200 watt power factor corrected supplies description the pfc200 series comprises single and multiple output models for 200 watts of continuous output power. all models have a power factor better than 0.95, and have the same mechanical dimensions and output pinning as their corresponding pu200 series models. all auxiliary outputs are with magnetic amplifier to keep regulation. the units are constructed on a printed circuit board with a u-bracket for mechanical support and heat sinking. both ?b? and ?c? versions are with ul, csa and tv approvals. features ? power factor 0.98 typical ? 90 vac to 264 vac universal input ? in compliance with en 55024, en 61000-3-2 and en 61000-3-3 ? overvoltage protection ? short-circuit protection ? power fail detect pfd signal ? 100 burn-in at full rated load ? remote sense on single output models ? compliant with rohs requirements pfc200 series safety standard approvals input specifications input voltage 90 to 264vac input frequency 47 to 63hz input current 3.6a rms for 115vac 1.8a rms for 230vac touch current 0.4ma max. @115vac, 60hz 0.8ma max. @230vac, 50hz output specifications output voltage/current: see rating chart total output power: 200 watts maximum ripple and noise: 2 peak to peak maximum overvoltage protection: provided on output #1 only; set at 112-132 of its nominal output voltage overcurrent protection: all outputs protected to short circuit conditions temperature coefficient: all outputs 0.04/ maximum transient response: maximum excursion of 4 or better on all models, recovering to 1 of final value within 500us after a 25 step load change pfd signal: ttl logic high for normal operation and ttl logic low upon loss of input power. this signal appears at least 1ms prior to +5v output dropping 5% below its nominal value. this signal also provides a minimum delay of 100ms after +5v is within regulation. 1-27 tv en60950-1 certificate no. r9955628 ul 60950-1, csa c22.2 no. 60950-1 file no. e137410 (lvd) environmental specifications operating temperature: 0 to +70 storage temperature: -40 to +85 relative humidity: 5% to 95% non-condensing derating: derate from 100% at +50 linearly to 50% at +70 cooling: 25 cfm forced air, provided on ?c? version, to be provided for ?b? version by user general specifications switching frequency: 94khz 10khz power factor: 0.98 typical efficiency: 70 minimum on all models hold-up time 12 msec minimum at 110vac line regulation: 0.5 maximum at full load inrush current: 20 amps @ 115vac or 40 amps @ 230vac, at 25 cold start withstand voltage: 3000vac from input to output 1500vac from input to ground 500vac from output to ground mtbf: 300,000 hours at full load at 25 ambient , calculated per mil-hdbk-217f emc performance (en55024) en55022: class b conducted, class b radiated fcc: class b conducted, class b radiated vcci: class b conducted, class b radiated en61000-3-2: harmonic distortion, class a and d en61000-3-3: line flicker en61000-4-2: esd, 8kv air and 4kv contact en61000-4-3: radiated immunity, 3v/m en61000-4-4: fast transient/burst, 1kv en61000-4-5: surge, 1kv dif f., 2kv com. en61000-4-6: conducted immunity, 3vrms en61000-4-8: magnetic field immunity, 1a/m en61000-4-11: voltage dips, 30 reduction for 500ms and >95 reduction for 10ms rohs
universal input pfc200 series output voltage/current rating chart maximum (1)(5) output #1 output #2 (2) output #3 output #4 (3) output model vnom. imin. imax. tol. vnom. imin. imax. tol. vnom. imin. imax. tol. vnom. imin. imax. tol. power (4) pfc200-10 5v 3.0a 40a 2% (n/a) (n/a) (n/a) 200w pfc200-12 12v 1.2a 16.7a 2% (n/a) (n/a) (n/a) 200w pfc200-13 15v 1.0a 13.4a 2% (n/a) (n/a) (n/a) 200w pfc200-14 24v 0.6a 8.4a 2% (n/a) (n/a) (n/a) 200w PFC200-16 30v 0.5a 6.7a 2% (n/a) (n/a) (n/a) 200w pfc200-18 48v 0.5a 4.2a 2% (n/a) (n/a) (n/a) 200w pfc200-23 +5v 3.0a 30a 2% +12v 0a 8a 4% (n/a) (n/a) 200w pfc200-24 +5v 3.0a 30a 2% +15v 0a 6a 4% (n/a) (n/a) 200w pfc200-25 +5v 3.0a 30a 2% +24v 0a 4a 4% (n/a) (n/a) 200w pfc200-30 +5v 3.0a 30a 2% +12v 0a 8a 4% -5v 0a 6a 4% (n/a) 200w pfc200-31 +5v 3.0a 30a 2% +12v 0a 8a 4% -12v 0a 4a 4% (n/a) 200w pfc200-32 +5v 3.0a 30a 2% +15v 0a 6a 4% -15v 0a 4a 4% (n/a) 200w pfc200-33 +5v 3.0a 30a 2% +15v 0a 6a 4% -12v 0a 4a 4% (n/a) 200w pfc200-40 +5v 3.0a 30a 2% +12v 0a 8a 4% -12v 0a 4a 4% 5v 0a 6a 4% 200w pfc200-41 +5v 3.0a 30a 2% +15v 0a 6a 4% -15v 0a 4a 4% 24v 0a 4a 4% 200w pfc200-42 +5v 3.0a 30a 2% +12v 0a 8a 4% -12v 0a 4a 4% 12v 0a 4a 4% 200w pfc200-44 +5v 3.0a 30a 2% +12v 0a 8a 4% -15v 0a 4a 4% 15v 0a 4a 4% 200w pfc200-45 +5v 3.0a 30a 2% +12v 0a 8a 4% -12v 0a 4a 4% 24v 0a 4a 4% 200w notes: 1. add suffix ?b? for u-bracket format and ?c? for enclosed format, e.g. pfc200-45c. 2. peak current is 12a on +12v, 9a on +15v and 6a on +24v. 3. output #4 is floating. it can be connected externally for positive or negative output. 4. 200 watts for ?c? version with a cover-and-fan assembly. 150 watts for ?b? version without moving air (maximum current of output #1 & #2 derated to 70%), or 200 watts with 25 cfm forced air provided by user. 5. all models may be operated at no-load. at no-load, output voltage tolerance increases to 10%. the output #1 of multiple output models requires 3a to support other outputs at their maximum rated loads. mechanical specifications notes: 1. dimension shown in inch [mm] 2. tolerance 0.02 [ 0.5] maximum 3. input connector p1 is beau inc. p/n 72-5-03c, output connector p2 is beau inc. p/n 72-5-09c, screws are #6-32 on 0.375 in centers. 4. connector p3 mates with molex housing 22-01-1043 and molex 40445 series crimp terminal. 5. connector p4 mates with molex housing 22-01-1023 and molex 40445 series crimp terminal. 6. p4 is for dc fan rated 24v/0.12a ( models pfc200-14,-16,-25),or 12v/0.2a ( other models). 7. weight: 1.30 kgs. (2.86 lbs.) approx. for ?b? version pin chart p1 p2 p3 1 2 3 1, 2 3, 4, 5 6 7 8 9 1 2 3 4 pfc200-10 pfc200-13 PFC200-16 pfc200-12 pfc200-14 pfc200-18 ac live ac neutral ac ground -sense ret. output #1 output #1 output #1 +sense fan com. ret. com. ret. pfd pfc200-23 pfc200-25 pfc200-24 ac live ac neutral ac ground output #1 com. ret. output #2 n.c. n.c. n.c. fan com. ret. com. ret. pfd pfc200-30 pfc200-32 pfc200-31 pfc200-33 ac live ac neutral ac ground output #1 com. ret. output #2 output #3 n.c. n.c. fan com. ret. com. ret. pfd pfc200-40 pfc200-42 pfc200-45 pfc200-41 pfc200-44 ac live ac neutral ac ground output #1 com. ret. output #2 output #3 output #4 return output #4 fan com. ret. com. ret. pfd conn pin model 1-28 1.50 kgs. (3.30 lbs.) approx. for ?c? version
|
