zettler electronics gmbh junkersstr. 3, d-82178 puchheim, germany phone: +49 89 800 97-0 fax: +49 89 800 97-200 office@zettlerelectronics.com www.zettlerelectronics.com this product specification to be used only together with the application notes which can be downloaded from http://www.zettlerelectronics.com/pdfs/relais/applicationnotes.pdf az762p 20 amp latching power relay features ? dielectric strength 4000 vrms ? low height: 16 mm ? 20 amp switching ? ul, cur file e44211 notes 1. all values at 20c (68f). 2. relay may pull in with less than ?set/reset? value. 3. specifications subject to change without notice. 4. initial state of contacts may be changed during transportation or shock! contacts coil life expectancy mechanical electrical minimum operations 1 x 10 6 1 x 10 5 set time (typical) 10 ms at nominal coil voltage reset time (typical) 10 ms at nominal coil voltage min. pulse time 75 ms max. pulse time 1 min. dielectric strength (at sea level for 1 min.) 4000 vrms coil to contact 1000 vrms between open contacts insulation resistance 1000 megaohms min. at 20c 500 vdc 50% rh insulation (according to din vde 0110, iec 60664-1) c250 overvoltage category: iii pollution degree: 3 nominal voltage: 250 vac ambient temperature operating at nominal coil voltage -40c (-40f) to 85c (185f) vibration 0.062? (1.5 mm) da at 10-55 hz shock 10 g enclosure p.b.t. polyester terminals tinned copper alloy, p.c. max. solder temp. 270c (518f) max. solder time 5 seconds max. solvent temp. 80c (176f) max. immersion time 30 seconds weight 13 grams packing unit in pcs. 50 per tray / 500 per carton box power at set/reset voltage (typical) 256 mw (single coil) 384 mw (dual coil) 416 mw (dual coil 24 v) temperature max. 155c (311f) class f arrangement spdt (1 form c) spst (1 form a) ratings resistive load: max. switched power: 5000 va max. switched current: 20 a max. inrush current ?1at? version: 165 a , 20 ms 500 a, 2 ms 800 a, 200 s max. switched voltage: 125vdc* or 350 vac * note: if switching voltage is greater than 30 vdc, special precautions must be taken. please contact the factory. rated load ul, cur 1 form a 20 a at 250 vac, resistive, 20k cycles, 70c [1] 16 a at 250 vac, resistive, 100k cycles, 85c [1] 6 a at 277 vac, tungsten, 6k cycles, 40c [1] 6 a at 277 vac, standard ballast, 6k cycles, 40c [1] 1.5 hp at 250 vac, 40c [1] 3300 w at 277 vac, electronic ballast, 20k cycles, 40c [2] 3000 w at 220 vac, tungsten, 6k cycles, 40c [2] 1500 w at 347 vac, standard ballast, 20k cycles, 40c [2] 1 form c (normally open) 20 a at 250 vac, resistive, 20k cycles, 70c [1] 16 a at 250 vac, resistive, 100k cycles, 85c [1] 1 form c (normally closed) 16 a at 250 vac, resistive, 50k cycles, 85c [1] material silver tin oxide [1], silver tin oxide + tungsten [2] resistance < 20 milliohms initially general data 2013-07-18
zettler electronics gmbh junkersstr. 3, d-82178 puchheim, germany phone: +49 89 800 97-0 fax: +49 89 800 97-200 office@zettlerelectronics.com www.zettlerelectronics.com this product specification to be used only together with the application notes which can be downloaded from http://www.zettlerelectronics.com/pdfs/relais/applicationnotes.pdf az762p single coil latching coil specification order number* nominal coil vdc set/reset vdc max. continuous vdc coil resistance ohm 10% 1 form a 1 form c 3 2.4 3.9 22.5 az762p1-1ae-3d az762p1-1ce-3d 5 4.0 6.5 62.5 az762p1-1ae-5d az762p1-1ce-5d 6 4.8 7.8 90 az762p1-1ae-6d az762p1-1ce-6d 9 7.2 11.7 202 az762p1-1ae-9d az762p1-1ce-9d 12 9.6 15.6 360 az762p1-1ae-12d az762p1-1ce-12d 24 19.2 31.2 1,440 az762p1-1ae-24d AZ762P1-1CE-24D * ?1ae? or ?1ce? denote silver tin oxide contacts. substitute ?1at? in place of ?1ae? for silver tin oxide contacts with tungsten premake contact. add suffix ?e? at the end of the order number for sealed version. add suffix ?k? at the end of the order number for 3.5 mm pin spacing version. (not available for ?1at? version) add suffix ?r? at the end of the order number for reversed polarity coil. 2013-07-18 relay ordering data dual coil latching coil specification order number* nominal coil vdc set/reset vdc max. continuous vdc coil resistance ohm 10% 1 form a 1 form c 3 2.4 3.9 15 az762p2-1ae-3d az762p2-1ce-3d 5 4.0 6.5 42 az762p2-1ae-5d az762p2-1ce-5d 6 4.8 7.8 60 az762p2-1ae-6d az762p2-1ce-6d 9 7.2 11.7 135 az762p2-1ae-9d az762p2-1ce-9d 12 9.6 15.6 240 az762p2-1ae-12d az762p2-1ce-12d 24 19.2 31.2 886 az762p2-1ae-24d az762p2-1ce-24d wiring diagram contact positions are shown in energized coil state. single coil latching 4 6 3 viewed toward terminals 4 3 2(-) 1(+) 4 3 2(+) 1(-) 2(-) 1(+) 6 4 3 2(+) 1(-) single coil latching 1 form c dual coil latching 4 6 3 1 form a 4 3 5(+) 1(-) 4 3 2(-) 5(+) 6 4 3 dual coil latching 5(+) 1(-) 2(-) 5(+) 4 6 3 4 3 2(+) 1(-) 4 3 2(-) 1(+) 2(+) 1(-) 6 4 3 2(-) 1(+) 4 6 3 4 3 5(-) 1(+) 4 3 2(+) 5(-) 6 4 3 5(-) 1(+) 2(+) 5(-) standard polarity reversed polarity set reset set reset set reset set reset set reset set reset set reset set reset
zettler electronics gmbh junkersstr. 3, d-82178 puchheim, germany phone: +49 89 800 97-0 fax: +49 89 800 97-200 office@zettlerelectronics.com www.zettlerelectronics.com this product specification to be used only together with the application notes which can be downloaded from http://www.zettlerelectronics.com/pdfs/relais/applicationnotes.pdf 2013-07-18 az762p mechanical data 2.15 pc board layout 20.3 3 x ? 1.5 7.5 * not used on single coil version viewed toward terminals 5 5 1.55 2.75 * not used on 1 form a version 2.15 20.3 3.5 0.1 3.5 0.3 3 x 1 0.04 3 x ? 1.5 20.3 0.3 12.7 0.3 7.5 7.5 0.1 29.4 0.4 terminal not used on single coil version 15.7 0.3 * not used on single coil version viewed toward terminals 3.5 0.1 3 x 0.5 0.04 3 x 0.5 0.04 3 x 0.5 0.04 3.5 3.5 2.75 * 5.0 mm spacing - standard version 3.5 mm spacing - "k" version 0.3 0.2 5 0.1 3.5 0.3 3 x 1 0.04 20.3 0.3 12.7 0.3 7.5 0.1 29.4 0.4 terminal not used on single coil version 15.7 0.3 5 0.1 3 x 0.5 0.04 3 x 0.5 0.04 3 x 0.5 0.04 0.3 0.2 3.05 3 x ? 1.0 not used on 1 form a version 3 x ? 1.0 * terminal not used on 1 form a version * * terminal not used on 1 form a version *
|
