user's ma nual r20ut2220 ej02 00 rev. 2 .00 page 1 of 8 mar 05, 201 4 r0e5563 n edmb00 debugging mcu board for 144 - pin 0.5mm - pitch lqfp of the rx6 3n and rx6 31 group s 1. overview the debugging mcu board R0E5563NEDMB00 (hereafter referred to as ?this product?) is for mcus of the rx63n and rx631 group s in the plqp0144ka -a package . w ith the e20 emulator, the emulator occupies some user port pins for controlling the emulator and output of trace information . these user port pins must be connected with a 38 - pin connector installed on the user system. w ith th is product , however, all us er port pins are available for the user system . in addition, you do not need to install a 38-pi n connector on the user system. figure 1 shows the configuration of a system that includes this product and the e20. be sure to read section 7, notes on usage, b efore using this product . debugging mcu board (this product) yqpack (provided with this product) nqpack (provided with this product) e20 emulator user system 38-pin connector host computer usb interface cable figure 1 system configuration 2. package components the package of this product consists of the following items. check that you have all of th e components when you unpack the box. table 1 package components component quantity remarks debugging mcu board common part ( r0e5563nevkz00 ) 1 for the dimensions, refer to section 6 , dimensions of t h is prod u ct . converter board (r 0e55630epfk00 ) 1 for the dimensions, refer to section 6 , dimensions of t h is prod u ct . yqpack144sd (from toky o eletech corporation) 1 connector to be placed between this product and the nqpack. nqpack144sd - nd (from tokyo eletech corporation) 1 ic socket for mounting on the user system yq - guide - s1 (from tokyo eletech corporation) 4 screws for fastening the yqp ack to the nqpack. cautions in handling 1 cautions when handling the products of tokyo eletech corporation user?s manual (english and japanese) 1 for each this manual (english) note: nqpack, yqpack, yqsocket, yq - guide, hqpack, tqpack, tqsocket, cssocke t, csplug/w, and lspack are trademarks of tokyo eletech corporation . r20ut 2220 ej02 00 rev.2 .00 mar 05 , 201 4
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 2 of 8 mar 05, 201 4 important caution caution to be taken for disposal: penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation. european union regulatory notices: the weee (waste electrical and electronic equipment) regulations put responsibilities on producers for the collection and recycling or disposal of electrical and electronic waste. return of weee under these regulations is applicable in the european union only. this equipment (including all accessories) is not intended for household use. after use the equipment cannot be disposed of as household waste, and the weee must be treated, recycled and disposed of in an environmentally sound manner. renesas electronics europe gmbh can take back end of life equipment, register for this service at http://www.renesas.eu/weee . caution s to be taken for handling t his p roduct : ? take full care not to touch any parts or cause short circuits on th is product. ? protect this product from excessive physical shock. ? do not alter this product. if any alteration is attempted, this product will no longer be supported. ? the mcu installed on this product is only for use in debugging. do not remove the mcu from the board to use it for other purposes. ? for purchasing the nqpack144sd -nd, yqpack144sd and hqpack144sd , contact the following: tokyo eletech corporation http://www.tetc.co.jp/e_index.h tm cautions to be taken for turning on the power : ? do not apply a power voltage that is beyond the range guaranteed for the mcu. ? only supply power to this product and connected parts after having connect ed all cables. caution for use temperature: t his product is to be used in an environment with a maximum ambient temperature of 35c. care should be taken that this temperature is not exceeded. european union regulatory notices this product complies with the following eu directive . environmental compliance and certification : ? waste electrical and electronic equipment (weee) directive 2012/19/ec
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 3 of 8 mar 05, 201 4 3. specifications table 2 shows the functional specifications of this product . table 2 specification s of t his product item no. item specification 1 mcu for use ? rx63 n - and rx631 - g roup mcus in plqp0144ka - a packages 2 the mcu type name installed on th is product ? r5f563neddfc (rom: 2 m bytes, ram: 128 kbytes, e2 data flash : 32 kbytes ) 3 power supply ? power (vcc = avcc0 = vrefh = vcc_usb) at 2 . 7 *1 to 3.6 v is supplied from the us er system. ? power (vrefh0) at 2.7 to avcc0 is supplied from the user system. ? power ( vbat t) at 2.3 to 3.6 v is supplied from the user system. ? the state of power supply can be monitored through the test pins ( tp1 for vrefh0, tp2 for avcc0, tp3 for vrefh, tp4 for vbatt, tp5 for vcc_usb, tp6 for vcc, and tp7 for gnd ). 4 system clock (extal) ? 4 to 1 6 mhz c lock signal s are supplied from the user system. 5 sub clock (xcin) ? 32.768 k hz clock signals are supplied from the user system. note*: 1. u se th is pr oduct at a voltage (vcc > v por ) that doesn't make the mcu enter the state of power on reset. 4. reset circuit figure 2 shows the reset circuit, with the level on the res # pin pulled up by a 510- k? resistor. 38-pin connector (cn3) pin 9 (res#) *1 mcu (ic1) res# yqsocket144sdf (ic1) pin 19 (res#) *2 r9 0 uvcc r8 510k notes*: 1. the number indicated is the pin number of the 38-pin connector (cn3). 2. the number indicated is the pin number of the yqsocket144sdf (ic1). r0e5563nevkz00 r0e55630epfk00 figure 2 reset circuit
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 4 of 8 mar 05, 201 4 5. connection to connect th is product and the user system, follow the procedure below. the R0E5563NEDMB00 (this product) can be used for debugging and on - board evaluation in common by mounting the nqpack144sd -nd on the user system. (1) for debugging 1. mount the nqpack144sd - nd on the user system. be sure to check that the location of pin 1 is correct. 2. install the yqpack144sd after checking for a match with the position of pin 1 for the nqpack144sd - nd. then use the yq - guide - s1 to affix the yqpack144sd to the nqpack144sd - nd. do not use the screws included with the yqpack144sd for fixing the yqpack144sd. do not use the screwdriver included with the nqpack144sd - nd for fixing the yq - guide - s1. that is used only for the hqpack144sd. note that you need to provide your own screwd river. 3. connect the R0E5563NEDMB00 after checking for a match with the position of pin 1 for the yqpack144sd. 4. install the connector of the flexible cable from the e20 emulator to the 38 - pin connector on the R0E5563NEDMB00. hold the R0E5563NEDMB00 whi le connecting the cable to avoid imposing heavy pressure on the 38 -pin connector of the R0E5563NEDMB00. (2) for on - board evaluation 5. mount an mcu with on - chip flash memory and the hqpack144sd ( not included ) in order on the nqpack144sd -nd on the user s ystem. before using the R0E5563NEDMB00 , be sure to read section 7, notes on usage . warning warnings to be taken for connection: ? always switch off the emulator, this product , and the user system before connecting or disconnecting the emulator. fail ure to do so will create a fire hazard and will damage the emulator, this product , and the user system. ? make sure that the connectors on both ends of the user - system interface cable are facing the right way relative to the u ser - side connector on the emul ator and the 38 - pin connector on this product , respectively . incorrect connection will create a fire hazard and will damage the emulator, this product , and the user system. caution caution s to be taken for mount ing the nqpack: ? check the locations of pin 1 before mounting the nqpack. ? the tightening torque must be no greater than 0.054 n?m. if the applied torque is not accurately measurable, stop tightening when the force required to turn the screw (yq - guide - s1) becomes significantly greater than that required at the start of tightening. tightening a screw too much may break the screw hole of the nqpack or lead to a faulty connection by cracking solder on the nqpack side. ? failure of conduction during operation may be due to a crack in the solder for the nqpack. check conduction with a tester and re - solder the nqpack as required. yqpack 144sd use a flat - bladed screwdriver. 144- pin , 0.5- mm pitch ( plqp 0144 ka-a) foot pattern nqpack 144 sd- nd yq- guide -s1(4) 2 3 1 (1 ) for debugging (2 ) for on - board evaluation 4 r0e 55630 epfk 00 ( back side : yqsocket 144 sdf) 5 flexible cable of the e 20 emulator r0e 5563 nevkz 00 r0e 5563 nedmb 00 hqpack 144 sd ( not included ) mcu indicates pin 1 in this example . check that the pin -1 positions on the foot pattern and all of the components are correctly aligned . 38- pin connector figure 3 con nection s of the user system and this product
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 5 of 8 mar 05, 201 4 6. dimensions of this product figures 4 shows the dimensions and reference foot pattern of th is product (R0E5563NEDMB00). 1 44 133 45 88 89 132 unit[mm] 19.00 23.00 19.00 23.00 0.50 0.25 0.50x35=17.50 r0e5563nevkz00 rev.a tp6 50.00 50.00 x1 power tp7 gnd cn3 1 37 2 38 tp5 tp4 tp3 tp2 tp1 vcc vbatt avcc0 vrefh vrefh0 vcc_usb ic1 18.30 10.50 10.50 25.00 25.00 10.50 10.50 176 figure 4 reference foot pattern and dimension s of th is product (R0E5563NEDMB00)
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 6 of 8 mar 05, 201 4 7. notes on usage read the following warnings before using this product . incorrect operation will damage this product and the user system. the user program will be lost. notes on connecting the d ebugging mcu board : ? cable s must not be connected or removed while the power is on. ? before connecting this product and the user system, check that the pin 1 locations on both sides are correctly aligned with each other. note on rewriting the flash memory: ? the number of times tha t the flash memory in the mcu installed on this product can be programmed is limited. if an error in erasure occurs during debugging, replace this product . notes on debugging : ? t his product is only usable for debugging when it is connected to the user sy stem. ? debugging by this product alone is not supported. notes on starting the debugger and selecting the mcu type: ? select the mcu type for use in the device name section of the [initial settings] dialog box on initiation of the debugger. note on differ ences between the mcu to be debugged and this product : ? the rom size of the mcu installed in this product is 2mb . note that if the rom size of the mcu to be debugged is smaller than that of this product, access can be made to the differential area . notes on designing the user system: ? pull the levels on the emle pin down to 4.7 k to 10 k. ? p ull the levels on the md pin up to 4.7 k to 10 k, and select the single - chip mode. ? the output of the reset circuit of the user system must be open collector. note on the flash programming software products ( flash development toolkit , renesas flash programmer , etc.) : ? do not use the flash programming software products when using this product . note on the writing the o n - chip f lash m emory m ode : ? if the debugger has an exclusive mode for flash writing (e.g. ?writing the on - chip flash memory mode? of high - performance embedded workshop), do not use the mode. note on the a/d c onverter: ? the characteristics of the a/d converter differ from those of actual mcu because t here are a converter board and other devices between the mcu and the user system. note on the hot plug - in f unction : ? do not use the hot plug - in function when using this product . note on the use of a l ow cl crystal resonator for the sub - clock oscillator: ? note that the longer sub - clock wiring pattern resulting from the use of this product may cause a failure in sub - clock oscillation or affect the oscillating accuracy. note on communication interface : ? use this product via jtag communication .
R0E5563NEDMB00 user's manual r20ut2220 ej02 00 rev. 2 .00 page 7 of 8 mar 05, 201 4 precau tions this product is only intended for use in a laboratory environment under ambient temperature and humidity conditions. a safe separation distance should be used between this and any sensitive equipment. its use outside the laboratory, classroom, study area or similar such area invalidates conformity with the protection requirements of the electromagnetic compatibility directive and could lead to prosecution. the product generates, uses, and can radiate radio frequency energy and may cause harmful int erference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipmen t off or on, you are encouraged to try to correct the interference by one or more of the following measures; ? ensure attached cables do not lie across the equipment ? reorient the receiving antenna ? increase the distance between the equipment and the receiver ? connect the equipment into an outlet on a circuit different from that which the receiver is connected ? power down the equipment when not i n use ? consult the dealer or an experienced radio/tv technician for help note: it is recommended th at wherever possible shielded interface cables are used. the product is potentially susceptible to certain emc phenomena. to mitigate against them it is recommended that the following measures be undertaken; ? the user is advised that mobile phones sho uld not be used within 10m of the product when in use. ? the user is advised to take esd precautions when handling the equipment. this product does not represent an ideal reference design for an end product and does not fulfi l l the regulatory standards for an end product. 8. warranty 1. this product comes with a one - year warranty after purchase. should the product break down or be damaged while you?re using it under normal condition based on its user?s manual, it will be repaired or replaced free of cost. 2. note, however, that if your product's fault or damage is raised by any one of the following causes, the warranty is void. a) m isuse or abuse of the product or its use under other abnormal conditions b) i mproper handling of the product after purchase, s uch as dropping of the product when it is transported or moved c) o ther pieces of equipment connected to the product d) f ire, earthquakes, thunderbolts, floods, or other natural disasters or abnormal voltages, etc. e) m odifications, repairs, adjustments, or other acts made to the product by other than r enesas electronics corporation. in the above cases, contact your local distributor. if your product is being leased, consult the leasing company or the owner.
notice 1. descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of renesas electronics or others. 4. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of renesas electronics product. 5. renesas electronics products are classified according to the following two quality grades: "standard" and "high quality". the recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. renesas electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). you must check the quality grade of each renesas electronics product before using it in a particular application. you may not use any renesas electronics product for any application for which it is not intended. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for which the product is not intended by renesas electronics. 6. you should use the renesas electronics products described in this document within the range specified by renesas electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas electronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 7. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design. please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compatibility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. renesas electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. you should not use renesas electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. when exporting the renesas electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. it is the responsibility of the buyer or distributor of renesas electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, renesas electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of renesas electronics products. 11. this document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of renesas electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this document or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-owned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. http://www.renesas.com refer to "http://www.renesas.com/" for the latest and detailed information. renesas electronics america inc. 2880 scott boulevard santa clara, ca 95050-2554, u.s.a. tel: +1-408-588-6000, fax: +1-408-588-6130 renesas electronics canada limited 1101 nicholson road, newmarket, ontario l3y 9c3, canada tel: +1-905-898-5441, fax: +1-905-898-3220 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-651-700, fax: +44-1628-651-804 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-65030, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 301, tower a, central towers, 555 langao rd., putuo district, shanghai, china tel: +86-21-2226-0888, fax: +86-21-2226-0999 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 13f, no. 363, fu shing north road, taipei, taiwan tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 80 bendemeer road, unit #06-02 hyflux innovation centre singapore 339949 tel: +65-6213-0200, fax: +65-6213-0300 renesas electronics malaysia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petaling jaya, selangor darul ehsan, malaysia tel: +60-3-7955-9390, fax: +60-3-7955-9510 renesas electronics korea co., ltd. 12f., 234 teheran-ro, gangnam-gu, seoul, 135-080, korea tel: +82-2-558-3737, fax: +82-2-558-5141 sales offices ? 2013 renesas electronics corporation. all rights reserved. colophon 3.0 renesas tools website http:// www .renesas.com/tools all trademarks and registered trademarks are the property of their respective owners. if the requ irements shown in the "caution" sentences are ignored, the equipment may cause personal injury or damage to the products. ? 2012 - 201 4 renesas electronics corporation and renesas solutions corp. colophon 3.0
|
