module photosensor amplifier digital output function, current-to-voltage conversion amplifier for amplifying very slight photocurrent with low noise c9329 c9329 is a current-to-voltage conversion amplifier used to amplify very slight photocurrent from a photodiode with very low noi se. three ranges of photocurrent detection sensitivity level (h, m, l) are selectable to match the input signal. c9329 operates on the built-in dry batteries so it can be easily used anywhere. c9329 can be directly connected to a personal computer through the rs-232c interface allowing you to a cquire high- resolution (16-bit) digital output signals and use the data logger function. features applications l three sensitivity ranges h : 1 10 9 (v/a) m: 1 10 7 (v/a) l : 1 10 5 (v/a) l selectable operation modes (analog output / digital output) l serial connection (rs-232c) with pc l data logger function, low battery function l operates on either dry battery or ac adapter l precision photometry l laser monitors l optical power meters l low signal current preamplifiers 1 absolute maximum ratings (ta=25 c) parameter symbol value unit maximum supply voltage vcc max. +14 v operating temperature * 1 topr 0 to +50 c storage temperature * 1 tstg -10 to +60 c *1: no condensation electrical and optical characteristics (ta=25 c) parameter symbol condition min. typ. max. unit h - 1 10 9 - m - 1 10 7 - conversion impedance l rf -1 10 5 - v/a h 0 - 5 m 0 - 500 input photo current range l ic 0 - 50000 na hdc16- m dc 1.6 k - frequency bandwidth (-3 db) l fc dc 1.6 k - hz offset drift - *2 - - 0.5 mv/day temperature drift - - - 25 v/ c maximum output amplitude v fs r l =2 k ? 5 - - v output noise vn frequency bandwidth * 3 - - 0.5 mv p-p output resistance ro - 100 - ? maximum input capacitance ct overshoot 30 % max. - - 5000 pf analog output (manual mode) maximum capacitive load c l - - 1000 pf interface - rs-232c, 19200 bps, 8-bit, non-parity, 2-stop bit - a/d conversion voltage range - 5 v digital output (remote mode) a/d read cycle - - 50 - ms consumption current is * 4 - - 20 ma battery lifetime - r l > 10 k ? * 4 -50-hr *2 without photodiode. maximum output variation per day, measured at 25 c after 10-minute warm-up after power on. *3 analog output measured after amplified 10 times (through 1.6 khz low-pass filter). *4 without photodiode. when using one alkaline dry battery 6lr61 (006p, 9 v) in analog output.
photosensor amplifier c9329 this is an example using a photodiode whose cathode is internally connected to its metal package. when you use a photodiode metal package, use an insu- lator to electrically insulate and also hold the package in a shield case as shown in the figure at right. connect the anode to the shield case. any single-element photodiode with a terminal capaci- tance below 5000 pf can be used. using a photodiode with anode grounded is recom- mended. using a photodiode with a bnc connector (s2281 se- ries) allows you to easily make measurements because it connects to c9329 with a bnc-bnc plug coaxial cable. kaccc0221ea typical connection to photodiode 2 anode: connect to the shield wire of the cable and shield case. cathode: connect to the core wire of the cable. solder insulator cathode anode photodiode external shield case coaxial cable with bnc plug connect to c9329 terminal connection example operation example by digital output (remote mode) coaxial cable with bnc-bnc plug photodiode (s2281 series) to rs-232c terminal pc to in terminal to dc terminal ac adapter (need not be connected when operating on battery) switch c9329 rear sw to "remote mode" rs-232c cable rf range switch kaccc0222ea display example of accessory sample software data logger setting range measurement interval: 50 ms to 1 min (50 ms interval) measurement count: 32000 max. measurement interval meassurement count: 20 hours max. dimensional outline (unit: mm, excluding project parts) accessories ? ac adapter (plug type: a-2 plug) * 5 ? dry battery ? sample software cd-rom (os: windows 7 * 6 ? instruction manual *5: caution) depending on the country, an adapter plug might be required when connecting to the ac outlet. if so, please purchase a proper adapter plug from an electronics supply house. *6: resistered trademark of microsoft corporation in the united states. photodiode, coaxial cable with bnc-bnc plug and rs-232c cable are not supplied with c9329. you will need an rs-232c cable (straight cable terminated with a d-sub 9 pin female connector at both ends) available from electronics supply houses. kacca0137ea upper surface rear manual mode dc jack dc12v eiaj rs232c only for remote modes remote mode out in 90 ?1 115 ?1 40 ?1 front rf range h m l zero adj. data log. photosensor amplifier c9329 power on auto zero push start note: use the rf range switch to change the detection sensitivity. (detection sensitivity cannot be changed from the pc.)
s2281 series photodiodes are sealed in a metal package with a bnc connector and designed to connect to c9329 photosensor amplif ier. two different spectral response ranges are provided. the large active area makes s2281 series suitable for optical power meters. a variant type s9219 with a visual compensation filter is also available.hamamatsu also provides e2573 bnc-bnc coaxial cable (length: 1 m) as an option. photodiode si photodiode si photodiode with bnc connector s2281 series 0.1 190 400 600 800 1000 0.3 0.2 (typ. ta = 25 ?c) 0.4 0.5 0.6 0.7 photo sensitivity (a/w) wavelength (nm) s2281/-04 s2281-01 general ratings parameter s2281 s2281-01 s2281-04 unit active area size 11.3 11.3 7.98 mm active area 100 100 50 mm 2 package metal with bnc connector - w indow material quartz glass - absolute m axim um ratings parameter symbol s2281 s2281-01 s2281-04 unit reverse voltage v r max. 5 v o p eratin g tem p erature topr -10 to +60 c storage temperature tstg -20 to +70 c electrical and optical characteristics (ta=25 c, unless otherwise noted) s2281 s2281-01 s2281-04 parameter s y mbol condition min. t yp . max. min. t yp . max. min. t yp . max. unit spectral res p onse ran g e - 190 to 1100 -- 190 to 1000 -- 190 to 1100 -nm peak sensitivit y wavelength p - 960 - - 720 - - 960 - nm =200 nm 0.10 0.12 - 0.10 0.12 - 0.10 0.12 - photo sensitivit y s = p - 0.5 - - 0.36 - - 0.5 - a/w short circuit current isc 100 lx 64 80 - 32 40 - 32 40 - a dark current i d v r =10 mv - 50 500 - 6 300 - 50 500 pa shunt resistance rsh v r =10 mv 20 200 - 30 1700 - 20 200 - m ? rise tim e tr v r =0 v r l =1 k ? -3- -7- -3- s terminal capacitance ct v r =0 v f=10 khz - 1300 - - 3200 - - 1300 - pf noise e q uivalent power nep v r =0 v, = p - 1.8 10 -14 -- 8.6 10 -15 -- 1.8 10 -14 -w/hz 1/2 25.0 0.1 17.5 0.1 7.98 10.0 0.1 16.0 +0 - 0.1 5.0 0.2 glass window 25.0 0.1 17.5 0.1 11.3 active area (100 mm 2 ) active area (50 mm 2 ) s2281,s2281-01 s2281-04 ) ( bnc : ug-625b/u core: cathode case: anode kspda0080ea dimensional outline (unit: mm) spectral response kspdb0090ea 3
cat. no. kacc1100e04 jul. 2014 dn www.hamamatsu.com hamamatsu photonics k.k., solid state division 1126-1 ichino-cho, higashi-ku, hamamatsu city, 435-8558 japan, telephone: (81) 53-434-3311, fax: (81) 53-434-5184 u.s.a.: hamamatsu corporation: 360 foothill road, p.o.box 6910, bridgewater, n.j. 08807-0910, u.s.a., telephone: (1) 908-231-0960, fax: (1) 908-231-1218 germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49) 8152-375-0, fax: (49) 8152-265-8 france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, telephone: 33-(1) 69 53 71 00, fax: 33-(1) 69 53 71 10 united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, united kingdom, telephone: (44) 1707-294888, fax: (44) 1707-325777 north europe: hamamatsu photonics norden ab: thorshamnsgatan 35 16440 kista, sweden, telephone: (46) 8-509-031-00, fax: (46) 8- 509-031-01 italy: hamamatsu photonics italia s.r.l.: strada della moia, 1 int. 6, 20020 arese, (milano), italy, telephone: (39) 02-935-81-733, fax: (39) 02-935-81-741 china: hamamatsu photonics (china) co., ltd.: 1201 tower b, jiaming center, no.27 dongsanhuan beilu, chaoyang district, beijing 100020, china, telephone: (86) 10-6586-6006, fax: (86) 10-6586-2866 product specifications are subject to change without prior notice due to improvements or other reasons. this document has been carefully prepared and the information contained is believed to be accurate. in rare cases, however, there may be inaccuracies such as text errors. before using these products, always contact us for the delivery specification sheet to check the latest specifications. type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(x)" which means preliminary specifications or a suffix "(z)" which means developmental specifications. the product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. however, even if within the warranty period we accept absolutely no liability for any loss caused by natural d isasters or improper product use. copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. information described in this material is current as of july, 2014.
|
