Part Number Hot Search : 
X00619 1N1197 5K16TR 7M035 GB19264 705G1 35024 25N60
Product Description
Full Text Search
 

To Download 78P2351-DB-ECLM Datasheet File
  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
　
 

  Datasheet File OCR Text:
  78p2351 single channel oc-3/ stm1-e/ e4 liu data sheet page: 1 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 september 2006 description the 78p2351 is teridians second generation line interface unit (liu) for 155 mbps (oc-3, sts-3, or stm-1) and 140 mbps pdh (e4) telecom interfaces. the device is a single chip solution that includes an integrated cdr in the transm it path for flexible nrz to cmi conversion. the device can interface to 75 ? coaxial cable using cmi coding or directly to a fiber optics transceiver module using nrz coding. the 78p2351 is compliant with all respec tive ansi, itu-t, and telcordia standards for jitter tolerance, generation, and transfer. applications ? central office interconnects ? dslams ? add drop multiplexers (adms) ? pdh/sdh test equipment ? multi service switches ? digital microwave radios features ? itu-t g.703 compliant cable driver for 139.264 mbps or 155.52 mbps cmi-coded coax transmission ? integrated adaptive cmi equalizer and cdr in receive path handles over 12.7db of cable loss ? serial, lvpecl-compatible system interface with integrated cru in tr ansmit path for flexible nrz to cmi conversion. ? 4-bit parallel cmos system interface with master and slave tx clock modes. ? selectable lvpecl com patible nrz media interface for 155.52 mbps optical transmission. ? configurable via hw control pins or 4-wire serial interface ? compliant with ansi t1.105.03-1994; itu-t g.751, g.813, g.823, g.825, g.958; and telcordia gr-253-core for jitter performance. ? receiver loss of signal (los) detection compatible with itu-t g.783 ? operates from a single 3.3v supply ? 100-pin jedec lqfp block diagram rxp/n sodp/n sockp/n po[3:0]d pock ptock pi[3:0]d pick sickp/n sidp/n eclp/n txckp/n cmip/n cmi2p/n rx cdr cmi decoder fifo tx cdr lock detect cmi encoder lock detect adaptive eq. los detect pmod, smod[1:0], par llbk rlbk, rdsl cmi downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 2 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 table of co ntents ................................................................................................. 2 functional de scription........................................................................................ 4 mode selection................................................................................................................. ...............4 reference clock ................................................................................................................ ............4 receiver o peration ............................................................................................................. ..........4 receiver m onitor mode .......................................................................................................... ........4 receive loss of signal ......................................................................................................... .........5 receive loss of lock........................................................................................................... ..........5 transmitter operation .......................................................................................................... ......5 synchronous (re -timing) tx seri al modes ..................................................................................5 plesiochronous tx serial modes ................................................................................................. .6 synchronous pa rallel modes ..................................................................................................... ...6 transmit fifo description ...................................................................................................... ......6 transmit driver ................................................................................................................ ...............7 transmit m onitor mode.......................................................................................................... ........7 clock synt hesizer.............................................................................................................. .............7 transmit backpla ne equalizer ................................................................................................... ...7 transmit lo ss of lock .......................................................................................................... .........7 power-down function ........................................................................................................... ......7 loopback modes ................................................................................................................. ............8 power-on reset ................................................................................................................ ..............8 serial control interf ace ...................................................................................................... ...9 programmable interrupts ........................................................................................................ 9 register desc ription........................................................................................... 10 register addressing............................................................................................................ .......10 register table................................................................................................................. ..............10 legend ......................................................................................................................... ......................11 global registers .........................................................................................................................11 address 0-0: master control re gister .......................................................................11 address 0-1: interrupt control register..................................................................12 address 0-2: i/o co ntrol regi ster .................................................................................12 port-specific registers ............................................................................................................13 address 1-0: mode control re gister ...........................................................................13 address 1-1: signal control re gister.........................................................................14 address 1-2: advanced tx control regi ster 1 .........................................................15 address 1-3: advanced tx control regi ster 0 .........................................................15 address 1-4: mode co ntrol regist er 2 ........................................................................15 address 1-5: status monitor re gister.........................................................................16 downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 3 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 table of contents (continued) pin descri ption ....................................................................................................... 17 legend ......................................................................................................................... ......................17 transmitte r pi ns ............................................................................................................... ............17 receiver pins .................................................................................................................. ................18 reference and st atus pins ...................................................................................................... 19 control pins .................................................................................................................. ................20 serial-port pins ............................................................................................................... .............22 power and gr ound pins .......................................................................................................... ...22 electrical speci fications ................................................................................. 23 absolute maximu m ratings....................................................................................................... ...23 recommended operat ing condit ions ......................................................................................23 dc character istics............................................................................................................. ............23 analog pins c haracteristics .................................................................................................... .24 digital i/o char acteristics.................................................................................................... ......24 pins of type ci, ciu, cid ................................................................................................................24 pins of type cit ..............................................................................................................................2 4 pins of type cis ..............................................................................................................................2 4 pins of type co and coz ...............................................................................................................25 pins of type po ............................................................................................................................... 25 pins of type pi ............................................................................................................................... ..25 pins of type od ............................................................................................................................... 25 serial-port timing characteris tics........................................................................................26 transmitter timing characteri stics ......................................................................................27 timing diagram: tran smitter wave forms .......................................................................................27 reference clock ch aracteris tics..........................................................................................28 receiver timing characteristics..............................................................................................28 timing diagram: receive wa veforms ............................................................................................ 28 transmitter specifications for cmi in terface .................................................................29 transmitter ou tput ji tter ...................................................................................................... ....34 receiver specifications for cmi in terface (transform er-coupled) ..................................35 receiver jitte r toler ance ...................................................................................................... ....36 receiver jitter tran sfer func tion .........................................................................................38 cmi mode loss of si gnal condi tion ..........................................................................................39 application in formation .................................................................................... 39 external co mponents ............................................................................................................ .......39 (cmi) transformer specificat ions ............................................................................................39 thermal info rmation ............................................................................................................ .........39 mechanical specif ications ............................................................................... 40 package info rmation .......................................................................................... 41 ordering information ............................................................................................................ 41 revision history ............................................................................................................................... .........42 downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 4 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 functional description the 78p2351 contains all the necessary transmit and receive circuitry for connection between 139.264mbps and 155.52mbps line interfaces and the digital universe. the chip is controllable through pins or serial port register settings. in hardware mode (pin control) the spsl pin must be low. in software mode (spsl pin high), control pins are disabled and the 78p2351 must be configured via the 4-wire serial port. mode selection the sdo_e4 pin or e4 register bit determines which rate the device operates in according to the table below. this control combined with cksl also selects the reference clock frequency. rate sdo_e4 pin e4 bit e4 high 1 stm-1, sts-3, oc-3 low 0 the sen_cmi pin or cmi register bit enables the cmi encoder/decoder and selects one of two media for reception and transmission: 75 ? coaxial cable in cmi coding or optical fiber in fiber (nrz) mode. media (coding) sen_cmi pin cmi bit 75 ? coax (cmi) high 1 fiber (nrz) low 0 the sdi_par pin or par register bit selects the interface to the framer to be 4-bit parallel cmos or serial lvpecl. for each interface there are different transmit timing modes available. see transmitter operation section for more info. reference clock the 78p2351 requires a reference clock supplied to the ckrefp/n pins. this reference clock is used for clock recovery in the rx dll and tx dll. it is also used for transmit re-timing in the synchronous transmit modes. refer to the transmitter operation section for timing requirements during synchronous (re-timing) transmit modes. for reference frequencies of 77.76mhz or lower, the device accepts a single ended cmos clock at ckrefp (with ckrefn grounded). for reference frequencies of 139.264 or 155.52mhz, the device accepts a differential lvpecl clock input at ckrefp/n. the frequency of this reference input is controlled by the rate selection and the cksl control pin or register bit. reference frequency cksl pin sdo_e4 low sdo_e4 high low 19.44mhz 17.408mhz float 77.76mhz n/a high 155.52mhz 139.264mhz cksl[1:0] bits e4 bit = 0 e4 bit = 1 0 0 19.44mhz 17.408mhz 1 0 77.76mhz n/a 1 1 155.52mhz 139.264mhz receiver operation the receiver accepts seri al data, at 155.52mbps or 139.264mbps from the rxp/n inputs. in cmi mode, the input is differentially terminated with 75 ? and transformer-coupled to a coaxial connector. in fiber (nrz) mode, the input is differentially terminated with 100 ? and ac-coupled to an optical transceiver module. for board designs utilizing both coax and fiber media options, an analog switch or mechanical relay is required to switch between the different terminations and media paths. the recovered cmi signal first enters an agc and anadaptive equalizer designed to overcome inter- symbol interference caused by long cable lengths. the variable gain differential amplifier automatically controls the gain to maintain a constant voltage level output regardless of the input voltage level. note that in fiber (nrz) mode, the input signals bypass the adaptive equalizer. the outputs of the data comparators are connected to the clock recovery circuits. the clock recovery system employs a delay locked loop (dll), which uses a reference frequency derived from the clock applied to the ckrefp/n pins. in serial mode, the clock and data are decoded and transmitted through the lvpecl drivers. in parallel mode, the data is decoded and converted into four bit parallel segments before being transmitted through the cmos drivers. note that in fiber (nrz) mode, the cmi decoder is bypassed. receiver monitor mode in cmi mode, the sck_mon pin or mon register bit enables the receivers monitor mode which adds approximately 20db of flat gain to the receive signal before equalization. rx monitor mode can handle 20db of flat loss typical of monitoring points with up to 6db of cable loss. note that loss of signal detection is disabled during rx monitor mode. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 5 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 receive loss of signal the 78p2351 includes a loss of signal (los) detector. when the peak value of the received signal is less than approximately 19db below nominal for approximately 110 ui, receive loss of signal is asserted. the rx los signal is cleared when the received signal is greater than approximately 18db below nominal for 110 ui. in ecl mode, the los signal will be asserted when there are no transitions for longer than 2.3 s. the signal is cleared when there are more than 4 transitions in 32 ui. it is generally recommended to use the los status signal from the optical transceiver module. during rx los conditions, the receive clock will remain on the last phase tap of the rx dll outputting a stable clock while the receive data outputs are squelched and held at logic 0. note : rx loss of signal detection is disabled during local loopback and receive monitor modes. receive loss of lock the 78p2351 includes an optional receiver loss of lock detector that will flag if the recovered rx clock frequency differs from the reference clock by more than 100ppm in an interval greater than 420 s. this condition is cleared when the frequencies are less than 100ppm off for more than 500 s. notes : 1. during rx loss of signal (rlos), the rx loss of lock indicator is undefined and may report either status. 2. for reliable operation, the lolor bit in the signal control register should be toggled upon power-up and configuration. transmitter operation at the media interface, the transmit driver generates an analog signal for transmission through either a transformer and 75 ? coaxial cable or directly to a fiber optics transceiver for electrical to optical conversion. at the host interface, the 78p2351 provides a number interface options for compatibility with most off-the-shelf framers and custom asics. a selectable 4-bit parallel or nibble interface is available with both slave or master timing options as well a serial lvpecl interf ace with various timing recovery modes. each of the serial nrz transmit timing modes can be configured in hw mode or sw mode as shown in the table below. hw control pins sw control bits serial mode sdi_par ckmode par smod[1:0] synchronous clock + data low low 0 0 0 synchronous data only low floating 0 1 0 plesiochronous data only low high 0 0 1 loop-timing n/a n/a x 11 synchronous (re-timing) tx serial modes in figure 1, serial nrz transmit data is input to the sidp/n pins at lvpecl levels. by default, the data is latched in on the rising edge of sickp. an integrated fifo decouples the on chip and off chip clocks and re-clocks the data using a clean synthesized clock generat ed from the provided reference clock. as such, the sickp/n clock provided by the framer/mapper ic must be source synchronous with the provided reference clock when the fifo is to be used. tdk 78p2351 framer/ mapper nrz nrz 140 / 155 mhz system reference clock sodp/n sockp/n sidp/n ckrefp/n rxp/n cmip/n xfmr xfmr coax coax 140 / 155 mhz sickp/n cmi cmi figure 1: synchronous clock and data available (tx cdr bypassed, fifo enabled) if an off-chip serial transmit clock is not available, as in figure 2, the 78p2351 can recover a tx clock from the serial nrz data input and pass the data through the clock decoupling fifo. the data is then re-clocked or re-timed using a clean synthesized clock generated from the provided reference clock. in this mode, the nrz transmit data must be source synchronous with the reference clock applied at ckrefp/n. tdk 78p2351 framer/ mapper nrz nrz 140 / 155 mhz system reference clock sodp/n sockp/n sidp/n ckrefp/n rxp/n cmip/n xfmr xfmr cmi cmi coax coax figure 2: synchronous data only (tx cdr enabled, fifo enabled) downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 6 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 plesiochronous tx serial mode figure 3 represents a common condition where a serial transmit clock is not available and/or the data is not source synchronous to the reference clock provided to the 78p2351. in this mode, the 78p2351 will recover a transmit clock from the serial plesiochronous data and bypass the internal fifo and re-timing block. this mode is commonly used for mezzanine cards, modules, and any application where the reference clock cant always be synchronous to the transmit source clock/data. tdk 78p2351 framer/ mapper nrz nrz 140 / 155 mhz reference clock sodp/n sockp/n sidp/n ckrefp rxp/n cmip/n xfmr xfmr cmi cmi coax coax xo figure 3: plesiochronous data only (tx cdr enabled, fifo bypassed) synchronous parallel modes in parallel modes, 4-bit cmos data segments are input to the chip with a 34.816mhz (e4 4) or 38.88mhz (stm1 4) synchronous clock. these inputs are re-timed in a 4x8 clock decoupling fifo and then to a serializer for transmission. because the data is passed through the fifo and re-timed using a synthesized clock, the transmit nibble clock and data must be source synchronous to the provided reference clock. for maximum compatibility with legacy asics, the 78p2351 can operate in both slave and master clock modes as shown in figures 4 and 5 respectively. note : a loop-timing mode is also available to allow external remote loopbacks (i.e. line loopback in framer). in this mode, the fifo is still enabled, but the tran smit data will be re- timed using the recovered receive clock. hw control pins sw control bits parallel mode sdi_par ckmode par pmode slave high low 1 0 slave + *loop-timing high float 1 0 master high high 1 1 *to enable loop-timing in software mode, set smod[1:0]=11 4-bit cmos ttl 4-bit cmos ttl tdk 78p2351 framer/ mapper reference clock ckrefp/n rxp/n cmip/n xfmr xfmr cmi cmi coax coax po[3:0]d pock pixck pi[3:0]d 34/39 mhz 34/39 mhz figure 4: slave parallel mode 4-bit cmos ttl 4-bit cmos ttl tdk 78p2351 framer/ mapper reference clock ckrefp/n rxp/n cmip/n xfmr xfmr cmi cmi coax coax po[3:0]d pock ptock pi[3:0]d 34/39 mhz 34/39 mhz figure 5: master parallel mode transmit fifo description since the reference clock and transmit clock/data go through different delay paths, it is inevitable that the phase relationship between the two clocks can vary in a bounded manner due to the fact that the absolute delays in the two paths can vary over time. the transmit fifo allows long-term clock phase drift between the tx clock and system reference clock, not exceeding +/- 25.6ns, to be handled without transmit error. if the cl ock wander exceeds the specified limits, the fifo w ill over or under flow, and the ferr register signal will be asserted. this signal can be used to trigger an interrupt. this interrupt event is automatic ally cleared when a fifo reset (frst) pulse is applied, and the fifo is re- centered. notes : 1) external remote loo pbacks (i.e. loopback within framer) are not possible in synchronous operation (fifo enabled) unless the data is re-justified to be synchronous to the system reference clock or the 78p2351 is configured for loop-timing operation. 2) during ic power-up or transmit power-up, the clocks going to the fifo may not be stable and cause the fifo to overflow or underflow. as such, the fifo should be manually reset using frst anytime the transmitter is powered-up. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 7 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 transmit driver in cmi (electrical) mode, the cmip/n pins are biased and terminated off-chip. they interface to 75 ? coaxial cable through a 1:1 wideband transformer and coaxial rf connectors. reference application notes for schematic and layout guidelines. the transmitter encodes the data using cmi line coding and shapes an analog signal to meet the appropriate itu-t g.703 template. the cmi outputs are tri-stated during transmit disable and transmit power-down for redundancy applications. note : to avoid reflections causing unwanted board noise, its recommended to power-down unused transmit ports that are not terminated with cable to an rx input port. when the cmi pin is low, the chip is in fiber (nrz pass-through) mode and interfaces directly to an optical transceiver module. the eclp/n pins are internally biased and output nrz data at lvpecl levels. the cmi driver, encoder and decoder are disabled in fiber (nrz) mode. transmit monitor mode an optional redundant transmit output is available in cmi mode for transmit monitoring. these outputs (cmi2p/n) are enabled when the rcsl pin or rcsl register bit is activated. tdk 78p2351 rxp/n cmip/n xfmr xfmr cmi cmi coax coax cmi2p/n xfmr cmi coax figure 6: transmit monitor output clock synthesizer the transmit clock synthesizer is a low-jitter dll that generates a 278.528/311.04 mhz clock for the cmi encoder. it is also used in both the receive and transmit sides for clock and data recovery. note : this 2x line rate clock is also available at the txckxp/n pins for downstream synchronization or system debug. transmit backplane equalizer an optional fixed lvpecl equalizer is integrated in the transmit path for architectures that use lius on active interface cards. the fixed equalizer can compensate for up to 1.5m of trace and can be enabled by the txout1 pin or txeq bit as follows: txout1 pin txeq bit tx equalizer low 1 enabled float 0 disabled transmit loss of lock in transmit modes using the integrated cdr, the 78p2351 will declare a loss of lock condition when there is no valid signal detected at the sidp/n data inputs. note : the tx lol indicator is invalid and undefined when the parallel (nibble) interface is selected. power-down function power-down control is provided to allow the 78p2351 to be shut off. transmit and receive power-down can be set independently through sw control. global power-down is achieved by powering down both the transmitter and receiver. note : the serial interface and configuration registers are not affe cted by power-down. in hw mode, the transmitters can be powered down using the txpd control pin. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 8 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 loopback modes in sw mode, llbk and rlbk bits in the signal control register are provided to activate the local and remote analog loopback modes respectively. in hw mode, the lpbk pin can be used to activate local and remote analog loopback paths as shown in the table below. lpbk pin loopback mode low normal operation float remote (analog) loopback : recovered receive clock and data looped back directly to the transmit driver. the cmi decoder and most of transmit path is bypassed (including the redundant tx monitor output) high local (analog) loopback : transmit clock and data looped back to receiver at the analog media interface. rxp/n sodp/n sockp/n po[3:0]d pock ptock pi[3:0]d pick sickp/n sidp/n eclp/n txckp/n cmip/n cmi2p/n rx cdr cmi decoder fifo tx cdr lock detect cmi encoder lock detect adaptive eq. los detect pmod, smod[1:0], par llbk rlbk, rdsl cmi figure 7: local (analog) loopback rxp/n sodp/n sockp/n po[3:0]d pock ptock pi[3:0]d pick sickp/n sidp/n eclp/n txckp/n cmip/n cmi2p/n rx cdr cmi decoder fifo tx cdr lock detect cmi encoder lock detect adaptive eq. los detect pmod, smod[1:0], par llbk rlbk, rdsl cmi figure 8: remote (analog) loopback in sw mode only, a full remote (digital) loopback bit flbk is also available in the advanced tx control register. this lo opback exercises the entire rx and tx paths of the 78p2351 including the tx clock recovery unit. as such, the user must enable either serial plesiochronous or serial loop-timing transmit modes to utilize the full remote (digital) loopback. rx cdr cmi decoder rxxp/n soxdp/n soxckp/n pox[3:0]d poxck ptoxck pix[3:0]d pixck sixckp/n sixdp/n fifo tx cdr lock detect each channel: rx cmi encoder eclxp/n cmixp/n txxckp/n lock detect each channel: tx adaptive eq. los detect pmod, smod[1:0], par llbk rlbk cmi figure 9: remote (digital) loopback internal power-on reset power-on reset (por) function is provided on chip. roughly 50 s after vcc reaches 2.4v at power up, a reset pulse is internally generated. this resets all registers to their default values as well as all state machines within the tran sceiver to known initial values. the reset signal is also brought out to the porb pin. the porb pin is a special function analog pin that allows for the following: ? override the internal por signal by driving in an external active low reset signal; ? use the internally generated por signal to trigger other resets; ? add external capacitor to slow down the release of power-on reset (approximately 8 s per nf added). note : do not pull-up the porb pin to vcc or drive this pin high during power-up. this will prevent the internal reset generator from resetting the entire chip and may result in errors. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 9 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 serial control interface the serial port controlled register allows a generic controller to interface with the 78p2351. it is used for mode settings, diagnostics and test, retrieval of status and performance information, and for on-chip fuse trimming during prod uction test. the spsl pin must be high in order to use the serial port. the serial interface consists of four pins: serial port enable (sen_cmi), serial clock (sck_mon), serial data in (sdi_par), and serial data out (sdo_e4). the sen_cmi pin initiates the read and write operations. it can also be used to select a particular device allowing sck_mon, sdi_par and sdo_e4 to be bussed together. sck_mon is the clock input that times the data on sdi_par and sdo_e4. data on sdi_par is latched in on the rising-edge of sck_mon, and data on sdo_e4 is clocked out using the falling edge of sck_mon. sdi_par is used to insert mode, address, and register data into the chip. address and data information are input leas t significant bit (lsb) first. the mode and address bit assignment and register table are shown in the following section. sdo_e4 is a tri-state capable output. it is used to output register data du ring a read operation. sdo_e4 output is normally high impedance, and is enabled only during the duration when register data is being clocked out. read data is clocked out least significant bit (lsb) first. if sdi_par coming out of the micro-controller chip is also tri-state capable, sdi_par and sdo_e4 can be connected together to simplify connections. programmable interrupts in addition to the receiver los and lol status pins, the 78p2351 provides a programmable interrupt for the transmitter. in hw control mode, the default functions of the tx interrupt is a transmit loss of lock (txlol) or fifo error (ferr). downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 10 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description register addressing address bits bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 port address sub-address read/ write assignment pa[3] pa[2] pa[1] pa[0] sa[2] sa[1] sa[0] r/w* register table a) pa[3:0] = 0 : global registers sub addr reg. name description bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 0 mscr (r/w) master control e4 <0> -- <0> par <0> cksl[1] cksl[0] -- -- srst <0> 1 intc (r/w) interrupt control inpol <0> -- <0> -- <1> -- <0> -- <0> -- mtlol <1> mferr <1> 2 iocr (r/w) i/o control -- -- -- -- -- -- -- rcsl <0> b) pa[3:0] = 1 : port-specific registers sub addr reg. name description bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 0 mdcr (r/w) mode control pdtx <0> pdrx <0> pmode smod[1] smod[0] mon <0> -- <0> -- <1> 1 sgcr (r/w) signal control tcmiinv <0> rcmiinv <0> lolor <0> rlbk <0> llbk <0> rclkp <0> tclkp <0> frst <0> 2 acr1 (r/w) advanced tx control 1 -- <0> -- <0> -- <0> -- <0> -- <0> -- <0> tpk <0> txeq <0> 3 acr0 (r/w) advanced tx control 0 -- <1> -- <0> -- <1> -- <0> -- <1> bst[1] <0> bst[0] <0> flbk <0> 4 mcr2 (r/w) mode control 2 cmi <1> -- -- -- <0> -- <0> -- <0> -- <0> -- <0> 5 stat (r/c) status monitor -- -- -- rxlos rxlol -- txlol ferr 6-7 -- reserved -- -- -- -- -- -- -- -- downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 11 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) legend type description type description r/o read only r/w read or write r/c read and clear global registers address 0-0: master control register bit name type dflt value description 7 e4 r/w 0 line rate selection : selects the line rate as well as the input clock frequency at the ckrefp/n pins. 0: oc-3, sts-3, stm-1 (155.52mhz) 1: e4 (139.264mhz) 6 -- r/w 0 unused 5 par r/w 0 serial/parallel interface selection : selects the interface to the framer. 0: serial lvpecl 1: 4-bit parallel cmos 4:3 cksl [1:0] r/w xx reference clock frequency selection : selects the reference clock frequency input at ckrefp/n pins. 11: 155.52mhz / 139.264mhz (differential lvpecl) 10: 77.76mhz / na (single-ended cmos) 00: 19.44mhz / 17.408mhz (single-ended lvpecl) secondary values correspond to e4 frequencies. default values depend on the cksl pin selection upon reset or power up. 2:1 -- r/w x0 reserved. 0 srst r/w 0 register soft-reset : when this bit is set, all registers are reset to their default values. this register bit is self-clearing. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 12 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) address 0-1: interrupt control register this register selects the event s that would cause the interrupt pins to be ac tivated. user may set as many bits as required. bit name type dflt value description 7 inpol r/w 0 interrupt pin polarity selection : 0 : interrupt output is active-low (default) 1 : interrupt output is active-high 6:2 -- r/w 01000 reserved for future use 1 mtlol r/w 1 txlol error mask (active low): gates the txlol register bit to the inttxb interrupt pin. 0: mask 1: pass 0 mferr r/w 1 fierr error mask (active low): gates the respective fierr register bit to the inttxb interrupt pin. 0: mask 1: pass address 0-2: i/o control register bit name type dflt value description 7:1 -- r/w xxxxxxx unused 0 rcsl r/w 0 redundant channel enable : enables transmit monitor outputs at cmi2p/n pins. 0: disable 1: enable downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 13 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) port-specific registers for pa[3:0] = 1 only. accessing a r egister with port address greater than 1 constitutes an invalid command. address 1-0: mode control register bit name type dflt value description 7 pdtx r/w 0 transmitter power-down : 0 : normal operation 1 : power-down. cmi transm it output is tri-stated. 6 pdrx r/w 0 receiver power-down : 0 : normal operation 1 : power-down 5 pmode r/w x parallel mode interface selection : when par=0 , pmode is invalid and defaults to logic 1; when par=1 , (master control register: bit 5), pmode selects the source of the transmit parallel clock, either taken from the framer externally or generated internally. default value is determined by ckmode pin setting upon power up or reset. 0: slave timing. pick clock input to the transmitter 1: master timing. ptock clock output from the transmitter 4 smod[1] r/w x 3 smod[0] r/w x serial mode interface selection : when par=0 (master control register: bit 5), smod[1:0] configures the transmitters system interface. default values determined by ckmode pin setting upon power up or reset. smod[1] smod[0] 0 0 synchronous clock and data are passed through a fifo. the cdr is bypassed. 1 0 synchronous data is passed through the cdr and then through the fifo. 0 1 plesiochronous data is passed through the cdr to recover a clock. fifo is bypassed because the data is not synchronous with the reference clock. 1 1 loop timing mode enable : the recovered receive clock is used as the reference for the transmit dll and fifo. when par=1 (master control register: bi t 5), setting smod[1:0] = 11 will enable loop timing mode. default values are determined by ckmode pin setting upon power up or reset as follows: ckmode low smod[1:0] default = 00 (no effect) ckmode float smod[1:0] default = 11 (loop-timing enable) ckmode high smod[1:0] default = 01 (no effect) 2 mon r/w 0 receive monitor mode enable : 0: normal operation 1: adds 20db of flat gain to t he receive signal before equalization. note : monitor mode is only available in cmi mode. 1:0 -- r/w 00 reserved downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 14 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) address 1-1: signal control register bit name type dflt value description 7 tcmiinv r/w 0 transmit cmi inversion : this bit will flip the polarity of the transmit cmi data outputs at cmip/n. for debug use only. 0: normal 1: invert 6 rcmiinv r/w 0 receive cmi inversion : this bit will flip the polarity of the re ceive cmi data inputs at rxp/n. for debug use only. 0: normal 1: invert 5 lolor r/w 0 receive loss of lock/signal override: when high, the rxlol and rxlos si gnals will always remain low. 0: normal 1: forces los and lol outputs to be low and resets counters note : for reliable operation of the rx lol detection circuitry, one must manually reset the lol counter by toggling this bit upon power-up or initialization. 4 rlbk r/w 0 3 llbk r/w 0 analog loopback selection : rlbk llbk 0 0 normal operation 1 0 remote loopback enable : recovered receive data is looped back to the transmit driver 0 1 local loopback enable : the transmit data is looped back and used as the input to the receiver. 2 rclkp r/w 0 receive clock inversion select : this bit will invert t he receive output clock. 0: normal . data clocked out on falling edge of receive clock. 1: invert . data clocked out on the rising edge of receive clock. 1 tclkp r/w 0 transmit clock inversion select : this bit will invert the transmit input system clock. 0: normal . data is clocked in on rising edge of the transmit clock. 1: invert . data is clocked in on the falling edge of the transmit clock. 0 frst r/w 0 fifo reset : 0: normal operation 1: reset fifo pointers to default locations. this reset should be initiated anytime the transmitter or ic powers up to ensure the fifo is centered after internal vco clocks and external transmit clocks are stable. notes : transmit monitor port will also be affected by frst, fifo resets not required for plesiochronous serial mode downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 15 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) address 1-2: advanced transmit control register 1 bit name type dflt value description 7:1 -- r/w 0000000 reserved. 0 txeq r/w 0 transmit fixed equalizer enable : when enabled, compensates for between 0.75m and 1.5m of fr4 trace to the serial lvpecl data inputs sidp/n 0: normal operation 1: enable equalizer address 1-3: advanced transmit control register 0 bit name type dflt value description 7:3 -- r/w 10101 reserved. 2:1 bst[1:0] r/w 00 transmit driver amplitude boost : adds roughly 5% or 10% of boost to the cmi output. limits not tested during production test. 00 : normal amplitude 01 : 5% boost 10 : reserved 11 : 10% boost 0 flbk r/w 0 full remote (digital) loopback enable : when enabled the recovered receive data is decoded and looped back to the transmit clock recovery unit exercising the entire receive and transmit paths. note : must be used in conjunction with serial plesiochronous mode or serial loop-timing mode. address 1-4: mode control register 2 bit name type dflt value description 7 cmi r/w 1 line interface mode selection : 0: optical fiber (lvpecl, nrz). cmi endec and line driver are disabled. use rxp/n and eclp/n pins for line interface. 1: coaxial cable (cmi encoded) . cmi endec enabled. optical (nrz) interface disabled. use rxp/n and cmip/n pins for line interface. 6:0 -- r/w xx00000 reserved. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 16 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 register description (continued) address 1-5: status monitor register bit name type dflt value description 7:5 -- r/c xxx reserved. 4 rxlos r/c x receive loss of signal indication : 0: normal operation 1: loss of signal condition detected 3 rxlol r/c x receive loss of lock indication : this status bit is only defined during a valid input signal at rp/n or when rxlos=0 0: normal operation 1: recovered receive clock frequency differs from the reference by more than +/- 100ppm. 2 -- r/c x unused 1 txlol r/c x transmit loss of lock indication : this status bit is only defined and valid when using one of the serial transmit modes utilizi ng the tx cdr. 0: valid transmit input signal detected at sidp/n 1: no valid signal detected at sidp/n 0 ferr r/c x transmit fifo error indication : this bit is set whenever the internal ferr signal is asserted, indicating that the fifo is operating at its dept h limit. it is reset to 0 when the frst pin is asserted. 0: normal operation 1: transmit fifo phase error address 1-6, 1-7: reserved bit name type dflt value description 7:0 rsvd r/o 0 reserved for test. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 17 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description legend type description type description a analog pin (tie unused pins to ground) po lvpecl-compatible differential output (tie unused pins to supply or leave floating) cis cmos schmitt trigger input (tie unused pins to ground) co cmos digital output (leave unused pins floating) ci cmos digital input (tie unused pins to ground) coz cmos tristate digital output (leave unused pins floating) ciu cmos digital input w/ pull-up od open-drain digital output (leave unused pins floating) cid cmos digital input w/ pull-down s supply cit 3-state cmos digital input g ground pi lvpecl-compatible differential input (tie unused pins to ground) transmitter pins name pin type description pi0d pi1d pi2d pi3d 24 25 26 27 ci transmit (parallel mode) data input : four-bit cmos parallel (nibble) inputs. data is latched in on the rising edge (default) of the transmit parallel cl ock and serialized with the msb (pix3d) transmitted first. pick 23 cis transmit (parallel mode) clock input : a 34.816 mhz (e4) or 38.88 mhz (stm1) cmos clock input that must be source synchronous with the reference clock supplied at the ckrefp/n pins. used only in slave parallel mode and loop-timing parallel mode. ptock 28 co transmit (parallel mode) clock output : a 34.816 mhz (e4) or 38.88 mhz (stm 1) cmos clock output that is intended to latch in synchronous parallel data. active during reset. used only in master parallel mode (output disabled in all other transmit modes). sidp sidn 8 9 pi transmit (serial mode) data input : differential nrz data input. see transmitter operation section for more info on different clocking/timing modes. sickp sickn 5 6 pi transmit (serial mode) clock input : a 155.52mhz synchronous differential input clock used to clock in the serial nrz data. by default, data is clock ed in on the rising edge of sickp. cmip cmin 93 94 a transmit (cmi mode) analog data output : a cmi encoded data signal output conforming to the relevant itu-t g.703 pulse templates when properly terminated and transformer coupled to 75 ? cable. outputs are tri-stated when transmitter is disabled. active, but undefined during reset. cmi2p cmi2n 79 78 a transmit monitor output : redundant cmi transmit driver enabled by rcsl control. txckp txckn 96 97 po transmit (serial mode) clock output : a 2x line rate lvpecl clock output used to clock out the transmit cmi data. used for diagnostics or far end re-timing. active during reset. eclp ecln 99 100 po transmit (optical mode) lvpecl data output : transmit data outputs used for interfac ing with optical transceiver modules when in fiber (nrz pass through) mode. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 18 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description (continued) receiver pins name pin type description po0d po1d po2d po3d 41 40 37 36 co receive data (parallel mode) output : recovered receive data de-serialized into four-bit cmos parallel (nibble) outputs. the msb (po3d) is received first. active, but undefined during reset. note : during loss of signal conditions, data outputs are held low. pock 33 co receive (parallel mode) clock output : a 34.816 mhz (e4) or 38.88 mhz (stm1) cmos clock output generated by dividing down the recovered receive cl ock. by default, receive data is clocked out on the falling edge. active during reset. note: during loss of signal conditions, the clock will remain on the last divided down phase selection of the rx dll and output a steady clock. sodp sodn 20 21 po receive (serial mode) data output : recovered receive serial nrz data at lvpecl levels. active, but undefi ned during reset. note : during loss of signal conditions, data outputs are held at logic 0. sockp sockn 18 19 po receive (serial mode) clock output : recovered receive serial clock. by default, recovered serial nrz data is clocked out the falling edge of sockp. active during reset. note: during loss of signal conditions, the clock will remain on the last phase selection of the rx d ll and output a steady clock. rxp rxn 90 91 a/ pi receiver (cmi or nrz) input : the input is either transformer-coupled to coaxial cable for cmi data or ac- coupled at lvpecl levels to an optic al transceiver module for nrz data. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 19 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description (continued) reference and status pins name pin type description ckrefp ckrefn 83 82 pi/ ci reference clock input : a required reference clock input used for clock/data recovery and frequency synthesizer. options include ? 139.264 mhz (e4) or 155.52 mhz (stm1) differential lvpecl clock input at ckrefp/n ? 17.408 mhz (e4), 19.44 mhz (stm1), or 77.78 mhz (stm1) single- ended cmos clock input at ckrefp . tie ckrefn to ground when unused. los 61 od receive loss of signal (active-high): see receiver loss of signal description for conditions. lol 60 od receive loss of lock (active-high): this condition is met when the recovered clock frequency differs from the reference clock frequency by more than +/- 100ppm. inttxb 67 od transmitter fault interrupt flag (active low): when a transmitter error event occurs (as defined in the interrupt control register description), the inttxb pin will change state to indicate an interrupt. the interrupt is cleared by a read to the stat register, an issue of a frst fifo reset pulse (if the fierr signal caused the interrupt), or when the txlol register bit transitions from high to low. note : the default interrupt condition is a loss of lock in the transmitter cdr. intrxb 52 od receiver fault interrupt flag (active-low): reserved for future use. porb 64 a power-on reset (active-low): see power-on reset description on use of this pin. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 20 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description (continued) control pins name pin type description frst 59 cit fifo phase-initialization control : when asserted, the transmit fifo po inters are reset to the respective centered states. also resets the fi err interrupt bit. de-assertion edge of frst will resume fifo operation. ? low : frst assertion. ? float/high : normal because the internal vco clock and off- chip transmit clocks may not be stable during transmit power-up, it is recommended to always reset the fifos after powering up the ic or the transmitter. not valid during plesiochronous serial mode. rcsl 14 cid redundant channel selection : enables the redundant transmit moni tor output at pins cmi2p/n. ? low : normal operation (cmip/n active only) ? high : transmit monitor mode (cmip/n and cmi2p/n active) lpbk 15 cit analog loopback selection : ? low : normal operation ? float : remote loopback enable: recovered receive data and clock are looped back to the transmitter for retransmission. ? high : local loopback enable: the serial transmit data is looped back and used as the input to the receiver. ckmode 13 cit clock mode selection : selects the method of inputting transmit data into the chip. see transmitter operation section for more information. in parallel mode (sdi_par high): ? low : parallel transmit clock is input to the 78p2351. ? float : parallel transmit clock is input to the 78p2351. loop-timing mode enabled. ? high : parallel transmit clock is output from the 78p2351 in serial mode (sdi_par low): ? low : reference clock is synchronous to transmit clock and data. data is clocked in with sickp/n and passed through a fifo ? float : reference clock is synchronous to transmit data. clock is recovered with a cdr and data is passed through a fifo ? high : reference clock is plesiochronous to transmit data. clock is recovered with a cdr and the fifo is bypassed downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 21 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description (continued) control pins (continued) name pin type description txout1 1 cit advanced tx control 1 : low : enables fixed lvpecl equalizer at the transmit inputs sidp/n for fr4 trace lengths up to 1.5m. float : normal operation high : normal operation txout0 2 cit advanced tx control 0 : low : nominal amplitude float : 5% amplitude boost high : 10% amplitude boost txpd 12 cid transmitter power down : when high, powers down and tri-states the transmit driver. the transmit monitor port, if enabled, is also powered down when txpd is high. spsl 58 cid serial port selection : when high, chip is software controlled through the serial port. cksl 62 cit reference clock frequency selection : selects the reference frequency that is su pplied at the ckrefp/n pins. its level is read in only at power-up or on the ri sing edge of a reset signal at the porb pin. ? low : 19.44mhz or 17.408mhz ? float : 77.76mhz ? high : 155.52mhz or 139.264mhz downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 22 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 pin description (continued) serial-port pins name pin type description sen_cmi 72 ciu [spsl=1] serial-port enable : high during read and write operations. low disables the serial port. while sen is low, sdo remains in high impedance state, and sdi and sck activities are ignored. [spsl=0] medium select : low: fiber (nrz pass-through) mode high: cmi mode sck_mon 73 cis [spsl=1] serial clock : controls the timing of sdi and sdo. [spsl=0] receive monitor mode enable : when high, adds 20db of flat gain to the incoming signal before equalization. rx monitor mode is only available in cmi mode. sdi_par 71 ci [spsl=1] serial data input : inputs mode and address information. also inputs register data during a write operation. both address and data are input least significant bit first. [spsl=0] data width select : selects 4 bit parallel transmit modes (input high) or serial transmit modes (input low) sdo_e4 70 coz/ ci [spsl=1] serial data output : outputs register information during a read operation. data is output least significant bit first [spsl=0] rate select : selects e4 operation (input high) or stm1/sts3 operation (input low) power and ground pins it is recommended that all supply pins be connected to a single power supply plane and all ground pins be connected to a single ground plane. see application note for decoupling guidelines. name pin type description vcc 3, 10, 16, 56, 66, 69, 76, 80, 88, 92, 98 s power supply vdd 31, 35, 39, 43 s cmos i/o driver supply gnd 4, 11, 17, 55, 65, 68, 77, 84, 85, 86, 87, 89, 95 g ground vss 30, 34, 38, 42 g cmos i/o driver ground tgnd 63 g trim ground used during production test. connect directly to ground. do not decouple to supply or porb. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 23 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications absolute maximum ratings operation beyond these limits may permanently damage the device. parameter rating supply voltage (vdd) -0.5 to 4.0 vdc storage temperature -65 to 150 c junction temperature -40 to 150 c pin voltage (cmixp,cmixn) vdd + 1.5 vdc pin voltage (all other pins) -0.3 to (vdd+0.6) vdc pin current 100 ma recommended operating conditions unless otherwise noted all specifications are valid over these temperatures and supply voltage ranges. parameter rating dc voltage supply (vdd) 3.15 to 3.45 vdc ambient operating temperature -40 to 85 c junction temperature -40 to 125 c dc characteristics: parameter symbol conditions min nom max unit iddm stm-1 mode; cmi mode; max. cable length; tx monitor enabled 190 212 ma supply current (cmi) (including transmitter current through transformer) idd stm-1 mode; cmi mode; max. cable length; tx monitor disabled 160 180 ma supply current (nrz) idde stm-1 mode; nrz (optical) mode; 145 160 ma receive-only supply current iddr transmitter disabled; stm-1 mode; cmi mode; max. cable length; 92 106 ma power down current iddq pdtx=1, pdrx=1 7 10 ma downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 24 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) analog pins characteristics: the following table is provided for informat ive purpose only. not tested in production. parameter symbol conditions min nom max unit rxp and rxn common-mode bias voltage vblin ground reference 1.9 2.1 2.6 v rxp and rxn differential input impedance rilin 20 k ? analog input/output capacitance cin 8 pf porb input impedance -- 5 k ? digital i/o characteristics: pins of type ci, ciu, cid: parameter symbol conditions min nom max unit type ci, cid only 0.8 input voltage low vil type ciu only 0.4 v input voltage high vih 2.0 v input current iil, iih -1 0 1 a pull-up resistance rpu type ciu only 53 70 113 k ? pull-down resistance rpd type cid only 40 58 120 k ? input capacitance cin 8 pf pins of type cit : parameter symbol conditions min nom max unit input voltage low vtil 0.4 v input voltage high vtih vcc-0.6 v minimum impedance to be considered as float state rtiz 30 k ? pins of type cis: parameter symbol conditions min nom max unit low-to-high threshold vt+ 1.3 1.7 v high-to-low threshold vt- 0.8 1.2 v input current iil, iih -1 1 a input capacitance cin 8 pf downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 25 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) pins of type co and coz: parameter symbol conditions min nom max unit output voltage low vol iol = 8ma 0.4 v output voltage high voh ioh = -8ma 2.4 v output transition time tt c l = 20pf 2 ns effective source impedance rscr 30 ? tri-state output leakage current iz type coz only -1 1 a pins of type po: parameter symbol conditions min nom max unit 0.5 0.8 1.1 signal swing vpk txxckp/n pins 0.35 0.95 v common mode level vcm vdd referenced -1.55 -1.2 -1.1 v effective source impedance reff 20 ? rise time tr 10-90% 0.8 1.2 ns fall time tf 10-90% 0.8 1.2 ns pins of type pi : parameter symbol conditions min nom max unit signal swing vpki 0.3 v common mode level vcm vdd referenced -1.6 -1.2 -0.8 v pins of type od parameter symbol conditions min nom max unit output voltage low vol iol = 8ma 0.4 v pull-down leakage current ipd logic high output 1 a pull-up resistor rpu 4.7 10 k ? downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 26 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) serial-port timing characteristics: parameter symbol conditions min typ max unit sdi to sck setup time tsu 4 ns sdi to sck hold time th 4 ns sck to sdo propagation delay tprop 10 ns sck frequency sck 20 mhz 1 sa0 sa1 sa2 pa0 pa1 pa2 pa3 z cs sck sdi sdo t su t h x x or z t su t h d0 d1 d2 d3 d4 d5 d6 d7 z t prop figure 10: read operation figure 11: write operation 0 sa0 sa1 sa2 pa0 pa1 pa2 pa3 d0 d1 d2 d3 d4 d5 d6 d7 z cs sck sdi sdo t su t h x x t su t h downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 27 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) transmitter timing characteristics: parameter symbol conditions min nom max unit clock duty cycle ttcf/ttc ptock 40 60 % setup time tps parallel mode 4 ns hold time tph parallel mode 4 ns setup time tss serial mode 2 ns hold time tsh serial mode 2 ns timing diagram: transmitter waveforms tsh tss sickn sickp sidp sidn pick pixd<0:3> tph tps ptock pixd<0:3> tph tps ttct trc = 25.72ns trcf = 12.86ns downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 28 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) reference clock characteristics: parameter symbol conditions min nom max unit ckref duty cycle -- 40 60 % synchronous mode; e4 -15 +15 synchronous mode; stm1 -20 +20 ckref frequency stability -- plesiochronous or loop-timing mode. (see note 1) -75 +75 ppm note 1 : in plesiochronous mode, the transmit clock/data so urce (i.e. framer/system reference clock) must still be of +/-20ppm quality (+/-15ppm for e4) in order to meet the itu-t (or telcordia) bit rate requirements. receiver timing characteristics: parameter symbol conditions min nom max unit rclk duty cycle trcf/trc 40 60 % rscq serial mode 0 1 clock to q rpcq parallel mode -1 2 ns timing diagram: receive waveforms trc = 6.43ns trcf = 3.215ns rscq sockn sockp sodp sodn trct pock poxd<0:3> trc = 25.72ns trcf = 12.86ns rpcq trct downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 29 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) transmitter specifications for cmi interface bit rate : 139.264 mbps 15ppm or 155.52 mbps 20ppm code : coded mark inversion (cmi) relevant specifications : itu-t g.703, telcordia gr-253, ansi t1.102 with the coaxial output port driving a 75 ? load, the output pulses conform to the templates in figures 12, 13, 14 and 15. these specifications are tested during production test. consult application note for reference schematic, layout guidelines, and recommended transformers. parameter condition min nom max unit peak-to-peak output voltage (fuse-trimmed to nominal target at final test) template, steady state 0.9 1.05 1.1 v rise/ fall time 10-90% 2 ns negative transitions -0.1 0.1 positive transitions at interval boundaries -0.5 0.5 transition timing tolerance positive transit ions at mid- interval -0.35 0.35 ns transmit clock frequency stability (pick or sickp/n ) with respect to ckref 0 0 ppm the following specifications are not tested during production test. they are included for information only. parameter condition min nom max unit output impedance driver is open drain 1 8 m ? pf return loss 7mhz to 240mhz 15 db downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 30 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) (note 1) (note 1) (note 1) 0.60 0.55 0.50 0.45 0.40 0.05 -0.05 -0.50 -0.55 -0.60 -0.45 -0.40 (note 1) 0.35ns nominal zero level (note 2) t = 7.18ns 0.1ns 0.1ns 1ns 1.795 ns 1.795 ns 1.795 ns 1.795 ns 1ns 1ns 1ns 0.1ns 0.1ns 1ns 1ns nominal pulse 0.35ns v note 1 C the maximum steady state amplitude should not exceed the 0.55v limit. overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55v and 0.6v, provided that they do not exceed the steady state level by more than 0.05v. note 2 C for all measurements using these masks, the signal should be ac coupled, using a capacitor of not less than 0.01 f, to the input of the oscilloscope used for measurements. the nominal zero level for both masks should be aligned with the oscilloscope trace wit h no input signal. with the signal then applied, the vert ical position of the trace can be adjusted with the objective of meeting the limi ts of the masks. any such adjustment should be the same for both masks and should not exceed 0.05v. this may be checked by removing the input signal again and verifying that the trace lies with 0.05v of the nominal zero level of the masks. note 3 C each pulse in a coded pulse sequence should meet the limit s of the relevant mask, irrespective of the state of the pre ceding or succeeding pulses, with both pulse masks fixed in the same relati on to a common timing reference, i.e. with their nominal start and finish edges coincident. the masks allow for hf jitter caused by intersym bol interference in the output stage, but not for jitter pres ent in the timing signal associated with the source of the interface signal. w hen using an oscilloscope technique to determine pulse compliance w ith the mask, it is important that successive traces of the pulses overlay in order to suppress t he effects of low frequency jitter. this can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the meas ured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. note 4 C for the purpose of these masks, the rise time and decay time should be measured between C0.4v and 0.4v, and should not exceed 2ns. figure 12 C mask of a pulse corresponding to a binary zero in e4 mode downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 31 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) (note 1) (note 1) 0.600.55 0.50 0.45 0.40 0.05 -0.05-0.50 -0.55 -0.60 -0.45 -0.40 (note 1) nominal zero level (note 2) t = 7.18ns 0.1ns 0.1ns 1ns 1.795 ns 1ns nominal pulse v 3.59ns 1.35ns 1.35ns 3.59ns 1.795 ns 1ns 1ns 0.5ns 0.5ns note 1 C the maximum steady state amplitude should not exc eed the 0.55v limit. overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55v and 0.6v, provided that they do not exceed the steady state level by more than 0.05v. note 2 C for all measurements using these masks, the signal should be ac coupled, using a capacitor of not less than 0.01 f, to the input of the oscilloscope used for measurements. the nominal zero level for both masks should be aligned with the oscilloscope trace wit h no input signal. with the signal then applied, the vert ical position of the trace can be adjusted with the objective of meeting the limi ts of the masks. any such adjustment should be the same for both masks and should not exceed 0.05v. this may be checked by removing the input signal again and verifying that the trace lies with 0.05v of the nominal zero level of the masks. note 3 C each pulse in a coded pulse sequence should meet the limit s of the relevant mask, irrespective of the state of the pre ceding or succeeding pulses, with both pulse masks fixed in the same relati on to a common timing reference, i.e. with their nominal start and finish edges coincident. the masks allow for hf jitter caused by intersym bol interference in the output stage, but not for jitter pres ent in the timing signal associated with the source of the interface signal. w hen using an oscilloscope technique to determine pulse compliance w ith the mask, it is important that successive traces of the pulses overlay in order to suppress t he effects of low frequency jitter. this can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the meas ured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. note 4 C for the purpose of these masks, the rise time and decay time should be measured between C0.4v and 0.4v, and should not exceed 2ns. note 5 Cthe inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive transitions are 0.1ns and 0.5ns respectively. figure 13 C mask of a pulse corresponding to a binary one in e4 mode. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 32 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) (note 1) (note 1) (note 1) 0.600.55 0.50 0.45 0.40 0.05 -0.05-0.50 -0.55 -0.60 -0.45 -0.40 (note 1) 0.35ns nominal zero level (note 2) t = 6.43ns 0.1ns 0.1ns 1ns 1.608ns 1.608ns 1.608ns 1.608ns 1ns 1ns 1ns 0.1ns 0.1ns 1ns 1ns nominal pulse 0.35ns v note 1 C the maximum steady state amplitude should not exceed the 0.55v limit. overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55v and 0.6v, provided that they do not exceed the steady state level by more than 0.05v. note 2 C for all measurements using these masks, the signal should be ac coupled, using a capacitor of not less than 0.01 f, to the input of the oscilloscope used for measurements. the nominal zero level for both masks should be aligned with the oscilloscope trace wit h no input signal. with the signal then applied, the vert ical position of the trace can be adjusted with the objective of meeting the limi ts of the masks. any such adjustment should be the same for both masks and should not exceed 0.05v. this may be checked by removing the input signal again and verifying that the trace lies with 0.05v of the nominal zero level of the masks. note 3 C each pulse in a coded pulse sequence should meet the limit s of the relevant mask, irrespective of the state of the pre ceding or succeeding pulses, with both pulse masks fixed in the same relati on to a common timing reference, i.e. with their nominal start and finish edges coincident. the masks allow for hf jitter caused by intersym bol interference in the output stage, but not for jitter pres ent in the timing signal associated with the source of the interface signal. w hen using an oscilloscope technique to determine pulse compliance w ith the mask, it is important that successive traces of the pulses overlay in order to suppress t he effects of low frequency jitter. this can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the meas ured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. note 4 C for the purpose of these masks, the rise time and decay time should be measured between C0.4v and 0.4v, and should not exceed 2ns. figure 14 C mask of a pulse corresponding to a binary zero in stm-1/sts-3 mode. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 33 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) (note 1) (note 1) 0.600.55 0.50 0.45 0.40 0.05 -0.05-0.50 -0.55 -0.60 -0.45 -0.40 (note 1) nominal zero level (note 2) 6.43ns 0.1ns 0.1ns 1ns 1.608ns 1ns nominal pulse v 3.215ns 1.2ns 1.2ns 3.215ns 1.608ns 1ns 1ns 0.5ns 0.5ns note 1 C the maximum steady state amplitude should not exceed the 0.55v limit. overshoots and other transients are permitted to fall into the shaded area bounded by the amplitude levels 0.55v and 0.6v, provided that they do not exceed the steady state level by more than 0.05v. note 2 C for all measurements using these masks, the signal should be ac coupled, using a capacitor of not less than 0.01 f, to the input of the oscilloscope used for measurements. the nominal zero level for both masks should be aligned with the oscilloscope trace wit h no input signal. with the signal then applied, the vert ical position of the trace can be adjusted with the objective of meeting the limi ts of the masks. any such adjustment should be the same for both masks and should not exceed 0.05v. this may be checked by removing the input signal again and verifying that the trace lies with 0.05v of the nominal zero level of the masks. note 3 C each pulse in a coded pulse sequence should meet the limit s of the relevant mask, irrespective of the state of the pre ceding or succeeding pulses, with both pulse masks fixed in the same relati on to a common timing reference, i.e. with their nominal start and finish edges coincident. the masks allow for hf jitter caused by intersym bol interference in the output stage, but not for jitter pres ent in the timing signal associated with the source of the interface signal. w hen using an oscilloscope technique to determine pulse compliance w ith the mask, it is important that successive traces of the pulses overlay in order to suppress t he effects of low frequency jitter. this can be accomplished by several techniques [e.g. a) triggering the oscilloscope on the meas ured waveform or b) providing both the oscilloscope and the pulse output circuits with the same clock signal]. note 4 C for the purpose of these masks, the rise time and decay time should be measured between C0.4v and 0.4v, and should not exceed 2ns. note 5 Cthe inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive transitions are 0.1ns and 0.5ns respectively. figure 15 C mask of a pulse corresponding to a binary one in stm-1/sts-3 mode downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 34 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) transmitter output jitter the transmit jitter specification ensures compliance with itu-t g.813, g.823, g.825 and g.958; ansi t1.102- 1993 and t1.105.03-1994; and gr-253-core for all supported rates. transmit output jitter is not tested during production test. parameter condition min nom max unit cmi mode; 200 hz to 3.5 mhz, measured with respect to ckref for 60s 0.075 uipp transmitter output jitter nrz (optical) mode; 12 khz to 1.3 mhz, measured with respect to ckref 0.01 uirms transmitter output jitter detector measured jitter a mplitude f1 f2 20db/decade downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 35 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) receiver specifications for cmi interface (transformer-coupled) consult application note for reference schematic, layout guidelines, and recommended transformers. parameter condition min typ max unit peak differential input amplitude, rxp and rxn cmi mode; mon=0; 12.7db of cable loss 70 550 mvpk peak differential input amplitude, rxp and rxn cmi mode; mon=1; 20db flat loss w/ 6db of cable loss 25 80 mvpk flat-loss tolerance cmi mode; mon=0; all valid cable lengths. -2 6 db receive clock jitter stm-1 mode; cmi mode; 12.7 db cable loss a) normal receive mode b) remote loopback mode 0.1 0.07 uipp uipp latency 5 10 ui pll lock time 1 10 s return loss 7mhz to 240mhz 15 db the input signal is assumed compliant with itu-t g.703 and can be attenuated by the dispersive loss of a cable. the minimum cable loss is 0db a nd the maximum is C12.7db at 78mhz. the worst case line corresponds to the itu-t g.703 recommendation. the typical line corresponds to a typical installation referred to in ansi t1.102-1993. the receiver is tested using the cable model. it is a lumped element approximation of the worst case line. 0 5 10 15 20 25 30 1.00e+05 1.00e+06 1.00e+07 1.00e+08 1.00e+09 frequency (hz) attenuation (db) worst case typical figure 16: typical and worst-case cable attenuation downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 36 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) receiver jitter tolerance the 78p2351 exceeds all relevant jitter tolerance specif ications shown in figures 17, 18. sts-3/oc-3 jitter tolerance specifications are in ansi t1.105.03-19 94 and telcordia gr-253-core. stm-1 (optical) jitter tolerance specifications are in itu-t g.813, g.825, and g.958. stm-1e (electrical) jitter tolerance specifications are in itu-t g.825. e4 specifications are found in itu-t g.823. receive jitter tolerance is not tested during production test. 0.01 0.1 1 10 100 1.e+00 10hz 100hz 1khz 10khz 100khz 1mhz 10mhz electrical (cmi) interfaces g.825 - stm-1e tolerance (for 2048 kbps networks) g.825 - stm-1e tolerance (for 1544 kbps networks) jitter frequency jitter tolerance ( uipp ) g.823 - e4 tolerance figure 17: jitter tolerance - electrical (cmi) interfaces parameter condition min nom max unit 200hz to 500hz 1.5 uipp 500hz to 10khz 750 f-1 s e4 jitter tolerance 10khz to 3.5mhz 0.075 uipp 10hz to 19.3hz 38.9 uipp 19.3hz to 500hz 750 f-1 s 500hz to 6.5khz 1.5 uipp 6.5khz to 65khz 9800 f-1 s stm-1e jitter tolerance 65khz to 1.3mhz 0.15 uipp downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 37 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) 0.01 0.1 1 10 100 1.e+00 10hz 100hz 1khz 10khz 100khz 1mhz 10mhz optical (nrz) interfaces g.813, g.958, t1.105.03, gr-253 stm-1 / sts-3 / oc-3 tolerance g.825 - stm-1 tolerance jitter frequency jitter tolerance ( uipp ) figure 18: jitter tolerance - optical (nrz) interfaces parameter condition min nom max unit 10hz to 19.3hz 38.9 uipp 19.3hz to 68.7hz 750 f-1 s 68.7hz to 6.5khz 1.5 uipp 6.5khz to 65khz 9800 f-1 s oc-3/sts-3/stm-1 (optical) jitter tolerance 65khz to 1.3mhz 0.15 uipp downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 38 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) receiver jitter transfer function the receiver clock recovery loop filter characteristics such that the receiver has the following transfer function. the corner frequency of the rx dll is approximately 120 khz. receiver jitter transfer function is not tested during production test. -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1.00e+03 1.00e+04 1.00e+05 1.00e+06 1.00e+07 figure 19: jitter transfer parameter condition min nom max unit receiver jitter transfer function below 120 khz 0.1 db jitter transfer function roll-off 20 db per decade downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 39 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 electrical specifications (continued) cmi mode loss of signal condition parameter condition min typ max unit los threshold -35 -19 -15 db los timing 10 110 255 ui nominal value maximum cable loss loss of signal must be cleared loss of signal must be declared tolerance range los can be detected or cleared 3 db 15db 35db application information external components: component pin(s) value units tolerance receiver termination resistor, cmi mode rxp rxn 75 ? 1% transmitter termination resistor, cmi mode cmip cmin 75 ? 1% (cmi) transformer specifications: component value units tolerance turns ratio for the receiver 1:1 turns ratio for the transmitter (center-tapped) 1:1ct suggested manufacturers: halo, tamura, minicircuits, belfuse thermal information: package conditions ja ( ? c/w) standard 100-pin jedec lqfp no forced air; 4-layer jedec test board 46 schematics for reference schematics, layout guidelines, recommended transformer part numbers, etc. please check teridian semiconductor's website or contact your local sales repres entative for the latest application note(s) and/or demo board manuals. downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 40 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 mechanical specifications 1 0.50(0.020)typ. 0.05(0.002) 0.15(0.006) 0.18(0.007) 0.27(0.011) 0.60(0.024) typ. 13.80 (0.543) 14.20 (0.559) 15.70 (0.618) 16.30 (0.641) 15.70 (0.618) 16.30 (0.641) 1.40(0.055) 1.60(0.063) top view side view 100-pin jedec lqfp (top view) downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 41 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 package information (top view) 12 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 19 20 21 22 23 24 25 2627 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 6362 61 60 59 58 57 56 55 54 53 52 51 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 n/c ecln eclp vcc txckn txckp gnd cmin cmip vcc rxn rxp gnd vcc gnd gnd gnd gnd ckrefp vcc cmi2p cmi2n gnd vcc ckrefn po1d n/c n/c n/c n/c n/c n/c n/c vdd vss po0d vdd po2d vss po3d vdd vss pock vdd vss n/c ptock pi3d n/c pi2d txout1 txout0 vcc gnd vcc sidn sodn pick pi0d pi1d sickp sickn n/c sidp n/c vcc gnd txpd ckmode sockp gnd sockn sodp lpbk rcsl tgnd porb cksl los gnd sdi_par sdo_e4 n/c n/c sck_mon sen_cmi lol frst spsl inttxb vcc gnd gnd n/c n/c intrxb n/c vcc vcc n/c 78p2351 ordering information part description order number package mark 100-pin lqfp; revision a06 78p2351-igt 78p2351-igt xxxxxxxxxxp6 tape & reel option append r n/a lead-free option append /f xxxxxxx-xxx xxxxxxxxxxp6f downloaded from: http:///
78p2351 single channel oc-3/ stm1-e/ e4 liu page: 42 of 42 ? 2006 teridian semiconductor corporation rev. 2.4 revision history -- contact teridian for revision history of earlier releases v2-0 march 14, 2005: final datasheet release updated ordering numbers to reflect production silicon revision a06 o obsoleted 70pxxxx option (cmos output type status & interrupt pins) improved/modified functional descriptions for: o reference clock, rx los & lol detecto rs, synchronous (re-timing) transmit modes, tx fifo, tx driver, tx lol det ector, and power-on reset description improved/modified register descriptions for: o xcmiinv invert bits, frst, rxlol, and txlol improved/modified pin descriptions for: o ptock, frst, sen_cmi, gnd pin 63 updated electrical specification min/max limits for: o dc characteristics, o cid, ciu, cit, and po pin types o cmi loss of signal conditions v2-2 august 12, 2005 : changed name and logo from tdk to teridian updated rx and tx loss of lock descriptions added full remote (digital) loopback and update remote (analog) loopback descriptions v2-3 august 15, 2006 updated ordering numbers to remove silicon revision a06 updated package mark from c6 to p6 v2-4 september 20, 2006 corrected several typos in the mechanical drawing if and when manufactured and sold, this product is sold subject to the terms and conditions of sale supplied at the time of ord er acknowledgment, including those pertaining to warranty, patent in fringement and limitation of li ability. teridian semiconduct or corporation (tsc) reserves the right to make changes in specifications at any time without notic e. accordingly, the reader is cautioned to verify that a data sheet is current before placing orders. ts c assumes no liability for applications assistance. teridian semiconductor corp., 6440 oak canyon, irvine, ca 92618 tel (714) 508-8800, fax (714) 508-8877, http://www.teridiansemiconductor.com downloaded from: http:///


▲Up To Search▲   

 
Price & Availability of 78P2351-DB-ECLM

All Rights Reserved © IC-ON-LINE 2003 - 2022  
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]
 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X