www.pairuigroup.com page: 1 / 4 date: 12/18/2013 dc-dc converter dip-package DNV-10 series, 10watt, 2:1 input range features: 3 years warranty 1500vac isolation voltage six-side shielded metal case with low ripple and noise operating temperature range -40c to +85c over voltage, over current, short circuit protection model input voltage (vdc) output voltage (vdc) output current (ma) efficiency typ. dnv10-1211 12(9~18) 3.3 3000 85% dnv10-1212 5.1 2000 87% dnv10-1213 12.1 800 87% dnv10-1214 15.1 700 89% dnv10-1215 24.2 400 89% dnv10-2411 24(18~36) 3.3 3000 87% dnv10-2412 5.1 2000 88% dnv10-2413 12.1 800 89% dnv10-2414 15.1 700 90% dnv10-2415 24.2 400 90% dnv10-4811 48(36~72) 3.3 3000 87% dnv10-4812 5.1 2000 89% dnv10-4813 12.1 800 89% dnv10-4814 15.1 700 90% dnv10-4815 24.2 400 90% dnv10-11011 110(66~160) 5.1 2000 89% dnv10-11012 12.1 800 89% dnv10-11013 15.1 700 90% dnv10-11014 24.2 400 90% notes: 1.other input and output models may available on request; 2.you may request for the models with heatsink, plus r in th e suffix, e.g. dnv10-1211r. electrical output voltage accuracy --- 1% line regulation nominal load, full voltage 0.2% max. load regulation 20% ~ 100% rated load 0.5% max. dynamic response (transient/recovery time) 5%-50%-75% load capability ?vo/?t: 5.0%/500s
www.pairuigroup.com page: 2 / 4 date: 12/18/2013 dc-dc converter dip-package DNV-10 series, 10watt, 2:1 input range electrical ripple and noise 20mhz bm, full load 1% vout max. isolation voltage (<2ma/min) input to output 1500vac input to case 1000vac output to case 500vac isolation resistance 500vdc 20m temperature coefficient --- 0.02%/c max. operating temperature range auxiliary heat sink -40c to +85c storage temperature range --- -45c to +120c over current protection --- auto-recovery short circuit protection --- continuous auto-recovery over voltage protection --- auto-recovery relative humidity --- 10%-90% max. weight --- 20g conducted emission --- class a mtbf bellcore tr-332, 25c 2x10 5 hrs notes: unless otherwise specified, all the parameters of th e test conditions are as follows: ambient temperature 25 , the nominal input voltage, pure resistive nominal load. mechanical without heatsink with heatsink
www.pairuigroup.com page: 3 / 4 date: 12/18/2013 dc-dc converter dip-package DNV-10 series, 10watt, 2:1 input range mechanical pcb layout connection pin # single 1 +vin 2 -vin 3 +vo 4 no pin 5 gnd note: * unit is mm(inch). temperature profile capacitive loads selection vout: 3.3v 5v vout: 12v 5v vout: 24v recommended value max. value recommended value max. value recommended value max. value 10000f 15000f 1000f 2200f 470f 1000f
www.pairuigroup.com page: 4 / 4 date: 12/18/2013 dc-dc converter dip-package DNV-10 series, 10watt, 2:1 input range notes recommended test and application circuit 1. tvs&fuse will be helpful with over voltage protection and inrush limiting. recommended fuse should better be 1.5~2times of the rated current ; 2. the input filter capacitor c6 could select the aluminum el ectrolytic capacitors or tantalum capacitors, and the withstand voltage should be greater than the highest input v oltage. recommended capacitor should be between 22f~100f; 3. c1,c2 for the input filter capacitor, 0.1~1f high-frequ ency ceramics capacitor or chip capacitor are recommended. the withstand voltage of output filter c5, c7 should be great er than the highest output voltage. recommended capacitor of c7 should within 100f and c5 connected with the chip to reduce the input voltage peak, recommended 0.1~1f high-frequency ceramics capacitor or chip capacit or.
|
