357 beloit street, p.o. box 457, burlington, wi 53105-0457 u.s.a. phone 262/763-3591 fax 262/763-2881 email: nelsales@nelfc.com www.nelfc.com differential positive ecl (dpecl) hs-2870 series description the hs-2870 series of quartz crystal oscillato rs provide mecl 10k and 10kh series compatible signals in industry standard four-pin dip hermetic packages. syst ems designers may now specify space-saving, cost- effective packaged pecl oscillators to meet their timing requirements. this device is intended to operate on positive voltage for pecl applications. features ? wide frequency range?15.0mhz to 250.0mhz ? user specified tolerance available ? will withstand vapor phase temperatures of 253c for 4 minutes maximum ? space-saving alternative to discrete component oscillators ? high shock resistance, to 3000g ? all metal, resistance weld, hermetically sealed package ? low jitter ? mecl 10k and 10kh series compatible output on pin 8, complement on pin 1 ? high q crystal actively tuned oscillator circuit ? power supply decoupling internal ? no internal pll avoids cascading pll problems ? high frequencies due to proprietary design ? gold plated leads - solder dipped leads available upon request ? rohs compliant, lead free construction (unless solder dipped leads are supplied) ? cots/dual use electrical connection pin connection 1 output complement 7 v ee /ground 8 output 14 v cc +5.0v dimensions are in inches and (mm) crystal clock oscillators data sheet 9205d rev. u
357 beloit street, p.o. box 457, burlington, wi 53105-0457 u.s.a. phone 262/763-3591 fax 262/763-2881 email: nelsales@nelfc.com www.nelfc.com hs-2870 series continued differential positive ecl (dpecl) operating conditions and output characteristics electrical characteristics parameter symbol conditions min typical max frequency ----- ----- 15.0mhz ----- 250.0mhz duty cycle ----- @v cc -1.29v 45/55% ----- 55/45% logic 0 (2) v ol ----- v cc -1.95v ----- v cc -1.60v logic 1 (2) v oh ----- v cc -1.02v ----- v cc -0.74v rise & fall time tr,tf 20-80%v o with 50 ohm load to v cc -2v ----- 1.0 ns 1.5 ns tpd (4) ----- ----- -0.5 ns ----- +0.5 ns jitter, rms (3) ----- ----- ----- ----- 5 psec frequency stability (1) df/f overall conditions including: -100ppm ----- +100ppm voltage, calibration, temp., 10 yr aging, shock, vibration general characteristics parameter symbol conditions min typical max supply voltage v cc ----- 4.75v 5.0v 5.25v supply current i cc 50 ohm termination 0.0 ma ----- 80 ma to 2.00v below v cc output current i o low level output current 0.0 ma ----- 50.0 ma operating temperature t a ------ 0c ----- 70c storage temperature t s ----- -55c ----- 125c power dissipation p d ----- ----- ----- 420 mw lead temperature t l soldering, 10 sec. ----- ----- 300c load 50 ohm to v cc -2v or thevenin equivalent, bias required start-up time t s ----- ----- 2 ms 10 ms environmental and mechanical characteristics mechanical shock per mil-st d-202, method 213, condition e thermal shock per mil-std- 883, method 1011, condition a vibration 0.060" double amplitude 10 hz to 55 hz, 35g?s 55hz to 2000 hz soldering condition 300c for 10 seconds hermetic seal leak rate less than 1 x 10 -8 atm.cc/sec of helium esd sensitivity human body model per on semiconductor 10kh series ecl: 500v min. footnotes: 1) standard frequency stability (20, 25,50ppm & others available) 2) v ol , v oh , referenced to ground (v ee ) with v cc = 5v 3) jitter performance is frequency dependent. please contact factory for full characterization. rms jitter bandwidth of 12khz to 20mhz. 4) tpd is phase shift between the falling edge of pin 8 at v cc -1.29v and rising edge of pin 1 at v cc -1.29v. rev. u crystal clock oscillators hs - a 287x - freq package code tolerance/performance hs leaded 4 pin (14 pin) 0 100ppm 0-70c sm leaded 4 pin (14 pin ) smd 1 50ppm 0-70c gull wing 7 25ppm 0-70c input voltage 9 customer specific code specification a 20ppm 0-70c a 3.3v b 50ppm -40 to +85c 5v c 100ppm -40 to +85c creating a part number data sheet 9205d
|