1 1-35 model 64 electrical standard resistance range, ohms 10 to 1meg standard resistance tolerance ?0% input voltage, maximum 200vdc or rms not to exceed power rating slider current, maximum 100ma or within rated power, whichever is less power rating, watts 0.25 at 85? derating to 0 at 150? end resistance, maximum 2 ohms actual electrical travel, turns, nominal 12 dielectric strength 900vrms insulation resistance, minimum 1,000 megohms resolution essentially infinite contact resistance variation, maximum 1% or 1 ohms, whichever is greater environmental seal 85? fluorinert?(no leaks) temperature coefficient, maximum ?00ppm/? operating temperature range ?5? to +150? thermal shock 5 cycles, ?5? to +150? (1% ? rt, 1% ? vr) moisture resistance ten 24 hour cycles (1% ? rt, ir 1,000 megohms min.) shock, 6ms sawtooth 100g? (1% ? rt, 1% ? vr) vibration 20g?, 10 to 2,000 hz (1% ? rt, 1% ? vr) high temperature exposure 250 hours at 125? (2% ? rt, 2% ? vr) rotational life 200 cycles (2% ? rt) load life at 0.25 watts 1,000 hours at 85? (2% ? rt) resistance to solder heat 260? for 10 sec. (1% ? rt) mechanical mechanical stops clutch action, both ends torque, starting maximum 3 oz.-in. (0.021 n-m) weight, nominal .014 oz. (0.40 grams) model 64 1/4?square multiturn cermet trimming potentiometer fluorinert?is a registered trademark of 3m company. specifications subject to change without notice.
.10 2.54 .02 0.51 .10 2.54 .10 2.54 c l schematic diagram this surface model 64w model 64 1-36 top adjustment (inch/mm) .070 .005 1.78 0.13 .020 0.51 .050 .040 1.02 1.27 .040 1.02 .020 0.51 .172 4.37 .270 .020 6.86 0.51 .018 .002 0.46 .05 .020 0.51 .165 .020 4.19 0.51 .250 .020 6.35 .0.51 metal adjustment screw dia. with slot wide x standard marking on this surface min. min. 123 terminal pins (3) solderable min. min. deep model 64w and 64y .10 2.54 .092 2.34 .10 2.54 c l model 64y standard resistance values, ohms 10 100 1k 10k 50k 250k 20 200 2k 20k 100k 500k 50 500 5k 25k 200k 1meg note: model 64w dimensions applicable to all models except as noted.
model 64 1-37 standard marking on this surface min. .172 4.37 .040 1.02 .250 .020 6.35 0.51 .175 .020 4.45 0.51 .250 .020 6.35 0.51 0.15 0.38 .10 2.54 .10 2.54 .10 2.54 c l c l 1 2 3 model 64p .10 2.54 .092 2.34 .10 2.54 c l model 64z side adjustment (inch/mm) standard marking on this surface .040 1.02 .050 1.27 12 3 .040 1.02 .10 2.54 .10 2.54 .10 2.54 schematic diagram this surface .02 0.51 c l model 64x model 64x and 64z 1
1-38 model 64 packaging ordering information 64 p r 10k lf model series pin style rohs compliant product code - optional resistance value resistance prefix 64 y f r 10k lf xx pin style pin style suffix (used with ap & tr packaging options. "f" designates 0.6" min. lead length.) packaging option ap = ammo pack tr = tape & reel (no code used for tubes) rohs compliant product code - optional standard: option: standard: tubes all units oriented with #1 pin to same side. pin style p,w,y x,z magazine width = 0.38?(9.65 mm) 0.38?(9.65 mm) height = 0.62?(15.75mm) 0.62?(15.75mm) length = 14.5?(368 mm) 16.9?(429 mm) capacity = 50 units 50 units option: tape & reel, ammo pack (available only for 64y and 64z) all units oriented with #1 pin to the right of the direction of feed. seat plane to centerline of sprocket hole = .71?(18 mm) tape width = 18 mm sprocket = single hole .50?spacing capacity = 1,000 units reel diameter = 14?(363 mm) ammo tape fold = 12 box = 1.8?x 13?x 10 (46mm x 330mm x 254mm) metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original. english units and are provided for general information only. tolerances unless otherwise specified: linear = .01 inches (.25mm) angular = 2 degrees circuit diagram (1) (2) (3) cw notes mm inch
|
