maf00030dem MN103SE5 series type mn103sfe5p internal rom type flash rom (byte) 624k ram (byte) 32k package (lead-free) lqfp048-p2-0707a minimum instruction execution time 20.9 ns (at 3.0 v to 3.6 v, 48 mhz) ? interrupts reset. irq 3 . timer 12. i 2 c 7. sif 8 . dma 12 . stream dma 1 . wdt. system error. usb 2. i2s 1 ? timer counter 8-bit timer 6 reload-down count. cascade connection possible (usable as a 16-bit to 32-bit timer) 16-bit timer 2 up-down count. input capture. pwm output. compare/capture register 2 channnels watchdog timer 1 ? serial interface multi-master i 2 c 2 uart/synchronous interface selective 4 ? audio output interface i2s interface 1 ? dma controller number of channels: 4 channels unit of transfer: 8/16/32 bits maximum transfer cycles: 65535 starting factor: external interrupt. timer. serial transmission/reception. i 2 c transmission/reception. software. usb transmission/reception end. i2s empty transfer method: 2-bus cycle transfer adressing modes: fixed. increment. decrement transfer mode: word transfer. burst transfer. intermittent transfer ? stream dma controller number of channels: 1 channels unit of transfer: 8/32 bits maximum transfer cycles: 65535 transfer source: interface ram transfer destination: serial i/f. audio output interface ? usb host controller conforms to usb 2.0: full-speed (12 mbps) supported ohci r1.0a standard conforming. external power supply control function. usb transceiver built-in ? i/o pins i/o 27 : (3 v i/o) common use
maf00030dem mn103sfe5p ? pin assignment lqfp048-p2-0707a p81, tm10ioa, scl5 p82, tm10iob, sda5 p84, tm 11 iob, sbo1, bck a p85, tm6io, sbi1, srda ta a p86, tm7io, sbt1, lrclka p33, sbo3, sda3 p34, sbi3 p35, sbt3, scl3, clk0 p92, sbt0, bckb p90, sbo0, srda ta b p91, sbi0 vdd3 vdd3 vdd3 vdd1 8 vs s vppe x nrst vddi pd4, irq1 pd2, sbt2 pd1, sbi2 pd0, sbo2 pd5, irq2, lrclkb mmod 1 mmod 0 vddi, vout vdd 3 osco osci av dd usbd+ av ss usbd- usbnpp , usbpp , pc 1 usbnoc, pc 0 ocd_sda ocd_scl p00, extrg 0 p01, extrg 1 p02, trcclk p03, trcst vss p04, trcd0 p05, trcd1 p06, trcd2 p07, trcd3 p83, tm1 1ioa, irq3, mclk 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 36 35 34 33 32 31 30 29 28 27 26 25 37 38 39 40 41 42 43 44 45 46 47 48
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20080805
|
