|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
this is information on a product in full production. june 2014 docid15817 rev 3 1/35 stp16dpps05 low voltage 16-bit constant current led sink driver with output error detection and auto power-saving datasheet - production data features ? low voltage power supply down to 3 v ? 16 constant current output channels ? adjustable output current through external resistor ? short and open output error detection ? serial data in/parallel data out ? auto power-saving ? 3.3 v mcu-driving capability ? output current: 3 to 40 ma ? 30 mhz clock frequency ? available in high thermal efficiency tssop exposed pad ? esd protection: 2 kv hbm, 200 v mm description the stp16dpps05 is a monolithic, low voltage, low current power 16-bit shift register designed for led panel displays. the device features a 16-bit serial-in, parallel-out shift register that feeds a 16-bit d-type storage register. in the output stage, sixteen regulated current sources are designed to provide 3 to 40 ma of constant current to drive the leds. the stp16dpps05 features open and short led detection on the outputs. the detection circuit checks for 3 different conditions that can occur on the output line: short to gnd, short to v o or open line. the data detection results are loaded in the shift registers and shifted out via the serial line output. the detection functionality is implemented without increasing the pin count, through a secondary function of the output enable and latch pin (dm1 and dm2 respectively). a dedicated logic sequence allows the device to enter or exit from detection mode. the stp16dpps05 output current can be adjusted through an external resistor to control the light intensity of the leds. led brightness is adjustable from 0% to 100% via the oe/dm2 pin. the auto power-shutdown and auto power-on feature allows the device to save power with no external intervention. the stp16dpps05 guarantees a 20 v output driving capability, allowing users to connect more leds in series. the high 30 mhz clock frequency makes the device suitable for high data rate transmission. the 3.3 v supply is well suited for applications which interface a 3.3 v mcu. compared to a standard tssop package, the tssop with exposed pad increases heat dissipation capability by a factor of 2.5 so-24 tssop24 tssop24 (exposed pad) qsop-24 table 1. device summary order codes package packaging STP16DPPS05MTR so-24 (tape and reel) 1000 parts per reel stp16dpps05ttr tssop24 (tape and reel) 2500 parts per reel stp16dpps05xttr tssop24 exposed pad (tape and reel) 2500 parts per reel stp16dpps05ptr qsop-24 2500 parts per reel www.st.com
contents stp16dpps05 2/35 docid15817 rev 3 contents 1 summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 pin connection and description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.2 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.3 recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 equivalent circuit and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 timing diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6 typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7 error detection mode functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1 phase one: entering error detection mode . . . . . . . . . . . . . . . . . . . . . . . . 18 7.2 phase two: error detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.3 phase three: resuming normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.4 error detection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.5 auto power-saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 10 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 docid15817 rev 3 3/35 stp16dpps05 summary description 35 1 summary description 1.1 pin connection and description figure 1. pin connection note: the exposed pad should be electrically connected to a metal land electrically isolated or connected to ground. table 2. typical current accuracy output voltage current accuracy output current v dd temperature between bits between ics 1.3 v 1% 2% 5 to 40 ma 3.3 v to 5 v 25 c summary description stp16dpps05 4/35 docid15817 rev 3 table 3. pin description pin n symbol name and function 1 gnd ground terminal 2 sdi serial data input terminal 3 clk clock input terminal 4 le/dm1 latch input terminal - detect mode 1 (see operation principle) 5-20 out 0-15 output terminal 21 oe/dm2 input terminal of output enable (active low) - detect mode 1 (see operation principle) 22 sdo serial data out terminal 23 r-ext input terminal for an external resistor for constant current programming 24 v dd supply voltage terminal docid15817 rev 3 5/35 stp16dpps05 electrical ratings 35 2 electrical ratings 2.1 absolute maximum ratings stressing the device above the ratings listed in the ?absolute maximum ratings? table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other condition above those indicated in the operating sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2.2 thermal data table 4. absolute maximum ratings symbol parameter value unit v dd supply voltage 0 to 7 v v o output voltage -0.5 to 20 v i o output current 50 ma v i input voltage -0.4 to v dd v i gnd gnd terminal current 800 ma f clk clock frequency 50 mhz t j junction temperature range (1) 1. such absolute value is based on the thermal shutdown protection. -40 to +170 c table 5. thermal data symbol parameter value unit t a operating free-air temperature range -40 to +125 c t j-opr operating thermal junction temperature range -40 to +150 c t stg storage temperature range -55 to +150 c r thja thermal resistance junction- ambient (1) 1. according with jedec standard 51-7b so-24 42.7 c/w tssop24 55 c/w tssop24 (2) exposed pad 2. the exposed pad should be soldered directly to the pcb to obtain the thermal benefits. 37.5 c/w qsop-24 55 c/w electrical ratings stp16dpps05 6/35 docid15817 rev 3 2.3 recommended operating conditions table 6. recommended operating conditions symbol parameter test conditions min. typ. max. unit v dd supply voltage 3.0 - 5.5 v v o output voltage - 20 v i o output current outn 3 - 40 ma i oh output current serial-out - +1 ma i ol output current serial-out - -1 ma v ih input voltage 0.7 v dd -v dd v v il input voltage -0.3 - 0.3 v dd v t wlat le/dm1 pulse width v dd = 3.0 v to 5.0 v 20 - ns t wclk clk pulse width 10 - ns t wen oe/dm2 pulse width 100 - ns t setup(d) setup time for data 8 - ns t hold(d) hold time for data 5 - ns t setup(l) setup time for latch 8 - ns f clk clock frequency cascade operation (1) 1. if the device is connected in cascade, it may not be possible achieve the maximum data transfer. please consider the timings carefully. -30mhz docid15817 rev 3 7/35 stp16dpps05 electrical characteristics 35 3 electrical characteristics v dd = 3.3 v to 5 v, t a = 25 c, unless otherwise specified. table 7. electrical characteristics symbol parameter test conditions min. typ. max. unit v ih input voltage high level 0.7 v dd v dd v v il input voltage low level gnd 0.3 v dd v i oh output leakage current v oh = 20 v 1 a v ol output voltage (serial-out) i ol = 1 ma 0.4 v v oh output voltage (serial-out) i oh = -1 ma v dd -0.4v v i ol1 output current v o = 0.3 v, r ext = 4 k 4.75 5 5.25 ma i ol2 v o = 0.3 v, r ext = 1 k 19 20 21 i ol3 v o = 1.3 v, r ext = 497 38 40 42 i ol1 output current error between bit (all output on) v o = 0.3 v, i o = 5 ma r ext = 4 k 1 5 % i ol2 v o = 0.3 v, i o = 20 ma r ext = 980 0.5 3 i ol3 v o = 1.3 v, i o = 40 ma r ext = 490 0.5 3 r sin(up) pull-up resistor 150 300 600 k r sin(down) pull-down resistor 100 200 400 k i dd(off1) supply current (off) r ext = 1 k , i out = 20 ma, out 0 to 15 = off 5.4 7.5 ma i dd(off2) r ext = 497 , i out = 40 ma out 0 to 15 = off 8.0 9.5 i dd(on1) supply current (on) r ext = 1 k , i out = 20 ma, out 0 to 15 = on 5.5 7.5 i dd(on2) r ext = 497 , i out = 40 ma out 0 to 15 = on 8.1 9.5 thermal thermal protection 170 c electrical characteristics stp16dpps05 8/35 docid15817 rev 3 v dd = 3.3 v to 5 v, t a = 25 c, unless otherwise specified. table 8. switching characteristics symbol parameter test conditions min typ max unit t plh1 propagation delay time, clk-outn , le/dm1 = h, oe/dm2 = l v ih = v dd v il = gnd c l = 10 pf i o = 20 ma v l = 3.0 v r ext = 1 k r l = 60 v dd = 3.3 v 53.5 86.5 ns v dd = 5 v 32 46.5 t plh2 propagation delay time, le/dm1-outn , oe/dm2 = l v dd = 3.3 v 48 75.5 ns v dd = 5 v 30 43 t plh3 propagation delay time, oe/dm2 -outn , le = h v dd = 3.3 v 71.5 118 ns v dd = 5 v 43 62 t plh propagation delay time, clk-sdo v dd = 3.3 v 15 21 31 ns v dd = 5 v 11 15 21 t phl1 propagation delay time, clk-outn , le/dm1 = h, oe/dm2 = l v dd = 3.3 v 27.5 39 ns v dd = 5 v 22 30.5 t phl2 propagation delay time, le/dm1-outn , oe/dm2 = l v dd = 3.3 v 11.5 17.5 ns v dd = 5 v 8 11.5 t phl3 propagation delay time, oe /dm2 -outn , le/dm1 = h v dd = 3.3 v 24 33.5 ns v dd = 5 v 21 28.5 t phl propagation delay time, clk-sdo v dd = 3.3 v 17.5 24 36 ns v dd = 5 v 12.5 17 25 t on output rise time 10~90% of voltage waveform v dd = 3.3 v 29 54 ns v dd = 5 v 10 17 t off output fall time 90~10% of voltage waveform v dd = 3.3 v 4.5 6 ns v dd = 5 v 3.5 5 t r clk rise time (1) 5000 ns t f clk fall time (1) 5000 ns 1. in order to achieve high cascade data transfe r, please consider tr /tf timings carefully. docid15817 rev 3 9/35 stp16dpps05 equivalent circuit and outputs 35 4 equivalent circuit and outputs figure 2. oe/dm2 terminal figure 3. le/dm1 terminal figure 4. clk, sdi terminal equivalent circuit and outputs stp16dpps05 10/35 docid15817 rev 3 figure 5. sdo terminal figure 6. block diagram % . % . & docid15817 rev 3 11/35 stp16dpps05 timing diagrams 35 5 timing diagrams note: outn = on when dn = h outn = off when dn = l figure 7. timing diagram note: 1 latch and output enable terminals are level-sensitive and are not synchronized with rising or falling edge of le/dm1 signal. 2 when le/dm1 terminal is low level, the latch circuit holds previous set of data. 3 when le/dm1 terminal is high level, the latch circuit refreshes new set of data from sdi chain. 4 when oe/dm2 terminal is at low level, the output terminals out 0 to out 15 respond to data in the latch circuits, either ?1? for on or ?0? for off. 5 when oe/dm2 terminal is at high level, all output terminals are switched off. table 9. truth table clock le/dm1 oe/dm2 serial-in out0 ............. out7 ................ out15 sdo h l dn dn ..... dn - 7 ..... dn -15 dn - 15 l l dn + 1 no change dn - 14 h l dn + 2 dn + 2 ..... dn - 5 ..... dn -13 dn - 13 x l dn + 3 dn + 2 ..... dn - 5 ..... dn -13 dn - 13 x h dn + 3 off dn - 13 timing diagrams stp16dpps05 12/35 docid15817 rev 3 figure 8. clock, serial-in, serial-out table 10. enable io: shutdown truth table clock le/dm1 sdi 0 ........... sdi 7 ............ sdi 15 sh auto power-up outn h all = l active not active (1) 1. at power-up, the device starts in shutdown mode. off l no change no change no change no change h one or more = h not active active x (2) 2. undefined. docid15817 rev 3 13/35 stp16dpps05 timing diagrams 35 figure 9. clock, serial-in, latch, enable, outputs figure 10. outputs le/dm1 oe/dm2 outn outn typical characteristics stp16dpps05 14/35 docid15817 rev 3 6 typical characteristics figure 11. output current vs. r-ext resistor table 11. output current vs. r-ext resistor r-ext ( ) output current (ma) 23700 1 11730 2 6930 3 4090 5 2025 10 1000 20 667 30 497 40 331 60 0 5000 10000 15000 20000 25000 0 10203040506070 current (ma) r external (ohm) docid15817 rev 3 15/35 stp16dpps05 typical characteristics 35 conditions: temperature = 25 c, v dd = 3.3 v; 5.0 v, i set = 3 ma; 5 ma; 10 ma; 20 ma; 50 ma; 60 ma. figure 12. i set vs. dropout voltage (v drop ) table 12. i set vs. dropout voltage (v drop ) iout (ma) avg (mv) @ 3.3 v avg (mv)@ 5.0 v 33637 57172 10 163 163 20 346 347 40 724 726 60 1080 1110 0 200 400 600 800 1000 1200 0 5 10 15 20 25 30 35 40 45 50 55 60 65 current (ma) min drop voltage (mv) avg @ 3.3v avg @ 5.0v typical characteristics stp16dpps05 16/35 docid15817 rev 3 t a = 25 c, vdd = 3.3 v; 5 v figure 13. output current vs. i ol (%) figure 14. idd on/off 0 1 2 3 4 5 6 7 8 9 10 11 12 0 5 10 15 20 25 30 35 40 45 50 55 60 65 iset (ma) idd (ma) avg idd on @ 5.0v avg idd on @ 3.3v avg idd off @ 5.0 v avg idd off @ 3.3 v docid15817 rev 3 17/35 stp16dpps05 typical characteristics 35 figure 15. power dissipation vs. package temperature note: the exposed pad should be soldered to the pcb to obtain the thermal benefits. figure 16. turn on output current characteristics (1) figure 17. turn off output current characteristics (2) electrical conditions: vdd = 3.3 v, vin = vdd, vled = 3.0 v, rl = 60 , cl = 10 pf ch1 (yellow) = oe/dm2 , ch2 (blue) = sdi, ch3 (purple) = vout, ch4 (green) = out 1. the reference level for the t on characteristics is 50% of oe/dm2 signal and 90% of output current 2. the reference level for the t off characteristics is 50% of oe/dm2 signal and 10% of output current error detection mode functionality stp16dpps05 18/35 docid15817 rev 3 7 error detection mode functionality 7.1 phase one: entering error detection mode from the ?normal mode? condition the device can switch to ?error mode? by a logic sequence on the oe/dm2 and le/dm1 pins, as shown in the following table and diagram: after these five clk cycles, the device goes into ?error detection mode? and at the rising edge of the 6th clk cycle, the sdi data are ready for sampling. table 13. entering error detection mode - truth table clk12345 oe/dm2 hlhhh le/dm1 lllhl figure 18. entering error detection mode - timing diagram clk oe/dm2 le/dm1 docid15817 rev 3 19/35 stp16dpps05 error detection mode functionality 35 7.2 phase two: error detection the 16 data bits must be set to ?1? in order for all the outputs to be on during error detection. the data are latched by le/dm1, after which the outputs are ready for the detection process. when the microcontroller switches the oe/dm2 to low, the device drives the leds to analyze if an open or short condition has occurred. the status of the leds is detected in at least 1 microsecond, and after this period the microcontroller sets oe/dm2 to high state and the output data detection result is sent to the microcontroller via sdo. error detection mode and normal mode both use the same data format. as soon as all the detection data bits are available on the serial line, the device may return to normal mode of operation. to re-detect the status, the device must first return to normal mode and reenter error detection mode. figure 19. detection diagram error detection mode functionality stp16dpps05 20/35 docid15817 rev 3 figure 20. timing example for open and/or short-circuit detection d.u.t. d.u.t. d.u.t. d.u.t. d.u.t. docid15817 rev 3 21/35 stp16dpps05 error detection mode functionality 35 7.3 phase three: resuming normal mode the sequence for reentering normal mode is shown in the following table: note: for proper device operation, the ?entering error detection? sequence must be followed by a ?resume mode? sequence, it is not possible to insert consecutive equal sequences. 7.4 error detection conditions note: where: i o = the output current programmed by the r-ext , i odec = the detected output current in detection mode figure 22. detection circuit figure 21. resuming normal mode - timing diagram clk12345 oe/dm2 hlhhh le/dm1 lllll table 14. detection conditions (v dd = 3.3 to 5 v, temperature range -40 to 125 c) configuration detect mode detection results sw-1 or sw-3b open line or output short to gnd detected ==> i odec 0.5 x i o no error detected ==> i odec 0.5 x i o sw-2 or sw-3a short on led or short to v-led detected ==> v o 2.6 v no error detected ==> v o 2.3 v 16 stp16dpps05 error detection mode functionality stp16dpps05 22/35 docid15817 rev 3 figure 23. error detection sequence ig no re on the rising edge of f irst clk pulse af ter the detection, the sdo provides the output status f eedback with the sequence out 15; out 14?out 0. in this case all the outputs are in f ault condition (open or short) this oe/dm2 pulse put the device in normal mode condition af ter edm test turn on the output with the oe/dm2 pin and wait 1 s to have the correct output status acquisition. during this time a minimum of three clk pulses are required (2 at the beginning and 1 at the end) to rewrite the shif t register. oe/dm2 and le/dm1 sequence signals to start the error detection sequence feeding 16 bit of clk signal af ter entering the edm, the sdi signal, set to 1, is loaded in the shif t register this le/dm1 pulse latch the data to the outputs docid15817 rev 3 23/35 stp16dpps05 error detection mode functionality 35 7.5 auto power-saving the auto power-saving feature minimizes the quiescent current if no active data is detected on the latches and auto powers-up the device as the first active data is latched. figure 24. auto power-saving feature conditions: temp. = 25 c, vdd = 3.3 v, vin = vdd, vled = 3.0 v, iset = 20 ma ch1 (yellow) = clk, ch2 (blue) = sdi, ch3 (purple) = le/dm1, ch4 (green) = idd idd consumption: idd (normal operation) = 2.93 ma idd (shutdown condition) = 170 a error detection mode functionality stp16dpps05 24/35 docid15817 rev 3 note: when the device goes from auto power-saving to normal operating condition, the first output that switches on shows the t on condition as seen in the plot above. figure 25. auto power-saving feature conditions: temp. = 25c, vdd = 3.3 v, vin = vdd, vled = 3.0 v, iset = 20 ma ch1 (yellow) = clk, ch2 (blue) = sdi, ch3 (purple) = le/dm1, ch4 (green) = idd docid15817 rev 3 25/35 stp16dpps05 package mechanical data 35 8 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack? specifications, grade definitions and product status are available at: www.st.com. ecopack ? is an st trademark. package mechanical data stp16dpps05 26/35 docid15817 rev 3 figure 26. qsop-24 package dimensions docid15817 rev 3 27/35 stp16dpps05 package mechanical data 35 table 15. qsop-24 mechanical data dim. mm. min typ max a 1.54 1.62 1.73 a1 0.1 0.15 0.25 a2 1.47 b 0.31 0.2 c 0.254 0.17 d 8.56 8.66 8.76 e 5.8 6 6.2 e1 3.8 3.91 4.01 e 0.635 l 0.4 0.635 0.89 h 0.25 0.33 0.41 < 8 0 package mechanical data stp16dpps05 28/35 docid15817 rev 3 figure 27. tssop24 package dimensions table 16. tssop24 mechanical data dim. mm min. typ. max. a 1.1 a1 0.05 0.15 a2 0.9 b 0.19 0.30 c 0.09 0.20 d 7.7 7.9 e 4.3 4.5 e 0.65 bsc h 6.25 6.5 k 0 8 l 0.50 0.70 docid15817 rev 3 29/35 stp16dpps05 package mechanical data 35 figure 28. so-24 package dimensions table 17. so-24 mechanical data dim. mm. min typ max a 2.65 a1 0.1 0.2 a2 2.45 b 0.35 0.49 b1 0.23 0.32 c 0.5 c1 45(typ.) d 15.20 15.60 e 10.00 10.65 e 1.27 e3 13.97 f 7.40 7.60 l 0.50 1.27 s (max.) 8 package mechanical data stp16dpps05 30/35 docid15817 rev 3 figure 29. tssop24 exposed pad dimensions 7100778_d docid15817 rev 3 31/35 stp16dpps05 package mechanical data 35 table 18. tssop24 exposed pad mechanical data dim. mm min. typ. max. a 1.20 a1 0.15 a2 0.80 1.00 1.05 b0.19 0.30 c0.09 0.20 d 7.70 7.80 7.90 d1 4.80 5.00 5.2 e 6.20 6.40 6.60 e1 4.30 4.40 4.50 e2 3.00 3.20 3.40 e0.65 l 0.45 0.60 0.75 l1 1.00 k0 8 aaa 0.10 packaging mechanical data stp16dpps05 32/35 docid15817 rev 3 9 packaging mechanical data figure 30. tssop24, tssop24 exposed pad and so-24 reel dimensions docid15817 rev 3 33/35 stp16dpps05 packaging mechanical data 35 table 19. tssop24 and tssop24 exposed pad tape and reel mechanical data dim. mm min. typ. max. a - 330 c 12.8 - 13.2 d 20.2 - n 60 - t - 22.4 ao 6.8 - 7 bo 8.2 - 8.4 ko 1.7 - 1.9 po 3.9 - 4.1 p 11.9 - 12.1 table 20. so-24 tape and reel mechanical data dim. mm. min typ max a - 330 c 12.8 - 13.2 d 20.2 - n 60 - t - 30.4 ao 10.8 - 11.0 bo 15.7 - 15.9 ko 2.9 - 3.1 po 3.9 - 4.1 p 11.9 - 12.1 revision history stp16dpps05 34/35 docid15817 rev 3 10 revision history table 21. document revision history date revision changes 05-jun-2009 1 initial release. 23-oct-2009 2 updated document status from preliminary status to final and note: on page 3 17-jun-2014 3 updated section 8: package mechanical data . added section 9: packaging mechanical data . minor text changes. docid15817 rev 3 35/35 stp16dpps05 35 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statem ents and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or register ed trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2014 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - swed en - switzerland - united kingdom - united states of america www.st.com |
Price & Availability of STP16DPPS05MTR |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |