. these converter s are in an ultra miniature sip7 case. devices are encapsulated. high performance features: regulated output, 1000vdc input/output is olation, high efficiency operation, output voltage accuracy of 2% maximum, input range of 10% tolerance and low output ripple and noise. pm2-series 1 watt regulated dual split output sip7 case 1 kv dc i/o isolation low ripple and noise rev.02-2009
pm2-series ? p6cg-xxxxzslf ? dual split output ? si p7 - plastic case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/2 selection guide dual split output order # i n p u t v o l t a g e ( v d c ) i n p u t c u r r e n t n o l o a d ( m a ) i n p u t c u r r e n t f u l l l o a d ( m a ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) 2 dual split output P6CG-0505ZSLF 5 28 307 5, 5 100, 100 65 100 p6cg-1205zslf 12 15 124 5, 5 100, 100 67 100 p6cg-1505zslf 15 12 99 5, 5 100, 100 67 100 p6cg-2405zslf 24 8 59 5, 5 100, 100 70 100 if you need other specifications, please enquire. package / pinning / derating modelcode datecode 1 2 4 5 6 7 6.00 (0.24) 19.50 (0.76) 15.24 (0.60) 2.54 (0.10) 0.50 (0.02) 0.50 (0.02) 2.1 (0.9) all dimensions are typical in millimeters (inches). - pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) specification may change without notice. pe a k sip 7 C plastic case # dual split 1 +vin 2 - vin 4 +v2 out 5 ground 6 + v1 out 7 omitted pin connections app notes: 1 = measured input reflected ripple current with a simu lated source inductance of 12uh. 2 = tested by minimal vin and constant resistive load. - operation under no-load conditions will not damag e these devices, but they will not observe the list ed specifications.
|
