View BD521GOFJ-E2_8502341.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ac/dc drivers ac/dc controller ic for led lighting bd521gofj general description bd5 21go fj is a n ac/dc converter for led lighting . this ic can be applied to q uasi - resonant typed h igh -s ide led driver application, and the high current precision and l ow em i noise can be achieved. moreover, owing to the built - in pfc (power factor correction) converter, the harmonic is improved. by choosing the external mosfet, the led driver s for from low power to high power can be achieved. so that, it can be widely used on from the low power lighting such as spotlight to the high power lighting such as base light. o wing to the external current setting resistance, a power supply design with a high degree of freedom can be achieved. key specification s ? operating p ower s upply v oltage r ange : vcc 8.9v to 2 5 .0v ? operating current : normal o peration : 400 a (typ ) ? o perat ing t emperature r ange : - 40 c to +10 5c features ? quasi - resonant s witching m ode + pfc c ircuit ? non - isolated a pplication ? maximum f requency 30 0khz ? vcc p in: u nder v oltage p rotection ? vcc p in: o ver v oltage p rotection (l atch ) ? cs p in: leading - edge - blanking f unction ? cs p in: open protection f unction ? led over current detection f unction package w (typ ) x d (typ ) x h(max) sop - j8 4.90mm x 6.00mm x 1.65mm application led b ulb, d own - light , tube l ight etc. electrical m achinerie s for led l ighting typical application circuit l1 cb cin d1 dz1 c3 rs co u1 c2 led+ led- ro r4 d2 r3 r2 c1 l2 f1 da1 lpf comp gnd out chg vcc cs zt rout dout vin q1 r1 dz2 q2 figure 1 . application c ircuit product structure : silicon monolithic integrated circuit this product has no designed protection against radioactive rays . 1/ 16 tsz02201 - 0f4f0c300100 -1-2 20 . apr .2016 rev.00 2 www.rohm.com ? 2016 rohm co., ltd. all rights reserved. tsz22111 ? 14 ? 001 datashee t downloaded from: http:///
b d521gofj absolute maximum ratings ( ta=25 c) item symbol rating unit condition input v oltage r ange 1 vmax1 - 0.3 to 30 v vcc , chg input v oltage r ange 2 vmax2 - 0.3 to 6.5 v cs , comp , l p f, zt input v oltage r ange 3 vmax3 - 0.3 to 15 .5 v out operating t emperature r ange t opr - 40 to +105 o c maximum j unction t emperature tjmax 150 o c storage t emperature r ange t st g - 55 to +150 o c caution: operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider c ircuit protection measures, such as adding a fuse, in case the ic is operated over the absolute maximum ratings. thermal resistance ( note 1) parameter symbol thermal resistance (typ ) unit 1s ( note 3) 2s2p ( note 4) sop - j8 junction to ambient ja 149.3 76.9 c /w junction to top characterization parameter ( note 2 ) jt 18 11 c /w (note 1) based on jesd51 - 2a(still - air) (note 2) the thermal characterization parameter to report the difference between junction tem perature and the temperature at the top center of the outside surface of the component package. (note 3) using a pcb board based on jesd51 - 3. (note 4) using a pcb board based on jesd51 - 7. layer number of measurement board material board size single fr -4 114.3mm x 76.2mm x 1.57mmt to p coppe r pattern thickness footprints and t races 70 m layer number of measurement board material board size 4 layers fr -4 114.3mm x 76.2mm x 1.6mmt to p 2 internal layers bottom copper pattern thickness copper pattern thickness copper pattern thickness footprints and traces 70 m 74.2mm x 74.2mm 35 m 74.2mm x 74.2mm 70 m recommended operating condition ( ta=25 c) item symbol range unit condition input v oltage r ange v cc 8.9 to 25 .0 v vcc v oltage 2/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj electrical characteristics ( unless otherwise specified v cc =15 v ta = 25 c) item s ymbol specification unit condition min typ max circuit c urrent circuit current (on) i on - 400 8 00 a zt=0v (p ulse o perating) circuit current (o ff ) i off - 300 6 00 a zt = 1v (p ulse off) chg p in c harge c ircuit chg c harge c urrent 1 i start1 0.2 5 0. 35 0.45 ma vcc= 0v , chg=15v chg c harge c urrent 2 i start2 2 6 12 ma vcc=10v , chg=15v chg off c urrent i start3 3 6 9 a vcc uvlo r eleased chg p in s ink c urrent chg= 15 v chg c harge current s witching v oltage v sc 0. 4 0. 8 1.6 v vcc p in vcc p in protection v cc u vlo v oltage 1 v uvlo1 12.5 13.5 14.5 v vcc r ising up vcc uvlo v oltage 2 v uvlo2 7.5 8.2 8.9 v vcc f alling d own vcc uvlo h ysteresis v uvlo3 - 5.3 - v v uvlo3 = v uvlo1 - v uvlo2 vcc ovp t rigger v oltage v ovp1 25 .0 27.5 30 .0 v vcc r ising up vcc ovp r elease v oltage v ovp2 21 .0 23.5 26 .0 v vcc f alling d own latch r eleased vcc v oltage v latch - v uvlo2 - 0.5 - v vcc f alling d own vcc r echarge s tart v oltage v chg1 7.7 8.7 9.7 v vcc f alling d own vcc r echarge e nd v oltage v chg2 12 13 14 v vcc r ising up latch m ask t ime t latch 75 150 300 s [ dc/dc c onverter b lock ( t urn - on ) ] zt c omparator v oltage 1 v zt1 30 110 190 mv zt f alling d own zt c omparator v oltage 2 v zt2 1 00 200 30 0 mv zt r ising up zt c omparator h ysteresis v zthys 40 90 140 mv v zthys = v zt 2 - v zt 1 zt t rigge r t imeout t ztout 9 18 36 s [ dc/dc c onverter b lock ( t urn -off) ] current trigger v oltage v cs 2.60 2.95 3.30 v maximum f requency f sw 255 3 00 345 k hz leading e dge b lank t ime t leb 0.1 0.2 0.4 s error a mplifier r eference v oltage v ref 0.582 0.600 0 .618 v [ driver b lock ] out pin h igh voltage v outh 10 .5 12. 0 14.5 v ou t high on resistance r outh 23 45 76 i out = -2ma out low on resistance r outl 33 65 110 i out = +2 ma 3/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj pin con f iguration pin descript io ns table 1. pin f unction s no. pin name function 1 zt zero current detecting pin 2 vcc power supply pin 3 chg i nput pin of the charge circuit 4 out gate pin of the external mosfet 5 cs inductor current sensing pin 6 comp error amplifier out put pin 7 gnd gnd pin 8 lpf error amplifier input pin i/o e quivalen ce c ircuit s 1pin : zt 2pin : vcc / 7pin : gnd 3pin : chg zt(1) 50 100 10k 25k 200k 300k vcc(2) gnd(7) block chg(3) vcc(2) chg (3) 4pin : out 5pin : cs 6pin : comp out(4) gnd(7) internal 12v 100k cs(5) vref4v 1m 18k 25k 4k 10k 10k comp(6) 8pin : lpf lpf(8) 10k figure 3. i/o e quivalent c ircuit s (top view) lpf gnd cs zt vcc chg out comp 7 8 6 5 3 4 2 1 figure 2. pin c onfiguration 4/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj block diagram starter vcc (2) vin logic 12v clamper 200ns l.e.b. 150us mask s r q rs tsd vccuvlo vccrechg vccovp ocp nout ztcomp nout startcomp max freq. power supply vccuvlo vref4v vref4v r2 driver zt (1) gnd (7) 0.8v 13v/ 8.7v 13.5v/ 8.2v 27.5v/ 23.5v 110mv/ 200mv 1m 2.95v istart1=0.35ma istart2=6ma istart3=6ua chg (3) r1 f1 cin c1 c3 d1 l2 co led+ led- eamp 0.6v comp (6) osc c2 d2 lpf (8) ro r3 cb l1 da1 r4 rout dout q1 out (4) cs (5) dz2 q2 dz1 figure 4. blo ck d iagra m 5/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj description of block s (1) charge c ircuit b lock ( vcc: 2pin , chg : 3 pin ) (1. 1)block description a charge circuit is built in this ic. after the ic starts up , the power consumption becomes only the idling cu rr en t i start3 (typ =6 a). starter block vccuvlo vccrechg startcomp 0.8v 13v/ 8.7v 13.5v/ 8.2v istart1=0.35ma istart2=6ma istart3=6ua on on chg (3) vin r1 f1 cin vcc (2) istart1 istart2 istart3 c1 da1 cb l1 d2 r3 gnd (7) q2 dz2 figure 5 . charge c ircuit b lock d iagram figure 6. charge current vcc v oltage c urve for reducing the number of the components, the application schematic which consists by the starter resistor rst r and the protection z ener diode d z 3 is showed in figure 7. vin cs(5) gnd(7) chg(3) vcc(2) f1 da1 l1 cb cin d1 dz1 rs co u1 ro d2 r3 c1 l2 led+led- out(4) q1 rout dout rstr dz3 + figure 7. application c ircuit e xample for dcdc ( the i nternal c harge circuit is not used) i start1 i start2 v sc v uvlo1 10v vcc voltage[v] i start3 0 charge current [a] 6/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj ( 1. 2) start s equence s the time chart of the start sequences are showed in figure 8. vcc(2) comp(6) switching i_led vuvlo1 vuvlo2 (a) (b) (c) (e) (d) (f) ac power supply off on off out(4) figure 8 . on/off s equence s on/off s equence s a : input voltage is applied to chg pin when the ac power supply turns on . b: the capacitor connected to the vcc pin is charged by the star t- up current from the c hg pin, and the vcc rises up. c: t he ic starts operating when v cc > v uvlo1 (typ =13.5v) d: by the increase of the comp pin voltage, the ic starts up with the soft - start operation. e: the current is supplied to vcc pin from led+ and d2 by the switching op eration of out pin . the power is supplied from led+, and t h e vcc voltage is determined by the v dz 1 (the breakdown voltage of dz 1) . v cc =v led -v dz 1 -vf d2 (v led : the vf of led, v dz 1 : the breakdown voltage of dz 1 , vf d2 : the vf of d2 ) f : when the power supply turns off, vcc v oltage falls down d ue to the drop of the power supply . th e ic turns off when the v uvlo2 (typ =8.2v) is triggered. 7/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj ( 1. 3) vcc p in p rotection f unction s the vcc under voltage protection function vcc uvlo ( under voltage lock out), over voltage protection function vcc ovp (over voltage protection), and a vcc re charge function which operates when a voltage drop occurs at vcc pin are built in this ic. the vcc uvlo and vcc ovp function s are u sed for preventing from the destructions of the switching mosfet which occurs when the vcc voltage gets too high or too low. owing to the vcc charge function , the vcc pin is charged by the charge circuit when the vcc voltage drops . vcc uvlo / vcc ovp f unction vcc uvlo and vcc ovp are comparator s which have voltage hysteresis . (the comparator of vcc uvlo is auto recovery type, and the comparator of vcc ovp is latch type.) vcc ovp has a built - in mask time t latch (typ =1 50 s). when the vcc voltage is over v ovp 1 (typ =27.5v ), and this state lasts t latch , the detection is executed. owing to this function, the surge which occurs at vcc pin can be masked . vc c c harge f unction when the vcc pin voltage is over v uvlo1 (typ =13.5 v) , the ic starts up. in this case, if the vcc pin voltage drops below v chg1 (typ =8.7v) , vcc charge function operates . at th is time , the vcc pin is charged from the chg pin through the charge circuit . owing to this operation , the failure of start - up can be prevented . v uvlo1 (typ=13.5v) on off v ovp1 (typ=27.5v) switching v uvlo2 (typ=8.2v) vcc uvlo function on off off vcc ovp function on off a b c off internal latch signal l : normal h : latch g v latch (typ=7.7v) time v ovp2 (typ=23.5v) h g i on off d v chg2 (typ=13v) v chg1 (typ=8.7v) vcc recharge function on off on off on v sc (typ=0.8v) e f istart2 (typ=6ma) istart1 istart2 on lkj vcc (2) under t latch (typ=150us) over t latch (typ=150us) istart1 (typ=350ua) chg (3) figure 9 . timing c hart of vcc uvlo/ vcc ovp / vcc c harge f unction a : chg pin voltage is applied , vcc voltage rises by the charging current istart1 (typ =3 50 a). b: vcc voltage > v sc (typ =0.8v) , the charging current to vcc changes from i start1 to istart2 (typ =6ma) c: vcc voltage > v chg 2 (typ =13v) , though vcc charge function reacts, due to vcc uvlo is detected, the charge continues. d: vcc voltage > v uvlo 1 , the v cc uvlo is released, the dc/dc operation starts, and the vcc charge operation stops. e: vcc voltage < v chg 1 , the vcc charge operation restarts. f: vcc voltage > v chg2, the vcc charge operation stops. g: vcc voltage > v ovp 1 , vcc ovp is detected. h: vcc voltage < v ovp 2 (typ =23.5v) , if vcc voltage drops below v ovp 2 in t latch , vcc ovp is released , and the latch will not be activated. i: vcc voltage > v ovp 2 , if this state is kept longer than t latch , the switching stops by latch. j: vcc voltage< v uvlo 2 (typ =8.2v) , vcc uv lo is detected. k: vcc voltage< v latch (typ =7.7v) , the latch state is released. l: vcc voltage < v sc , the charge current to vcc changes from i start2 to istart1 8/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj (2 ) error a mplifier b lock ( cs : 5pin, comp : 6 pin, lpf : 8pin ) (2. 1)block description an error amp lifier is built in this ic, the high time of the out pin changes by controlling the output of the error amplifier. the voltage which occurs on the current sensing resistor rs (cs p in v oltage) is inputted to the rc filter circuit which is composed by r4, c 2. t he output of the low pass filter circuit (lpf p in v oltage) is used as the input voltage of the error amplifier, and the summation of the current which flows through the inductor l2 while the mosfet is on, and the current which flows through the inducto r l2 from the flywheel diode d1 while the mosfet is off flows through the rs. +- comp eamp cs(5) comp(6) out(4) ton control rs c3 lpf(8) gnd(7) c2 r4 + - ocp v ocp (typ=2.95v) stop + - vref4v 1m v ref (typ=0.6v) l2 d1 figure 10 . error a mplifier b lock d iagram ( 2. 2) cs p in ocp protection an ocp (over current protection) function is built in the cs pin. while the voltage of cs pin rises up to the trigger voltage v ocp (typ = 2.95v), the mosfet is forced to turn off. (a uto matic r ecovery p rotection ) ( 2. 3) l.e.b b lanking p eriod w hen the mosfet is turned on, surge current occurs by the capacit ive component s and driv e current. in this case , if the cs pin voltage rises temporarily , the false detection s may occur in the over current limiter circuit . for prevent ing from the false detections, a n l.e.b ( leading edge blanking ) function which masks the cs voltage during a co nstant time t leb (typ = 200ns) after the out pin switches form l ow to h igh is built in. ( 2. 4) cs pin open p rotection w hen the cs pin becomes open, this function stops the switching operation for protection. ( a uto matic r ecovery p rotection ) 9/ 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj (3)zer o current detection block ( zt : 1pin ) (3. 1)block description zt pin (1pin) controls the low time of the output of out pin. while the output is low (mosfet: off) , the current flows from the flywheel diode d1 to the inductor l2 . while the current i l is c lose to zero, the voltage of zt pin falls down. while the voltage becomes lower than v zt1 (typ =1 10 mv ) , it is detected by the zt comparator, and the output of out pin turns to high (mosfet: on). v zt1 (typ=110mv) cs (5) il zt (1) 0a out (4) il zt (1) out (4) figure 11 . zero - cross d etecti on by zt p in (3. 2) zt tigger timeout in case of the zt pin is locked at low voltage which is caused by some malfunctions of the com ponents on the application, and the q uasi - resonant s witching operation stops, the output of out pin turns to high after t z tout (typ = 18 s). i l zt (1) out (4) t out_on ztout t ztout t ( a ) ( b ) ( c ) v zt1 t out_on 0a cs (5) figure 12. zt trigger timeout operation (a) when the on time (t out_on ) which is determined by the voltage of comp pin passed, the output of out pin turns to low . (b) the zt pin is locked at a low voltage, the output of out pin keeps low . (c) when t ztout passed after the output of out pin turns to low , the output of out pin turns to high . (3.3 ) maximum frequency the maximum frequency is a function which is designed for preventing from the overheating of the ic, and it limits the ic to operat e under the f max (typ = 300khz). il cs (5) zt (1) out (4) ( a ) out_on t v zt1 ( b ) ( c ) t ztout t max = 1 / f max [s] t max 0a figure 13 . maximum f requency o peration (a) when the on time (t out_on ) which is determined by the voltage of comp pin passed, the output of out pin turns to low . (b) if t he switching frequency exceeds the f max , the output of out pin cannot turn to high . (c) when t ztout passed after the output of out pin turns to low , the output of out pin is forced to turn to high . 10 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj operation m ode of p rotection c ircuit operation mode of protection functions are shown in table 2. table 2. operation m ode of p rotection c ircuit abnormal state d etection detect ion release protection o perations vcc uvlo <= 8.2v (typ ) >= 13.5v (typ ) ic s tops (a utomatic r ecovery ) ovp >=27.5v (typ ) before l atch <= 23.5v (typ ) latched v cc <= 7.7v (typ ) 150 s (typ ) timer l atch cs ocp >= 2.95 v (typ ) <2.95v (typ ) output s tops (a utomatic r ecovery ) tsd >=1 75 o c (typ ) before l atch <= 1 55 o c (typ ) latched v cc <= 7.7v (typ ) 150 s (typ ) timer l atch 11 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj operational notes 1. r everse c onnection of p ower s upply connecting the power supply in reverse polarity can damage the ic. take pr ecautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the ic s power supply pin s. 2. power s upply l ines design the pcb layout pattern to provide low impedance supply lines. s eparate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affect ing the analog block . furthermore, connect a capacitor to ground at all power supply pins . consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors . 3. g round voltage ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. g round w iring pattern when using both small - signal and large - current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuatio ns in the small - signal ground caused by large currents. also ensure that the ground traces of external compo nents do not cause variations on the ground voltage. the ground lines must be as short and thick as possible to reduce line im pedance. 5. thermal c onsideration should by any chance the maximum junction temperature rating be exceeded the rise in tem perature of the chip may result in deterioration of the properties of the chip. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the maximum junction t emperature rating. 6. recommended o perating c onditions these conditions represent a range within which the expected characteristics of the ic can be approxima tely obtained . the electrical characteristics are guaranteed under the conditions of each parameter . 7. inrush current when power is first supplied to the ic, it is possible that the internal logic may be unst able and inrush current may flow instantaneously due to the internal powering sequence and delays, especially if t he ic has more than one power supply. therefore, give special consideration to power coupling capacitance, p ower wiring, width of ground wiring, and routing of connections. 8. operation u nder s trong e lectromagnetic f ield operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction . 9. testing on a pplication b oards when testing the ic on an application board, connecting a capacitor directly to a low - impedance o utput pin may subject the ic to stress. always discharge capacitors completely after each proce ss or step. the ics power supply should always be turned off completely before connecting or removing it from the test setup during the i nspection process. to p revent damage from static discharge, ground the ic during assembly and use similar prec autions during transport and storage. 10. inter- pin short and mounting errors ensure that the direction and position are correct when mounting the ic on the pcb. incorrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground, power supply an d output pin . inter - pin shorts could be due to many reasons such as metal particles, water droplets (in very humid enviro nment) and unintentional solder bridge deposited in between pins during assembly to name a few. 12 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj operational notes C continued 11. unused input terminals input pins of an ic are often connected to the gate of a mos transistor. the gate has extremely high i mpedance and extremely low capacitance. if left unconnected, the electric field f rom the outside can easily charge it. the small charge acquired in this way is enough to produce a significant effect on the conduction through t he transistor and cause unexpected operation of the ic. so unless otherwise specified, unused input pins should be connected to the power supply or ground line. 12. regarding the i nput p in of the ic this monolithic ic contains p+ isolation and p substrate layers between adjacent elements in order to keep them isolated. p - n junctions are formed at the intersection of the p layers with the n layers of other elements, creating a parasitic diode or transistor. for example (refer to figure below): when gnd > pin a and gnd > pin b, the p - n junction operates as a parasitic diode. when gnd > pin b, the p - n junction operates as a parasitic transistor. parasitic diodes inevitably occur in the structure of the ic. the operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. therefore , conditions that cause these diodes to operate, such as applying a voltage lower than the gnd voltage to an input pin (and thus to the p substrate) should be avoided. fig ure 14. example of monolithic ic structure 13. ceramic capacitor when using a ceramic capacitor, determine the dielectric constant consider ing the change of capacitance with temperature and the decrease in nominal capacitance due to dc bias and others. 14. area of safe operation (aso) operate the ic such that the output voltage, output current, and the maximum junction temp erature rating are all within the area of safe operation (aso) . 15. thermal s hutdown circuit(tsd) this ic has a built - in thermal shutdown circuit that prevents heat damage to the ic. normal operation should always be within the ics maximum junction temperature rating. if however the rating is exceeded for a c ontinued period, the junction temperature (tj) will rise which will activate the tsd circuit that will t urn off all output pins. the ic should be powered down and turned on again to resume normal operation because the tsd circ uit keeps the outputs at the off state even if the tj falls below the tsd threshold. note that the tsd circuit operates in a situation that exceeds the absolute maximum rat ings and therefore, under no circumstances, should the tsd circuit be used in a set design or for any purpose other than protect ing the ic from heat damage. 16. over c urrent p rotection c ircuit (ocp) this ic incorporates an integrated overcurrent protection circuit that is activat ed when the load is shorted. this protection circuit is effective in preventing damage due to sudden and unexpected incidents. how ever, the ic should not be used in applications characterized by continuous operation or transitioning of the prot ection circuit. 13 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj ordering information b d 5 2 1 g o f j - xx product name package fj: sop - j8 packaging and forming specification xx: please confirm the formal name with our salesmen. marking diagram sop - j8(top view) 521go part number marking lot number 1pin mark 14 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj physical dimension , tape and reel information package name sop -j8 15 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
b d521gofj revision history date revision changes 18. jan .201 6 001 new release 20.apr.2016 002 p2 footprints and traces changed the representation of the units. 74.2mm 2 (square) ? 74 .2 mm x 74.2 mm 16 / 16 tsz02201 - 0f4f0c300 10 0-1-2 20 . apr .201 6 rev.00 2 ? 20 16 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 downloaded from: http:///
notice-p ga -e rev.003 ? 201 5 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufactured for application in ordinary electronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). if you intend to use our products in devices requiring extremely h igh reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecraft, nuclear powe r controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ( specific applications ), please consult with the rohm sales representative in adv ance. unless otherwise agreed in writing by rohm in advance, rohm s hall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arisin g from the use of any rohm s products for specific applications. (note1) medical equipment classification of the specific appl ications japan usa eu china class class class b class class ? class 2. rohm designs and manufactures its products subject to stri ct quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequ ate safety measures including but not limited to fail-safe desig n against the physical injury, damage to any property, whic h a failure or malfunction of our products may cause. the followi ng are examples of safety measures: [a] installation of protection circuits or other protective devic es to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified be low. accordingly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from th e use of any rohms products under any special or extraordinary environments or conditions. if yo u intend to use our products under any special or extraordinary environments or conditions (as exemplified belo w), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be n ecessary: [a] use of our products in any types of liquid, including water, oils, chemicals, and organi c solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products are e xposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed t o static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing component s, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subject to radiation-proof design. 5. please verify and confirm characteristics of the final or mou nted products in using the products. 6 . in particular, if a transient load (a large amount of load appl ied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mou nting is strongly recommended. avoid applying power exceeding normal rated power; exceeding the power rating u nder steady-state loading condition may negatively affec t product performance and reliability. 7 . de -rate power dissipation depending on ambient temperature. wh en used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8 . confirm that operation temperature is within the specified range desc ribed in the product specification. 9 . rohm shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlorine, bromine, etc .) flux is used, the residue of flux may negatively affect prod uct performance and reliability. 2. in principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method mus t be used on a through hole mount products. i f the flow soldering method is preferred on a surface-mount p roducts , please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
notice-p ga -e rev.003 ? 201 5 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, p lease allow a sufficient margin considering variations o f the characteristics of the products and external components, inc luding transient characteristics, as well as static characteristics. 2. you agree that application notes, reference designs, and a ssociated data and information contained in this docum ent are presented only as guidance for products use. therefore, i n case you use such information, you are solely responsible for it and you must exercise your own independ ent verification and judgment in the use of such information contained in this document. rohm shall not be in any way respon sible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such informat ion. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take pr oper caution in your manufacturing process and storage so t hat voltage exceeding the products maximum rating will not be applied to products. please take special care under dry co ndition (e.g. grounding of human body / equipment / solder iro n, isolation from charged objects, setting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriorate i f the products are stored in the places where: [a] the products are exposed to sea winds or corrosive gases, in cluding cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to direct sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage condition, solderabil ity of products out of recommended storage time period may be degraded. it is strongly recommended to confirm so lderability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the correct direction, which is indi cated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a c arton. 4. use products within the specified time after opening a humi dity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage tim e period. precaution for product label a two-dimensional barcode printed on rohm products label is f or rohm s internal use only. precaution for disposition when disposing products please dispose them properly usi ng an authorized industry waste company. precaution for foreign exchange and foreign trade act since concerned goods might be fallen under listed items of export control prescribed by foreign exchange and foreign trade act, please consult with rohm in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to appl ication example contained in this document is for reference only. rohm does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. rohm shall not have any obligations where the claims, a ctions or demands arising from the combination of the products with other articles such as components, circuits, systems or ex ternal equipment (including software). 3. no license, expressly or implied, is granted hereby under any inte llectual property rights or other rights of rohm or any third parties with respect to the products or the information contai ned in this document. provided, however, that rohm will not assert it s intellectual property rights or other rights against you or you r customers to the extent necessary to manufacture or sell products containing the products, subject to th e terms and conditions herein. other precaution 1. this document may not be reprinted or reproduced, in whole or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any way whatsoever the pr oducts and the related technical information contained in the products or this document for any military purposes, includi ng but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice ? we rev.001 ? 2015 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///

▲Up To Search▲

Price & Availability of BD521GOFJ-E2

	To Download BD521GOFJ-E2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .