gamewell-fci 12 clintonville road, northford, ct 06472-1610 usa ? tel: (203) 484-7161 ? fax: (203) 484-7118 specifications are for inform ation only, are not intended for installation purpos es, and are subject to change without notice. no responsibility is assumed by gamewell-fci for their use. ?2013 by honeywell international inc. all rights reserved. www.gamewell-fci.com 9021-60497 rev. e page 1 of 2 anx addressable node expander signaling s1869 approved fdny: coa #6077 mea 7165-1703:0125 3025415 approved fm description the gamewell-fci, addressable node expander (anx) is a networking interface board th at is used to expand the overall e3 series ? capabilities in th e system node count, focalpoint ? integration and ethernet connectivity. this powerful interface provides greater data exchange between the following units. ? e3 series facp ? focalpoint graphical workstation ? s3 series facp ? installer?s pc the anx allows the e3 series and s3 series networks to expand to two rings. each ring contains up to 61 nodes, not including the anx. by bridging the two networks together, each of the e3 and s3 network node counts are increased to 122 nodes. the multi-ring network expansion can activate outputs on any node on the bridged networks including the control-by-event functions originating from a connected network (see figur e 1-shared ring capability). audio paging and voice messages are also transferred over the two networks through the anx. the use of the anx?s ethernet port allows the communica- tion between the e3 series system, the focalpoint gate- ways and workstations thr ough the tcp/ip. from the focalpoint workstation, you can activate ?virtual switches? in the anx for cam control and status monitoring which might include bypass, control switching, voice evacuation notification or any auxiliary control function. installers can use the anx?s ethernet port for high-speed configuration downloading into either of the e3 series or s3 series rings, saving time over using the typical rs-232 connections. the anx can also be used as a downloading gateway for commissioning and is not required to be a part of the system. the anx expands the operation of the e3 network so that it can support both mass notification and emergency com- munication system applications used in campuses, large industrial or manufacturing facilities, hospitals, high-rise and multi-building complexes. the following three types of anx sub-assemblies provide ethernet connectivity via an ethernet port. ? addressable node expander - single ring (anx-sr). - contains a single e3 series local network connection. ? addressable node expander - multi-ring twisted-pair (anx-mr-utp) contains the following: - a primary and secondary network interface for multi- ring communication. - includes twisted-pair copper (utp) on the secondary network connection. ? addressable node expander - multi-ring fiber optic (ANX-MR-FO) contains the following: - primary network inte rface for multi-ring communication. - a fiber-optic (fo) connectivity on the secondary network connection. features ? complies with ul ? standard 864 (9th edition). ? expands the e3 and s3 networks to two rings, contain- ing 122 nodes allowing a multi-ring network expansion. ? provides expanded data exchanges between the e3 network and the focalpoint graphic workstation. ? includes high-speed configuration downloading through the anx ethernet port. ? installed in the standard e3 series cabinet enclosures. ? bridges two of either the e3 series or s3 series net- works to activate outputs on any node on bridged net- works. ? offers shared ring capability. focalpoint features ? displays device descriptions for points on events only. ? shows a single icon per slc device. ? provides up to 512 virtual points for programmable control and status monitoring within focalpoint for: - system control switch (enable/disable, bypass). - voice evacuation speaker circuit control switch. - auxiliary control circuit switch. ? provides ethernet connectivity to allow a high speed supervised connection to the focalpoint gateway. ? includes additional point information to the end user. ? allows the user to send the following commands over the e3 network. - acknowledge - reset - silence - enable/disable ? shows the current status on the e3 and s3 networks. ? sends the time to the e3 and s3 networks. anx
gamewell-fci 12 clintonville road, northford, ct 06472-1610 us a ? tel: (203) 484-7161 ? fax: (203) 484-7118 9021-60497 rev. e page 2 of 2 www.gamewell-fci.com ethernet the addressable node expander uses tcp/ip and incor- porates heavy ppl/psl/ re-use of the mainstream compo- nents. the three types of anx sub-assemblies can provide ethernet connectivity via an ethernet port. this ethernet port offers an enhanced network interface between the e3 series and s3 series fire alarm control panel and the focalpoint gra phic workstation. this fea- ture improves the communication to monitor the alarm supervisory and trouble conditions of the focalpoint graphic workstation. the e3 series configuration data can be loaded into the netwo rk nodes via the anx ether- net port and camworks?. a download program utility is provided to extract data (excluding the cams and voice files on the ini-vg series) into a job file that allows the anx to extract all point infor- mation in existing panels. the following list the information that can be retrieved from the anx. ? custom labels programmed to identify each point. ? system information that de tails the configuration of analog addressable monitor and control points ? information stored in the camworks job file ? compare feature to display configuration differences ? converts low level cams into corresponding high level cams during the download of the camworks configu- ration data for the following node types: - ili-mb-e3 - ili-s-e3 - ili95-mb-e3 - ili95-s-e3 - nga - anx - slp-e3 e3 series ? and focalpoint ? are registered trademarks of honeywell international inc. camworks? is a trademark of honeywell international inc ul ? is a registered trademark of underwriters laboratories inc. specifications operating voltage: 24 vdc (from the pm-9/pm-9g power supply) operating/supervisory current: 0.066 amp alarm current: 0.066 amp operating temperature: 32 to 120 f (0 to 49 c) relative humidity: 0 to 93%, non-condensing at 90 f (32 c) supervised wiring specifications: (anx-mr-utp & ANX-MR-FO only): copper wire: 16 to 18 awg twisted-pair, unshielded. up to 3,000 feet (914.4 m) between each node. fiber-optic cable (ANX-MR-FO only): up to 200 microns (optimized for 62.5/125 microns). up to 8 db loss between each node. ordering information part number description anx-sr addressable node expander-single ring anx-mr-utp addressable node expander-multi-ring twisted-pair ANX-MR-FO addressable node expander-multi-ring fiber optic figure 1: addressable node expa nder connection in a multi-ring network expansion configuration
|
