blp40 ac-dc series data sheet 40 watts rev. dec 01, 2005 page 1 of 5 www.power-one.com features ? rohs compatible design; rohs for all six substances ? industry-standard 3? x 5? footprint ? main output remote sense ? ce marked to low voltage directive (pending) ? compliance to en61000-4-2/-3/-4/-5/-6/-8 single output model selection model nominal output min-maximum output min-maximum output peak output total ripple & noise voltage (vdc) current, convection current 1 current 2 regulation % 3 %p-p 4 blp40-1005g 5v 0 to 5a 0 to 8a 9a 2 1 blp40-1012g 12v 0 to 2.1a 0 to 3.3a 3.7a 2 1 blp40-1024g 24v 0 to 1.1a 0 to 1.8a 1.9a 2 1 triple output model selection model nominal output min-maximum output min-maximum output peak output total ripple & noise voltage (vdc) current, convection current 1 current 2 regulation % 3 %p-p 4 + 5v 0.3 to 3a 0.3 to 4a 5a 2 1 blp40-3000g +12v 0.1 to 1.5a 0.1 to 2a 3a 5 1 -12v 0.0 to 0.5a 0.0 to 0.7a 1 5 1 + 5v 0.3 to 3a 0.3 to 4a 5a 2 1 BLP40-3003G* +15v 0.1 to 1.5a 0.1 to 2a 2.5a 5 1 -15v 0.0 to 0.5a 0.0 to 0.7a 1a 5 1 * advanced product release notes: 1 10 cfm or 150 lfm (average measurement of six equally-distanced points through a 3.5? x 1.6? cross-sectional area) with power s upply mounted on 0.25? standoffs. recommended airflow direction is from the ac side to the dc side. 2 peak current duration for less than 30 sec with a maximum duty cycle of 10%. 3 at 25 c ambient including voltage set point tolerance, line, and load regulation. 4 maximum peak-to-peak noise expressed as a percentage of output voltage, 20 mhz bandwidth, and bypass capacitors of 10 f and 0.1 f . the blp40 series? economical and compact construction provides single or three-output ac-dc power conversion to meet the requirements of networking and data communications systems, as well as commercial and industrial configurations. the blp40 is rated for convection, as well as forced-air cooling. full output power is available with external forced-air cooling. other features include main-output remote sense and an internal emi filter. description
blp40 ac-dc series data sheet 40 watts rev. dec 01, 2005 page 2 of 5 www.power-one.com input specifications parameter conditions/description min nom max units input voltage - ac single-phase continuous input range. 85 100-250 264 vac input voltage - dc consult factory. input frequency ac input. 47 50/60 63 hz input current at 115vac input. 0.8 a rms inrush surge current internally limited. vin = 115vac, max power, 25 c. 18 a pk internally limited. vin = 230vac, max power, 25 c. 36 a pk input fuse internally located ac input line fuse rated at f, 250v, 3.15a. efficiency at max power. 70 % output specifications parameter conditions/description min nom max units output power with convection cooling. see model selection table 25 watts with forced-air cooling. see model selection table 40 output dc adjustability: adjustability of vo1 (vo2/vo3 are not adjustable). -5%, +10% of nom overshoot 5% load transient vo1, vo2, or vo3 deviation due to a 50 to 100% load change 3 % at a rate of 1a/s. turn-on time from ac on time required for output voltage to reach within regulation after initial application 1.5 sec of ac input. turn-on delay time required for output voltage to rise from 10% to 90%. 20 ms hold-up time at 25w, 115vac 20 ms remote sense total compensation for cable losses on vo1. 500 mv (remote sense is not available for vo2 or vo3) interface signals and internal protection parameter conditions/description min nom max units overvoltage protection main output. 5v: 5.7 6.8 12v: 13.8 16.2 v 24v: 27.6 32.4 short circuit protection fully-protected against output short circuit.
blp40 ac-dc series data sheet 40 watts rev. dec 01, 2005 page 3 of 5 www.power-one.com environmental specifications parameter conditions/description min nom max units altitude operating. 10k asl ft. non-operating. 50k asl ft. operating temperature 0 c to 70 c with linear derating to 50% above 50 c. unit will start up at 0 25 70 c -20 c, but will not meet all published specifications. storage temperature -40 85 c forced-air cooling forced-air cooling of 150 lfm at 10 cfm is required for full output power. (note 1) (see model selection table). convection cooling when unit is mounted horizontally with free-air convection. 25 w (see model selection table). temperature coefficient 0 c to 70 c (after 15-minute warm-up). 0.02 %/c relative humidity non-condensing @ 40 c 5 95 %rh shock operating: half-sine 11 3ms, 3 axis. 15 g non-operating: half-sine 113ms, 3 axis. 40 vibration operating: random vibration, 5-500 hz (10 minutes each axis). 2.4 grms non-operating: random vibration, 5-500 hz (10 minutes each axis). 6.0 grms notes: 1) 10 cfm or 150 lfm (average measurement of six equally-distanced points through a 3.5? x 1.6? cross-sectional area) with powe r supply mounted on 0.25? standoffs. recommended airflow direction is from the ac side to the dc side. safety, regulatory, and emi specifications parameter conditions/description min nom max units agency approvals ul60950-1/csa 22.2 no. 60950-1-03. en 60950-1/iec 60950-1. cb approval. ce mark for lvd. ground continuity 40 a dielectric withstand voltage input-to-ground (basic). 1500 vac 2121 vdc input-to-ouput (reinforced). the primary to secondary test is not performed 3000 vac on completed assemblies. 4242 vdc output-to-ground (functional). 500 vdc electromagnetic interference fcc part 15. conducted: b class cispr 22 and cispr 11. conducted: b esd per en61000-4-2, level 3. flicker per en61000-3-3. radiated susceptibility per en61000-4-3, level 3. 3 v/m eft/burst per en61000-4-4, level 3. 1 kv input transient protection per en61000-4-5, class 3. line-to-line: 1 kv line-to-ground: 2 rf immunity per en61000-4-6, level 3. 3 v/m magnetic fields per en61000-4-8. 1 a/m leakage current per en60950. blp40-1xxx at 264vac: 0.48 ma blp40-3xxx at 264 vac: 0.72 blp40-3003 pending approval.
blp40 ac-dc series data sheet 40 watts rev. dec 01, 2005 page 4 of 5 www.power-one.com 5.00 (127.0) 3.00 (76.2) cn4 1.23 1.07 (27.2) (2.5) 0.1 0.06 4.55 2.55 ? 0.16 (4 pl) printed circuit board fastener clearance area (4 pl) 0.27" dia (6.86) safety ground connection point #1 cn1 input connector cn2 - dc output connector (see pinout table) pin 1 vout pin 2 vout pin 3 vout pin 4 dc com pin 5 dc com pin 6 dc com top view side view end view pin 1 + sense pin 2 - sense cn2 - dc con cn3 - remote sense.con pin 1 neutral pin 2 missing pin pin 3 line cn1 - ac conn. pin #1 pin #1 safety ground connection point #2, faston tab, 0.25", 0.03" thick secondary ground cn3 - remote sense connector (approx. location) pin #1 (115.6) (64.8) (31.2) (1.5) recommended mating connectors cn1 molex 09-50-8031 08-52-0113 leoco 3940s030000 3983tcb0000 cn2 molex 09-50-8061 08-52-0113 leoco 3940s060000 3983tcb0000 cn3 molex 22-01-3027 08-52-0113 leoco 2530s020000 2533tpb0000 housing pin (4.1) overall size: 3.00" x 5.00" x 1.23" (76.2mm x 127.0mm x 31.2mm) weight: 0.51 lb (0.23 kg) mechanical drawing (single-output models) note: this is an outline drawing only. the detailed location of components is not shown.
blp40 ac-dc series data sheet 40 watts rev. dec 01, 2005 page 5 of 5 www.power-one.com 5.00 (127.0) 3.00 (76.2) 1.23 1.07 (27.2) (2.5) 0.1 0.06 4.55 2.55 ? 0.16 (4 pl) printed circuit board fastener clearance area (4 pl) safety ground connection point #1 cn1 input connector cn2 - dc output connector (see pinout table) pin 1 v2 pin 2 v1 pin 3 v1 pin 4 dc com pin 5 dc com pin 6 v3 top view side view end view pin 1 + sense pin 2 - sense cn2 - dc con cn3 - remote sense.con pin 1 neutral pin 2 missing pin pin 3 line cn1 - ac conn. pin #1 pin #1 safety ground connection point #2, faston tab, 0.25", 0.03" thick secondary ground cn3 - remote sense connector (approx. location) pin #1 (115.6) (64.8) (31.2) (1.5) recommended mating connectors cn1 molex 09-50-8031 08-52-0113 leoco 3940s030000 3983tcb0000 cn2 molex 09-50-8061 08-52-0113 leoco 3940s060000 3983tcb0000 cn3 molex 22-01-3027 08-52-0113 leoco 2530s020000 2533tpb0000 housing pin 0.27" dia (6.86) (4.1) cn4 nuclear and medical applications - power-one products are not designed, intended for use in, or authorized for use as critical c omponents in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written conse nt of the respective divisional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice. overall size: 3.00" x 5.00" x 1.23" (76.2mm x 127.0mm x 31.2mm) weight: 0.51 lb (0.23 kg) mechanical drawing (triple-output models) note: this is an outline drawing only. the detailed location of components is not shown.
|
