benefits high voltage response, stable during most of the lifetime of the application superior voltage response during pulsing at ambient t easy integration in compact system low self-discharge rate (less than 3% after 1 year of storage at +20?) key features stainless steel container hermetic glass-to-metal sealing built-in safety vent finish with or without flat positive end non-flammable electrolyte compliant with iec 86-4 safety standard and en 50020 intrinsic safety standard underwriters laboratories (ul) component recognition (file number mh 12609) restricted for transport (class 9) main applications utility metering automatic meter readers buoys measuring equipment industrial applications professional electronics optional upon request low magnetic version november 2006 cell size references um3 - r20 - d primary lithium battery ls 33600c 3.6 v primary lithium-thionyl chloride (li-soci 2 ) high energy d-size bobbin cell (recommended for cool temperature environments) electrical characteristics (typical values relative to cells stored for one year or less at + 30? max.) nominal capacity 18.5 ah (at 1 ma + 20 c 2.0 v cut off. the capacity restored by the cell varies according to current drain, temperature and cut off) open circuit voltage (at + 20?) 3.67 v nominal voltage (at 0.7 ma + 20?) 3.6 v pulse capability: typically up to 250 ma. (250 ma/0.1 second pulses, drained every 2 mn at + 20? from undischarged cells with 10 ? base current, yield voltage readings above 3.0 v. the readings may vary according to the pulse characteristics, the temperature, and the cell's previous history. fitting the cell with a capacitor may be recommended in severe conditions. consult saft) continuous current permitting 50% of the nominal capacity to be achieved at + 20? with 2.0 v cut off. 80 ma (to maintain cell heating within safe limits. battery packs may imply lower level of maximum current and may request specific thermal protection. consult saft) storage (recommended) + 30? (+ 86?) max (for more severe conditions, consult saft) operating temperature range - 60?/+ 70? (operation above ambient t may lead to reduced capacity and (- 76?/+ 158?) lower voltage plateau readings at the beginning of pulses. consult saft) physical characteristics diameter (max) 33.4 mm (1.32 in) height (max) 60.2 or 61.6 mm (2.37 or 2.42 in) depending on finish type typical weight 90 g (3.2 oz) li metal content approx. 4.9 g available termination suffix cn, cnr radial tabs cna (ax) axial leads fl flying leads ... etc.
saft specialty battery group 12, rue sadi carnot 93170 bagnolet - france tel +33 (0)1 49 93 19 18 fax +33 (0)1 49 93 19 69 www.saftbatteries.com doc. n o 31017-2-1106 information in this document is subject to change without notice and becomes contractual only after written confirmation by saft. for more details on primary lithium technologies please refer to primary lithium batteries selector guide doc n o 31048-2. published by the communications department. photo credit: saft soci?t? anonyme au capital de 31 944 000 rcs bobigny b 383 703 873 produced by arthur associates 2.1 0.2 61.0 0.6 0.5 9.3 0.1 (on flat surface) 33.1 0.3 18.0 0.2 (on flat surface) 33.1 0.3 13.8 0.2 (on flat surface) 0.6 0.2 0.5 59.6 0.6 18.0 0.2 (on flat surface) ls 33600c 3.6 3.5 3.4 3.3 3.2 3.1 3.0 2.9 2.8 + 20c 1 10 100 - 20c 3.6 3.4 3.2 3.0 2.8 2.6 2.4 2.2 2.0 1.8 0.1 1 10 100 1000 1 0000 50 ohms/64 ma 200 ohms/17 ma 1000 ohms/3.51 ma 18.0 16.0 14.0 12.0 10.0 8.0 6.0 4.0 2.0 0 - 20 c + 20 c 1 10 100 current (ma) voltage plateau versus current and temperature (at mid-discharge) time (hours) typical discharge profiles at + 20? current (ma) restored capacity versus current and temperature (2.0 v cut off) cell voltage (v) cell voltage (v) capacity (ah) finished version with protruding positive end cap finished version with flat positive end cap dimensions in mm. storage the storage area should be clean, cool (preferably not exceeding + 30 c), dry and ventilated. warning fire, explosion and burn hazard. do not recharge, short circuit, crush, disassemble, heat above 100 c (212 f), incinerate, or expose contents to water. do not solder directly to the cell (use tabbed cell versions instead).
|
