ppm-series ? ppm40-h-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/4 ppm40-h-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 264 vac or 120 ? 370 vdc universal input frequency 47 ? 440 hz input current 115 vac at 0.86a, max ; 230 vac at 0.46a, max inrush current 115 vac at 30a, max ; 230 vac at 50a, max output specifications voltage accuracy 2% line regulation (full load) 0.5% load regulation (10-100%) 1% ripple and noise (20mhz bandwidth) 3.3, 5 vout - 50mv pk-pk, typ 12, 24 vout - 100mv pk-pk, typ short circuit protection continuous, auto resume over current protection 110-150% , auto resume over voltage protection zener diode clamp min load 1% trim 10% common specifications temperature range -40c to +70 c storage -40c to +85 c hold up time 15ms, typ . at 115vac 80ms, typ at 230vac humidity 95%, max. altitude 2000m, max switching frequency 65khz, typ i/o isolation voltage 3000vac / 1min. safety standards iec60950, en60950, ul60950 safety approvals pending safety class class ii hot swap forbid case material ul94v-0 rated install pcb cooling free air convection reliability calculated mtbf (mil-hdbk-217f) > 200,000 hrs weight ~ 250g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm - series are high efficiency green power moduls with various packaging provided by peak. the features of this se ries are: wide input voltage, dc and ac all in one, high efficiency, hig h reliability, low loss, safety isolation etc. they are widely used in industrial, office and civil equipments. ppm-series 40 watt univ. 85-264vac (120-370vdc) single output over voltage protection (out) 3 kv ac i/o isolation low ripple and noise high efficiency rev.03-2013
ppm-series ? ppm40-h-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/4 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) c a p a c i t o r l o a d ( u f ) s t a n d b y p o w e r , m a x single output ppm26-h-3r3elf 26.4 3.3 8000 78 60000 0.5w ppm40-h-05elf 40 05 8000 82 40000 0.5w PPM40-H-12ELF 40 12 3333 84 9000 0.5w ppm40-h-24elf 40 24 1667 84 2000 0.5w if you need other specifications, please enquire. package / pinning / derating 21 76 5 4 3 89.00[3.504] 81.28[3.200] 25.40 [1.000] 55.88[2.200] 55.88[2.200] 63.50[2.500] (bottom view) 25.00 [0.984] 6.00 [0.236] 1.20[0.047] (front view) all dimensions are typical in millimeters (inches). - pin diameter: 1.0 +/-0.10 (0.04 +/-0.004) - pin pitch tolerance: +/-0.35 (+/-0.014) - case tolerance +/-0.5 (+/-0.02) - specification may change without notice # single 1 ac (l) 2 ac (n) 3 + vo 4 no pin 5 - vo 6 no pin 7 trim pin connections temperature derating graph ambient temperature c 100% 40 0 100 45 55 output 70 60 30 45 70 24v output 12v output 3.3, 5v output 25
ppm-series ? ppm40-h-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/4 app notes: trim application & trim calculation application circuit for trim (part in broken line is the interior of models) 0v r 2 r 1 r 3 v ref r t trim +vot 0v r 2 r 1 r 3 v re f r t trim +vot trim up trim down formula for resistance of trim up: a= vref vot-vref r 1 r = t ar 2 r -a 2 -r 3 down: a= vref vot-vref r 2 r = t ar 1 r -a 1 -r 3 note: value for r1, r2, r3, and vref refer to the f ollowing table. r t : resistance of trim a: user-defined parameter, no actual meanings. vo(v) resistance 3.3 5v 12v 24v r1(k ) 2 3.3 3.83 8.66 r2(k ) 1.2 3.3 1 1 r3(k ) 1 1 1 1 vref(v) 1.24 2.5 2.5 2.5 vot(v) output voltage of trim, variation 10% emc emi en55022, class b ems esd iec/en 61000-4-2 6kv/8kv perf. criteria b rs iec/en 61000-4-3 10v/m perf. criteria a eft iec/en 61000-4-4 2kv (without external circuit) perf. criteria b iec/en 61000-4-4 4kv (with typical application, fig 3) surge iec/en 61000-4-5 1kv/2kv (without external circuit) perf. criteria b iec/en 61000-4-5 2kv/4kv (with typical application, fig 3) cs iec/en 61000-4-6 10 vr.m.s. perf. criteria a pfm iec/en 61000-4-8 10a/m perf. criteria a voltage dips, short and interruption immunity iec/en 61000-4-11 95% 5000ms perf. criteria b parallel lines measure ac-dc +vo -vo fu se l n 2 5 . 4 mm 2 5 . 4 mm c1 c2 1 2 . 7 mm c o p p e r sh e e t c o n n e ct oscillo g ra p h pro b e l o a d ln note: c1: 1f (ceramic capacitor) c2: 10f (electr olytic capacitor)
ppm-series ? ppm40-h-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 4/4 app notes: typical applications ppm-series fig 1 l +vo -vo l n n c2 c1 f u s e rl + tvs fig 2 l n +vo -vo ac-dc pe l n +vo -vo note: this application is not supported for this se ries. o utpu t n l n l l c m mo v1 r1 cx mo v2 mo v3 c y1 c y2 acdc fuse n tc external typical value model c1(f) c2(f) tvs ppm26-h-3r3elf 680 smbj7.0a ppm40-h-05elf 680 smbj7.0a PPM40-H-12ELF 220 smbj20a ppm40-h-24elf 1 120 smbj30a note: 1. c1 is a ceramic capacitor, it is used to filter high frequency noise. output filtering capacitors c 2 is a electrolytic capacitor, it is recommended to use high frequency and low impedance electrolytic capacitors. for capacitance and curre nt of capacitors please refer to manufacture?s datasheet. voltage derating of cap acitor should be 80% or above. tvs is a recommended component to protect post-circuits (if converter fails). 2. for standard emc requirement, please refer to fi gure 1 or figure 2 if higher emc requirement, pleas e refer to figure 3 figure 3 mov1 561kd14 mov2 mov3 561kd07 cx 0.15f/300vac; cy1 cy2 222m/400vac r1 1m /2w lcm 2mh-10mh ntc 5d-9 fuse recommended to use3.15a/250v
|
