www. belling .com .cn 1 30 0ma bi - d irection r elay d riv er BL8023C description BL8023C is a bi - direction relay drive r circuit, used to control the magnetic latching relay, with large output capability , ultra - low power consumption . it can be widely used in smart meters and other pulses, level control applications . BL8023C can provide 30 0ma typical driving current, which will different according to the relay coil resistance. the input high level threshold of BL8023C is 3 v ; it can compatible with most single chip microcontroller . BL8023C is available in so p - 8 package. features ? 5 to 36 v input voltage range ? low power consumption (iq<1ua) ? input high level threshold : 3 v , compatible with most single chip microcontroller ? typical driving current: 3 0 0ma rds(on)=15ohm(vin=12v, pmosfet+nmosfet) rds(on)=10ohm(vin=20v, pmosfet+nmosfet) ? peak d riving c urrent: 500ma@vin=24v ? environment temperature: - 4 0 ? c ~85 ? c ? so p - 8 package applications ? smart meter typical application ordering information part no. package BL8023C sop - 8 pin out & marking so p - 8 note 8023s: product code ll lll : 4 th to 8 th digits of lot no. BL8023C 8 0 2 3 s l l l l l o a n c a g n d v i n b n c o b r e l a y a b l c 5 2 2 3 2 2 0 v a c a c v + r s 1 2 3 4 5 6 7 8 a c v - l n + b r i d g e
www. belling .com .cn 2 BL8023C absolute maximum rating parameter value max input voltage 40 v max operating junction temperature(tj) 1 50 ? c ambient temperature(ta) - 4 0 ? c C 12 5 ? c package thermal resistance sop - 8 ja 128 ? c / w jc 45 ? c / w storage temperature(ts) - 40 ? c - 150 ? c lead temperature & time 260 ? c , 10s note: exceed these limits to damage to the device. exposure to absolute maximum rating conditions may affect device reliability. r ecommended work conditions parameter value input voltage range max. 36 v operating junction t emperature(tj) - 4 0 ? c C 8 5 ? c electrical characteristics ( vdd=5v, t a =25 ? c ) symbol parameter conditions min typ max unit v in input voltage range 5 36 v iq quiescent current 1 ua rdson switch rdson vin=12v, r l =75ohm 1 2 18 ohm vin=30v, r l =75ohm 10 16 ohm vin=12v, r l = 40 ohm 12 18 ohm vin=30v, r l = 40 ohm 10 16 ohm v th o n input high voltage vin=12v 3 v r in equivalent input resistor 500 kohm v sd fly - wheel d iode forward voltage is=1a 0.8 1.5 v t r rise time v in =12v, r l = 75 ohm 40 ns t d(on) turn on delay time vin=12v, r l =75ohm 60 ns t f fall time vin=12v, r l =75ohm 30 ns t dioff) turn off delay time vin=12v, r l =75ohm 70 ns logic function table input a input b output oa output ob relay response 1 0 1 0 on 0 1 0 1 off 0 0 high - impedance high - impedance hold 1 1 high - impedance high - impedance hold
www. belling .com .cn 3 BL8023C pin description pin # name description 1 oa output a 2 , 6 nc not connected. 3 a input a 4 gnd ground. 5 ob output b 7 b input b 8 vin supply input voltage electrical performance tested under ta=25 ? c , unless otherwise specified turn on delay and rise time turn off delay and fall time ch1 --- input ch2 --- output ch1 --- input ch2 --- output 0 100 200 300 400 500 600 700 800 900 0.0 0.5 1.0 1.5 2.0 i(ma) v sd (v) forward voltage 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 5 10 15 20 25 30 35 40 vth(v) vin(v) vth vs. vin
www. belling .com .cn 4 BL8023C block diagram detailed description pulse triggering if input is driven by square pulse, connect the inputs to the pulse source directly. relay will operate as logic table stated (vin should be less than the power supply voltage, rs is current - limiting resistor, it can be ignored in the voltage is below 20v, i.e. rs=0). the recommended pulse width=100ms. the length of the intervals should be longer than 100ms. these intervals include: intervals between forwar d drive pulse and next backward drive pulse, intervals between forward drive pulse and next forward drive pulse, intervals between backward drive pulse and next forward drive pulse, intervals between backward drive pulse and next backward drive pulse. i nputa inputb pulse width =100m s pulse w idth =100m s interval interval forward drive/open backward drive/close inputa inputb pulse width =100m s interval forward drive/open forward drive/open pulse width =100m s interval
www. belling .com .cn 5 BL8023C pulse triggering application diagram level triggering i f i nput is driven by voltage level, resist or r1, r2 should be used to insure low voltage standby input. apply input voltage according to logic table drives the relay corresponding ly (r1, r2=30k - 100k, r3, r4=100k, c1, c2=10n, recommended for removing input spikes ; vin should be less than the power supply vo ltage, rs is current - limiting resistor, it can be ignored in the voltage is below 20v, i.e. rs=0) . level triggering application diagram BL8023C BL8023C a b v i n r 1 c 1 r 3 v i n r 2 r 4 r e l a y l c 5 2 2 3 2 2 0 v a c a c v + r s 1 2 3 4 5 6 7 8 a c v - l n b r i d g e +
www. belling .com .cn 6 BL8023C package outline package so p - 8 devices per reel 25 00 unit mm package specification:
|
