www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 9 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 915 c 1 smd - 6 m arking ? hdf69 43 prepared checked a pproved ? d a t e 2010 - 6 - 1 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 9 ?? history record date spec . no . ?? part no . ??? customer no . modify content ? remark
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 9 1. package dimension 2. marking hdf 69 43 hd: brand f : filter 6 smd - 6 9 43 : no. 3. performance 3.1 application low - loss rf filter for remote control receivers center frequency:915 mhz 3.2 maximum rating operation temperature range - 4 0 to + 85 storage temperature range - 40 to +85 dc. permissive voltage 5 v dc. max. maximum input power 1 5 dbm
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 9 3.3 electronic characteristics temperature range for specification: t = ? 40 c to +85 c terminating source impedance: z s = 50 w terminating load impedance: z l = 50 w u nit minimum typical maximum center frequency mhz - 915 - insertio n loss ( 902~928 mhz) db 2. 4 3.5 amplitude ripple ( 902~928 mhz) db 0. 9 1. 8 relative attenuation 10.0 ~ 800.0 mhz 800.0~845.0mhz 845 .0 mhz ~ 8 80 .0 mhz 947 .0 mhz ~ 992 .0 mhz 992 .0 mhz ~ 1 020 .0 mhz 1 020 .0 mhz ~ 12 00.0 mhz db 50 45 33 2 5 35 45 55 50 43 3 5 4 5 50 - input/output impedance ohms 50 3.4 frequency characteristics
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 9 3.5 test circuit 4. environmental characteristics 4 - 1 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 3.3 . 4 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 9 in 3.3 . 4 - 3 solderability submerge the device termi nals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 3.3 . 4 - 4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 3.3 . 4 - 5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 3.3 . 5. remark 5.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 5.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 5.3 soldering only leads of component may be soldered. please avoid soldering another part of component. 6 . packing 6 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 6 .2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 6 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below.
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 9 (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications. 7 . tape specifications 7 .1 tensile strength of carrier tape: 4.4n/mm width 7 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 9 [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 4 .0 0.1 2.0 0.05 ? 1.5 0.1 ? 1.0 0.25 0.3 0.05 1.2 5 0.1 3.3 0.1 3.3 0.1 [figure 2]
s aw filter hdf 915 c 1 s6 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 9 of 9
|
