View HLSR10-P-SP33_8591594.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

page 1/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com features open loop multi-range current transducer voltage output galvanic separation between primary and secondary low power consumption compact design for through-hole pcb mounting factory calibrated high bandwidth, very low loss magnetic core. special feature single supply +3.3 v. advantages extremely low profle: h = 12 mm low foot-print low offset drift over-drivable v ref . applications ac variable speed and servo motor drives static converters for dc motor drives battery supplied applications uninterruptible power supplies (ups) switched mode power supplies (smps) power supplies for welding applications combiner box mppt. standards en 50178: 1997 iec 61010-1: 2010 iec 61326-1: 2012 ul 508: 2010. application domain industrial. current transducer hlsr-p/sp33 series i pn = 10 ... 50 a ref: hlsr 10-p/sp33, hlsr 20-p/sp33, hlsr 32-p/sp33, hlsr 40-p/sp33, hlsr 50-p/sp33 for the electronic measurement of current: dc, ac, pulsed..., with galvanic separation between the primary and the secondary circuit. n97.j3.13.033.0, n97.j3.17.033.0, n97.j3.j3.033.0, n97.j3.23.033.0, n97.j3.25.033.0
page 2/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com absolute maximum ratings parameter symbol unit value supply voltage (not destructive) u c v 8 supply voltage (not entering non standard modes) u c v 6.5 primary conductor temperature t b c 120 esd rating, human body model (hbm) u esd kv 2 stresses above these ratings may cause permanent damage. exposure to absolute maximum ratings for extended periods may degrade reliability. ul 508: ratings and assumptions of certifcation file # e189713 volume: 2 section: 5 standards csa c22.2 no. 14-10 industrial control equipment - edition 11 - revision date 2011/08/01 ul 508 standard for industrial control equipment - edition 17 - revision date 2010/04/15 ratings parameter symbol unit value primary involved potential v ac/dc 600 max surrounding air temperature t a c 105 primary current i p a according to series primary current secondary supply voltage u c v dc 5 output voltage v out v 0 to 5 conditions of acceptability 1 - these devices have been evaluated for overvoltage category iii and for use in pollution degree 2 environment. 2 - a suitable enclosure shall be provided in the end-use application. 3 - the terminals have not been evaluated for feld wiring. 4 - these devices are intended to be mounted on a printed wiring board of end use equipment. the suitability of the connections (including spacings) shall be determined in the end-use application. 5 - primary terminals shall not be straightened since assembly of housing case depends upon bending of the terminals. 6 - any surface of polymeric housing have not been evaluated as insulating barrier. 7 - low voltage control circuit shall be supplied by an isolating source (such as a transformer, optical isolator, limiting impedance or electro-mechanical relay). marking only those products bearing the ur mark should be considered to be listed or recognized and covered under ul's follow-up service. always look for the mark on the product. hlsr-p/sp33 series
page 3/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com insulation coordination parameter symbol unit value comment rms voltage for ac insulation test 50/60 hz/1 min u d kv 4.3 impulse withstand voltage 1.2/50 s ? w kv 8 clearance (pri. - sec.) d ci mm > 8 shortest distance through air creepage distance (pri. - sec.) d cp mm > 8 shortest path along device body clearance (pri. - sec.) - mm 8 when mounted on pcb with recommended layout case material - - v0 according to ul 94 comparative tracking index cti 600 application example - - 600 v cat iii pd2 reinforced insulation, non uniform feld according to en 50178, iec 61010 application example - - 1000 v cat iii pd2 simple insulation, non uniform feld according to en 50178, iec 61010 application example - - 600 v cat iii pd2 according to ul 508 environmental and mechanical characteristics parameter symbol unit min typ max comment ambient operating temperature t a c ?40 105 ambient storage temperature t s c ?40 105 mass m g 5 hlsr-p/sp33 series
page 4/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com electrical data hlsr 10-p/sp33 at t a = 25 c, u c = +3.3 v, r l = 10 k? unless otherwise noted (see min, max, typ. defnition paragraph in page 9). parameter symbol unit min typ max comment primary nominal rms current i pn a 10 primary current, measuring range i pm a ?25 25 for u c = 3.3 v 5 % number of primary turns n p - 1 resistance of primary jumper @ t a = 25 c r p m? 0.21 resistance of primary jumper @ t a = 105 c r p m? 0.29 t jumper = 120 c supply voltage u c v 3.135 3.3 3.465 current consumption i c ma 19 25 reference voltage (output) v ref v 1.63 1.65 1.67 internal reference reference voltage (input) v ref v 0.5 1.7 external reference output voltage range @ i pm v out ? v ref v ?1.15 1.15 over operating temperature range v ref output resistance r ref ? 130 200 300 series v out output resistance r out ? 2 5 series capacitive loading c l nf 0 6 electrical offset voltage @ i p = 0 v oe mv ?5 5 v out ? v ref electrical offset current referred to primary i oe ma ?109 109 temperature coeffcient of v ref tcv ref ppm/k ?150 150 ?40 c 105 c temperature coeffcient of v oe tcv oe mv/k ?0.075 0.075 temperature coeffcient of i oe tci oe ma/k ?1.63 1.63 theoretical sensitivity g th mv/a 46 460 mv @ i pn sensitivity error g % ?0.5 0.5 factory adjustment temperature coeffcient of g tcg ppm/k ?200 200 linearity error 0 i pn l % of i pn ?0.5 0.5 linearity error 0 i pm l % of i pm ?0.8 0.8 magnetic offset current (@ 10 i pn ) referred to primary i om a ?0.25 0.25 reaction time @ 10 % of i pn t ra s 2 @ 50 a / s response time @ 90 % of i pn t r s 2.5 @ 50 a / s frequency bandwidth (?3 db) bw khz 450 output rms voltage noise spectral density 100 hz 100 khz e no v / hz 16 output voltage noise dc 10 khz dc 100 khz dc 1 mhz v no mvpp 9 22 40 accuracy @ i pn x % of i pn ?1 1 accuracy @ i pn @ t a = +85 c x 85 c % of i pn ?3.2 3.2 see formula note 1) accuracy @ i pn @ t a = +105 c x 105 c % of i pn ?3.9 3.9 see formula note 1) note : 1) accuracy @ t a (% of i pn ) = x + ( (t a ?25) + 100 ( t a ?25)). tcg 10000 tci oe 1000 i pn hlsr-p/sp33 series
page 5/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com electrical data hlsr 20-p/sp33 at t a = 25 c, u c = +3.3 v, r l = 10 k? unless otherwise noted (see min, max, typ. defnition paragraph in page 9). parameter symbol unit min typ max comment primary nominal rms current i pn a 20 primary current, measuring range i pm a ?50 50 for u c = 3.3 v 5 % number of primary turns n p - 1 resistance of primary jumper @ t a = 25 c r p m? 0.21 resistance of primary jumper @ t a = 105 c r p m? 0.29 t jumper = 120 c supply voltage u c v 3.135 3.3 3.465 current consumption i c ma 19 25 reference voltage (output) v ref v 1.63 1.65 1.67 internal reference reference voltage (input) v ref v 0.5 1.7 external reference output voltage range @ i pm v out ? v ref v ?1.15 1.15 over operating temperature range v ref output resistance r ref ? 130 200 300 series v out output resistance r out ? 2 5 series capacitive loading c l nf 0 6 electrical offset voltage @ i p = 0 v oe mv ?5 5 v out ? v ref electrical offset current referred to primary i oe ma ?217 217 temperature coeffcient of v ref tcv ref ppm/k ?150 150 ?40 c 105 c temperature coeffcient of v oe tcv oe mv/k ?0.075 0.075 temperature coeffcient of i oe tci oe ma/k ?3.26 3.26 theoretical sensitivity g th mv/a 23 460 mv @ i pn sensitivity error g % ?0.5 0.5 factory adjustment temperature coeffcient of g tcg ppm/k ?200 200 linearity error 0 i pn l % of i pn ?0.5 0.5 linearity error 0 i pm l % of i pm ?0.8 0.8 magnetic offset current (@ 10 i pn ) referred to primary i om a ?0.25 0.25 reaction time @ 10 % of i pn t ra s 2 @ 50 a / s response time @ 90 % of i pn t r s 2.5 @ 50 a / s frequency bandwidth (?3 db) bw khz 450 output rms voltage noise spectral density 100 hz 100 khz e no v / hz 8 output voltage noise dc 10 khz dc 100 khz dc 1 mhz v no mvpp 6 13 23 accuracy @ i pn x % of i pn ?1 1 accuracy @ i pn @ t a = +85 c x 85 c % of i pn ?3.2 3.2 see formula note 1) accuracy @ i pn @ t a = +105 c x 105 c % of i pn ?3.9 3.9 see formula note 1) note : 1) accuracy @ t a (% of i pn ) = x + ( (t a ?25) + 100 ( t a ?25)). tcg 10000 tci oe 1000 i pn hlsr-p/sp33 series
page 6/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com electrical data hlsr 32-p/sp33 at t a = 25 c, u c = +3.3 v, r l = 10 k? unless otherwise noted (see min, max, typ. defnition paragraph in page 9). parameter symbol unit min typ max comment primary nominal rms current i pn a 32 primary current, measuring range i pm a -80 80 for u c = 3.3 v 5 % number of primary turns n p - 1 resistance of primary jumper @ t a = 25 c r p m? 0.21 resistance of primary jumper @ t a = 105 c r p m? 0.29 t jumper = 120 c supply voltage u c v 3.135 3.3 3.465 current consumption i c ma 19 25 reference voltage (output) v ref v 1.63 1.65 1.67 internal reference reference voltage (input) v ref v 0.5 1.7 external reference output voltage range @ i pm v out ? v ref v ?1.15 1.15 over operating temperature range v ref output resistance r ref ? 130 200 300 series v out output resistance r out ? 2 5 series capacitive loading c l nf 0 6 electrical offset voltage @ i p = 0 v oe mv ?5 5 v out ? v ref electrical offset current referred to primary i oe ma ?348 348 temperature coeffcient of v ref tcv ref ppm/k ?150 150 ?40 c 105 c temperature coeffcient of v oe tcv oe mv/k ?0.075 0.075 temperature coeffcient of i oe tci oe ma/k ?5.22 5.22 theoretical sensitivity g th mv/a 14.375 460 mv @ i pn sensitivity error g % ?0.5 0.5 factory adjustment temperature coeffcient of g tcg ppm/k ?200 200 linearity error 0 i pn l % of i pn ?0.5 0.5 linearity error 0 i pm l % of i pm ?0.8 0.8 magnetic offset current (@ 10 i pn ) referred to primary i om a ?0.25 0.25 reaction time @ 10 % of i pn t ra s 2 @ 50 a / s response time @ 90 % of i pn t r s 2.5 @ 50 a / s frequency bandwidth (?3 db) bw khz 450 output rms voltage noise spectral density 100 hz 100 khz e no v / hz 5 output voltage noise dc 10 khz dc 100 khz dc 1 mhz v no mvpp 4 10 16 accuracy @ i pn x % of i pn ?1 1 accuracy @ i pn @ t a = +85 c x 85 c % of i pn ?3.2 3.2 see formula note 1) accuracy @ i pn @ t a = +105 c x 105 c % of i pn ?3.9 3.9 see formula note 1) note : 1) accuracy @ t a (% of i pn ) = x + ( (t a ?25) + 100 ( t a ?25)). tcg 10000 tci oe 1000 i pn hlsr-p/sp33 series
page 7/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com electrical data hlsr 40-p/sp33 at t a = 25 c, u c = +3.3 v, r l = 10 k? unless otherwise noted (see min, max, typ. defnition paragraph in page 9). parameter symbol unit min typ max comment primary nominal rms current i pn a 40 primary current, measuring range i pm a ?100 100 for u c = 3.3 v 5 % number of primary turns n p - 1 resistance of primary jumper @ t a = 25 c r p m? 0.21 resistance of primary jumper @ t a = 105 c r p m? 0.29 t jumper = 120 c supply voltage u c v 3.135 3.3 3.465 current consumption i c ma 19 25 reference voltage (output) v ref v 1.63 1.65 1.67 internal reference reference voltage (input) v ref v 0.5 1.7 external reference output voltage range @ i pm v out ? v ref v ?1.15 1.15 over operating temperature range v ref output resistance r ref ? 130 200 300 series v out output resistance r out ? 2 5 series capacitive loading c l nf 0 6 electrical offset voltage @ i p = 0 v oe mv ?5 5 v out ? v ref electrical offset current referred to primary i oe ma ?435 435 temperature coeffcient of v ref tcv ref ppm/k ?150 150 ?40 c 105 c temperature coeffcient of v oe tcv oe mv/k ?0.075 0.075 temperature coeffcient of i oe tci oe ma/k ?6.52 6.52 theoretical sensitivity g th mv/a 11.5 460 mv @ i pn sensitivity error g % ?0.5 0.5 factory adjustment temperature coeffcient of g tcg ppm/k ?200 200 linearity error 0 i pn l % of i pn ?0.5 0.5 linearity error 0 i pm l % of i pm ?0.8 0.8 magnetic offset current (@ 10 i pn ) referred to primary i om a ?0.25 0.25 reaction time @ 10 % of i pn t ra s 2 @ 50 a / s response time @ 90 % of i pn t r s 2.5 @ 50 a / s frequency bandwidth (?3 db) bw khz 450 output rms voltage noise spectral density 100 hz 100 khz e no v / hz 4.5 output voltage noise dc 10 khz dc 100 khz dc 1 mhz v no mvpp 4 9 14 accuracy @ i pn x % of i pn ?1 1 accuracy @ i pn @ t a = +85 c x 85 c % of i pn ?3.2 3.2 see formula note 1) accuracy @ i pn @ t a = +105 c x 105 c % of i pn ?3.9 3.9 see formula note 1) note : 1) accuracy @ t a (% of i pn ) = x + ( (t a ?25) + 100 ( t a ?25)). tcg 10000 tci oe 1000 i pn hlsr-p/sp33 series
page 8/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com electrical data hlsr 50-p/sp33 at t a = 25 c, u c = +3.3 v, r l = 10 k? unless otherwise noted (see min, max, typ. defnition paragraph in page 9). parameter symbol unit min typ max comment primary nominal rms current i pn a 50 primary current, measuring range i pm a ?125 125 for u c = 3.3 v 5 % number of primary turns n p - 1 resistance of primary jumper @ t a = 25 c r p m? 0.21 resistance of primary jumper @ t a = 105 c r p m? 0.29 t jumper = 120 c supply voltage u c v 3.135 3.3 3.465 current consumption i c ma 19 25 reference voltage (output) v ref v 1.63 1.65 1.67 internal reference reference voltage (input) v ref v 0.5 1.7 external reference output voltage range @ i pm v out ? v ref v ?1.15 1.15 over operating temperature range v ref output resistance r ref ? 130 200 300 series v out output resistance r out ? 2 5 series capacitive loading c l nf 0 6 electrical offset voltage @ i p = 0 v oe mv ?5 5 v out ? v ref electrical offset current referred to primary i oe ma ?543 543 temperature coeffcient of v ref tcv ref ppm/k ?150 150 ?40 c 105 c temperature coeffcient of v oe tcv oe mv/k ?0.075 0.075 temperature coeffcient of i oe tci oe ma/k ?8.15 8.15 theoretical sensitivity g th mv/a 9.2 460 mv @ i pn sensitivity error g % ?0.5 0.5 factory adjustment temperature coeffcient of g tcg ppm/k ?200 200 linearity error 0 i pn l % of i pn ?0.5 0.5 linearity error 0 i pm l % of i pm ?0.8 0.8 magnetic offset current (@ 10 i pn ) referred to primary i om a ?0.25 0.25 reaction time @ 10 % of i pn t ra s 2 @ 50 a / s response time @ 90 % of i pn t r s 2.5 @ 50 a / s frequency bandwidth (?3 db) bw khz 450 output rms voltage noise spectral density 100 hz 100 khz e no v / hz 4 output voltage noise dc 10 khz dc 100 khz dc 1 mhz v no mvpp 3.3 7.3 12 accuracy @ i pn x % of i pn ?1 1 accuracy @ i pn @ t a = +85 c x 85 c % of i pn ?3.2 3.2 see formula note 1) accuracy @ i pn @ t a = +105 c x 105 c % of i pn ?3.9 3.9 see formula note 1) note : 1) accuracy @ t a (% of i pn ) = x + ( (t a ?25) + 100 ( t a ? 25)). tcg 10000 tci oe 1000 i pn hlsr-p/sp33 series
page 9/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com maximum continuous dc current important notice : whatever the usage and/or application, the transducer jumper temperature shall not go above the maximum ratings of 120 c as stated in page 2 of this datasheet. defnition of typical, minimum and maximum values minimum and maximum values for specifed limiting and safety conditions have to be understood as such as well as values shown in typical graphs. on the other hand, measured values are part of a statistical distribution that can be specifed by an interval with upper and lower limits and a probability for measured values to lie within this interval. unless otherwise stated (e.g. 100 % tested), the lem defnition for such intervals designated with min and max is that the probability for values of samples to lie in this interval is 99.73 %. for a normal (gaussian) distribution, this corresponds to an interval between ?3 sigma and +3 sigma. if typical values are not obviously mean or average values, those values are defned to delimit intervals with a probability of 68.27 %, corresponding to an interval between ?sigma and +sigma for a normal distribution. typical, minimum and maximum values are determined during the initial characterization of the product. 0 20 40 60 - 40 - 20 0 20 40 60 80 10 0 12 0 14 0 h l s r 1 0 - p/sp33 h l s r 20 - p/sp33 h l s r 32 - p/sp33 h l s r 40 - p/sp33 h l s r 50 - p/sp33 i p ( a ) t a ( c) hlsr-p/sp33 series
page 10/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com measuring range versus external reference voltage - 75 - 50 - 25 0 25 50 75 0.5 0.7 0.9 1.1 1.3 1.5 1.7 i p (a) h l sr 10- xx/ sp33 u c = 3 . 3 v u c = 3 . 14 v u c = 2 . 97 v v r e f ( v ) - 150 - 125 - 100 - 75 - 50 - 25 0 25 50 75 10 0 12 5 15 0 0.5 0.7 0.9 1.1 1.3 1.5 1.7 h l sr 50- xx/ sp33 u c = 3 . 3 v u c = 3 . 14 v u c = 2 . 97 v v r e f ( v ) i p (a ) - 150 - 125 - 100 - 75 - 50 - 25 0 25 50 75 10 0 12 5 15 0 0.5 0.7 0.9 1.1 1.3 1.5 1.7 h l sr 20- xx/ sp33 u c = 3 . 3 v u c = 3 . 14 v u c = 2 . 97 v i p (a) v r e f ( v ) - 150 - 125 - 100 - 75 - 50 - 25 0 25 50 75 10 0 12 5 15 0 0.5 0.7 0.9 1.1 1.3 1.5 1.7 h l sr 32- xx/ sp33 u c = 3 . 3 va u c = 3 . 14 v u c = 2 . 97 v i p (a) v r e f ( v ) - 150 - 125 - 100 - 75 - 50 - 25 0 25 50 75 10 0 12 5 15 0 0.5 0.7 0.9 1.1 1.3 1.5 1.7 h l sr 40- xx/ sp33 u c = 3 . 3 v u c = 3 . 14 v u c = 2 . 97 v i p (a) v r e f ( v ) hlsr-p/sp33 series
page 11/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com pcb footprint (in mm. general linear tolerance 0.2 mm) assembly on pcb recommended pcb hole diameter 1.6 mm for primary pins 1 mm for secondary pins maximum pcb thickness 2.4 mm wave soldering profle maximum 260 c for 10 s no clean process only. safety this transducer must be used in limited-energy secondary circuits according to iec 61010-1. this transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturers operating instructions. caution, risk of electrical shock when operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). ignoring this warning can lead to injury and/or cause serious damage.this transducer is a build-in device, whose conducting parts must be inaccessible after installation.a protective housing or additional shield could be used.main supply must be able to be disconnected. d c p d c i hlsr-p/sp33 series
page 12/12 7september2015/version 7 lem reserves the right to carry out modifcations on its transducers, in order to improve them, without prior notice www.lem.com dimensions (in mm. general linear tolerance 0.2 mm) remarks v out is positive with respect to v ref when positive i p fows in direction of the arrow shown on the drawing above installation of the transducer must be done unless otherwise specifed on the datasheet, according to lem transducer generic mounting rules. please refer to lem document nane120504 available on our web site: products/product documentation. connection u c v out v ref i p hlsr-p/sp33 series

▲Up To Search▲

Price & Availability of HLSR10-P-SP33

	To Download HLSR10-P-SP33 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .