|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptroncs.com ? www.eptronics.com ? rev. 08/01/2010 75 watt - lp75w series constant voltage or constant current led driver with dimming led optimized drivers led optimized drivers led optimized drivers 1 specifications subject to change without notice custom designs available. please consult with the factory. dimming eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 75w lp75w series 1 1. ul8750, en61347, csa 22.2 safety compliant 2. fcc, 47cfr part 15 class b compliant 3. water resistant and dust proof design: ip66, nema6, for dry, damp, wet locations. 4. compact miniature, lightweight design. 5. safety isolation between primary and secondary 6. meets en61000-3-2 & en61000-3-3 class c 7. protection: output over-vol tage, output over-current, output short circuit, auto-recovery. 8. en614000-4-5: 2kv/4kv 8/20 s ec transient protection. 1. operating temperature: tc 90c maximum. reference -30 to +65c ambient 2. storage temperature range: -40 to +85c 3. humidity (non-condensing): 5% - 95%rh 4. cooling: convection 5. vibration frequency: 5-55hz/2g, 30 minutes 6. impact resistance: 1g/s 7. mtbf@ 40 o c: 474,000 hours @ full load per mil-217f notice 2. input voltage range: 90 to 305vac frequency: 47- 63hz power factor: > 0.90 at > 75% load, 120vac/230vac/277vac 50/60hz thd%: < 20% at > 60% load, 120vac/230vac/277vac 50/60hz inrush current: <50a at 25c, 277v, cold start, max. load input current: 1.0a maximum efficiency: 86% typical at 230vac full load constant current regulation: +/ -2% over input line variation load regulation accuracy: +/-3% leakage current: 400ua typical; hold up time: half cycle constant current versions e325626 ip66 drive mode: constant current or constant voltage technology: pfc corrected 2-stage switch mode output power: 75w max. input voltage: 90 to 305vac, 47- 63hz number of outputs: one output voltages: 4vdc - 214vdc output currents: 350ma - 6250ma optional 0-10v or pwm positive dimming 10% ~ 100% environmental electrical specifications at 25 o c safety and compliance model: lp75w series 1. typical efficiency measured at 230vac input, full load 2. for dimmable versions add approp riate designator to the end of the part number: for example: lp75w-15-c5000-rd is 0-10v or r esistance dimmable version, lp75w-15-c5000-pd is pwm dimmable version. -rd 0-10v & resistance dimmable version comes with an extra two wires +purple/-grey on the output side. -pd pwm dimmable version comes with an extr a two wires +purple/-grey on the output side. 3. -rd 0-10v dimming is compatible with most quality 0-10v wall dimmers and direct 0-10v analog signal. see page 3 for details. 4. -pd pwm version is pwm dimmable via a pos itive 10% to 100% duty cycle, 500hz to 1.5khz, 0-10v pulse. see page 4 for details. notes part number (2) us class 2 cn class 2 output voltage range output constant current current accuracy output power maximum typical efficiency (1) lp75w-214-c0350 no no 72 - 214 vdc 350 ma + 3% 75w 91% lp75w-166-c0450 no no 56 - 166 vdc 450 ma + 3% 75w 91% lp75w-108-c0700 no no 36 - 108 vdc 700 ma + 3% 75w 90% lp75w-72-c1050 no no 24 - 72 vdc 1050 ma + 3% 75w 90% lp75w-54-c1400 yes no 18 - 54 vdc 1400 ma + 3% 75w 88% LP75W-48-c1560 yes no 16 - 48 vdc 1560 ma + 3% 75w 88% lp75w-42-c1790 yes no 14 - 42 vdc 1790 ma + 3% 75w 86% lp75w-36-c2100 yes yes 12 - 36 vdc 2100 ma + 3% 75w 86% lp75w-27-c2800 yes yes 9 - 27 vdc 2800 ma + 3% 75w 85% lp75w-24-c3130 yes yes 8 - 24 vdc 3130 ma + 3% 75w 85% lp75w-20-c3750 yes yes 7 - 20 vdc 3750 ma + 3% 75w 84% lp75w-15-c5000 yes yes 5 - 15 vdc 5000 ma + 3% 75w 84% lp75w-12-c6250 no no 4 - 12 vdc 6250 ma + 3% 75w 84%
eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 2 led optimized drivers led optimized drivers led optimized drivers 30 watt - ld30w series constant voltage or constant current led driver with dim- ming 75 watt - lp75w series constant voltage or constant current led driver with dimming constant voltage versions labeling example mechanical dimensions: inches [mm] material: black aluminum housing fully encapsulated weight: 19 oz ( 538 grams) typical part number us class 2 cn class 2 output constant voltage output current range voltage accuracy output power maximum typical efficiency (1) lp75w-214 no no 214 vdc 88 - 350 ma + 5% 75w 91% lp75w-166 no no 166 vdc 113 - 450 ma + 5% 75w 91% lp75w-108 no no 108 vdc 175 - 700 ma + 5% 75w 90% lp75w-72 no no 72 vdc 263 - 1050 ma + 5% 75w 90% lp75w-54 yes no 54 vdc 350 - 1400 ma + 5% 75w 88% LP75W-48 yes no 48 vdc 390 - 1560 ma + 5% 75w 88% lp75w-42 yes no 42 vdc 448 - 1790 ma + 5% 75w 86% lp75w-36 yes yes 36 vdc 525 - 2100 ma + 5% 75w 86% lp75w-27 yes yes 27 vdc 700 - 2800 ma + 5% 75w 85% lp75w-24 yes yes 24 vdc 783 - 3130 ma + 5% 75w 85% lp75w-20 yes yes 20 vdc 938 - 3750 ma + 5% 75w 84% lp75w-15 yes yes 15 vdc 1250 - 5000 ma + 5% 75w 84% lp75w-12 no no 12 vdc 1563 - 6250 ma + 5% 75w 84% eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 led optimized drivers led optimized drivers led optimized drivers specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 3 75 watt - lp75w series constant voltage or constant current led driver with dimming -rd 2-wire 0-10v ccr dimming scheme parameters minimum typical maximum source current out of 0-10v purple wire 0ma ? 2ma absolute voltage range on 0-10v (+) purple wire -2.0v ? +15v sink current into 0-10v purple wire 0ma ? 1.2ma notes 1. -rd 0-10v dimmable version comes with an extra two wires +purple/-grey on the output side. 2. -rd version is compatible with most 0-10v wa ll slide dimmers and direct 0-10v analog signal. recommended wall slide dimmer is leviton ip710 or equivalent 3. -rd 0-10v dimmable version is not intended to dim below about 5% @ 0v or 10% @ 1.0v 4. -rd 0-10v dimmable version output will be 100% with purple/grey open and minimum with purple/grey shorted. dim (-) grey lp75w-xx-cxxxx-rd dim (+) purple dim (-) grey lp75w-xx-cxxxx-rd dim (+) purple v -rd 2-wire resistance dimming scheme -rd 2-wire 0-10v analog dimming scheme ip710 wall dimmer 0-10v sink eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 4 led optimized drivers led optimized drivers led optimized drivers 30 watt - ld30w series constant voltage or constant current led driver with dim- ming 75 watt - lp75w series constant voltage or constant current led driver with dimming -pd 2-wire ccr pwm positive dimming scheme parameters minimum typical maximum absolute maximum voltage range on pwm input (purple wire) -2.0v 10v +15v input low level voltage range (purple wire) -2.0v 0v +5.5v input high level voltage range (purple wire) +9.0v 10v +15v current into pwm input (purple wire) 0ma ? 1.2ma source current out of pwm input (purple wire) 0ma ? 2ma pwm input signal positive duty cycle 0% 10-90% 100% pwm input signal frequency 500hz ? 1500hz 1. -pd pwm dimmable version comes with an ex tra 2 wires +purple/-grey on the output side. 2. -pd pwm dimmable version is not intended to dim below about 5% @ 0% duty cycle or 10% @ 10% duty cycle 3. -pd pwm dimmable version output will be 100% with pu rple/grey open and minimum with purple/grey shorted. notes lp75w-xx-cxxxx-pd pwm (+) purple pwm (-) grey pwm in sink -pd 2-wire pwm positive dimming scheme eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 led optimized drivers led optimized drivers led optimized drivers specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 5 75 watt - lp75w series constant voltage or constant current led driver with dimming parameter min. typ. max. notes/conditions input voltage 90 vac ?? 305 vac 120, 230, 240, 277 vac nominal values input frequency 47 hz ?? 63 hz 50/60hz nominal input ac current ?? ?? 0.71 a measured at 120vac/60hz input, output full load. ?? ?? 0.40 a measured at 230vac/60hz input, output full load. inrush current (peak) ?? 42a 50a measured at 277vac/60hz input, output full load, ta 25 o c, cold start 50% ipeak duration ~ 750 sec (1/2*ip 2 *t) inrush current (i 2 t) ?? ?? 0.94 a 2 s leakage current ?? ?? 0.28ma measured at 120vac/60hz input, output full load. ?? ?? 0.78ma measured at 277vac/60hz input, output full load. thd ?? ?? 20% measured at 120, 230, 277vac input, output > 60% load power factor (pf) 0.90 ?? ?? measured at 120, 230, 277vac input, output > 75% load input specifications parameter min. typ. max. notes/conditions dc output voltage per table ?? per table per tables on page 1 dc output constant current -3% per table +3% per tables on page 1 output power ?? ?? per table per tables on page 1 ripple & noise (vpk-pk) ?? ?? 5% vo 20 mhz bw, full load output in parallel with 0.1 f ceramic & 10 f electrolytic. ripple (ipk-pk) ?? ?? 5% io 20 mhz bw, full load output in parallel with 0.1 f ceramic & 10 f electrolytic. 120 hz component (flicker free) start-up time ?? 200 ms 1000 ms measured at 120vac/60hz input, output full load. hold-up time ?? 40 ms ?? typical @ 277vac input, output full load. output specifications parameter min. typ. max. notes/conditions case temperature (tc) -30 o c ?? +90 o c measured at location specified on case. operating temperature (ta) -30 o c ?? +60 o c this is a reference range. tc controls temperature range. storage temperature (ts) -40 o c ?? +85 o c non operating temperature range. operating humidity ?? ?? 95% rh relative humidity, non-condensing. vibration 5 hz ?? 55 hz 2g, 10 minutes/1 cycl e, period 30 minutes, each along x, y, z axis. mtbf 474,000 hours ?? ?? mil-hdbk-217f notice 2, ta = 25c, output full load. environmental specifications parameter min. typ. max. notes/conditions output short circuit (scp) ?? ?? ?? no dam age, auto recovery after short is removed. output over current (ocp) ?? ?? +8% io constant current limiting circuit. output over voltage (ovp) ?? ?? 120% vo no damage, auto recovery after fault is removed. protection specifications eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 6 led optimized drivers led optimized drivers led optimized drivers 30 watt - ld30w series constant voltage or constant current led driver with dim- ming 75 watt - lp75w series constant voltage or constant current led driver with dimming safety notes/standards ul/cul ul8750 & can/csa-22.2 no. 250.13-12, ul1310 & can/csa-22.2 no. 223-m91 for class 2, ul1012/csa-c22.2 no. 107.1 for non class 2 ce en61347-1, en61347-2-13 withstand voltage input to output: 3750 vac isolation resistance input to output: >100 m ? , 500vdc @ 25 o c, 70 % rh dimming circuit dim+ purple/dim- grey are considered part of the secondary circuit. safety compliance standard notes/conditions fcc, 47cfr part 15 class b en 55015 limits and methods of measurement of radio disturbance characteristics of el ectrical lighting and similar equipment . en 61000-4-5 part 4-5: surge immunity test, 2 kv l-n, 4 kv l-fg & n-fg energy star energy star transient protection: ballast or driver shall comply with ansi/ieee c62.41.1-2002 and ansi/ieee c62.41.2-2002, category a operation. the line transient shall consist of seven strikes of a 100 khz ring wave, 2.5 kv level, for both common mode and differential mode. en 61000-3-2 part 3-2: limits for har monic current emissions class c, > 80% rated power en 61000-3-3 part 3-3: limitation of voltage changes, voltage fluctuations and flicker. emc compliance power factor curves (typical) pf vs. output power 0.700 0.750 0.800 0.850 0.900 0.950 1.000 33% 60% 80% 100% output power power factor 90v/60hz 120v/60hz 230v/50hz 277v/60hz eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 led optimized drivers led optimized drivers led optimized drivers specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 7 75 watt - lp75w series constant voltage or constant current led driver with dimming thd curves (typical) efficiency curve (typical) ld40w-36-c1100-rd thd vs. output power 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 33% 60% 80% 100% output power total harmonic distortion 90v/60hz 120v/60hz 230v/50hz 277v/60hz spec efficiency vs. output power 70.00% 75.00% 80.00% 85.00% 90.00% 95.00% 100.00% 33% 60% 80% 100% output power efficiency 90v/60hz 120v/60hz 230v/50hz 277v/60hz ty p. eptronics, inc. ? los angeles, california ? t: 800 643-0688 ? e: sales@eptronics.com ? www.eptronics.com ? rev a1.2 - 01/27/2014 specifications subject to change without notice custom designs available. please consult with the factory. dimming 75w lp75w series 8 led optimized drivers led optimized drivers led optimized drivers 30 watt - ld30w series constant voltage or constant current led driver with dim- ming 75 watt - lp75w series constant voltage or constant current led driver with dimming life vs. ambient temperature life vs. case (tc) temperature |
Price & Availability of LP75W-48 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |