spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 1 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 3.5x2.8mm surface mount led lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: AAAF3529LSEKJ3ZGKQBS hyper red green blue descriptions z the hyper red device is bas ed on light emitting diode chip made from algainp. z the green source color devices are made with ingan on sapphire light emitting diode. z the blue source color devices are made with ingan on sapphire light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications. features z outstanding material efficiency. z low power consumption. z can produce any color in visible spectrum, including white light. z suitable for all smd assembly and solder process. z available on tape and reel. z package: 2000pcs / reel . z moisture sensitivity level : level 3. z rohs compliant. blue green red
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 2 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 handling precautions compare to epoxy encapsulant that is hard and brittle, si licone is softer and flexible. although its characteristic significantly orangeuces thermal stress, it is more susceptible to damage by external mechanical force. as a result, special handling precau tions need to be observed during asse mbly using silicone encapsulated led products. failure to comply might lead to damage and premature failure of the led. 1. handle the component along the side surfaces by using forceps or appropriate tools. 2. do not directly touch or handle the silicone lens surface. it may damage the internal circuitry. 3. do not stack together assembled pcbs containing ex posed leds. impact may scratch the silicone lens or damage the internal circuitry. 4.1. the inner diameter of the smd pickup nozzle should not exceed the size of the led to prevent air leaks. 4.2. a pliable material is suggested fo r the nozzle tip to avoid scratching or damaging the led surface during pickup. 4.3. the dimensions of the component must be accurately program med in the pick-and-place machine to insure precise pickup and avoid damage during production. 5. as silicone encapsulation is permeable to gases, some corro sive substances such as h 2 s might corrode silver plating of leadframe. special care should be taken if an led with silicone encapsulation is to be used near such substances.
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 3 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. 3. luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (mcd) [2] @ 2ma v iewing angle [1] min. typ. 2 1/2 AAAF3529LSEKJ3ZGKQBS hyper red (algainp) water clear 30 60 green (ingan) 80 180 blue (ingan) 12 30 120 symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper red green blue 640 515 460 nm i f =2ma d [1] dominant wavelength hyper red green blue 625 525 465 nm i f =2ma ? 1/2 spectral line half-width hyper red green blue 20 35 25 nm i f =2ma c capacitance hyper red green blue 27 45 100 pf v f =0v;f=1mhz v f [2] forward voltage hyper red green blue 1.8 2.65 2.65 2.1 3.1 3.1 v i f =2ma i r reverse current hyper red green blue 10 50 50 ua v r =5v parameter hyper red green blue units power dissipation 105 93 93 mw dc forward current 50 30 30 ma peak forward current [1] 150 150 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c electrostatic dischar ge threshold (hbm) 3000 v 450 250
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 4 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 AAAF3529LSEKJ3ZGKQBS hyper red
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 5 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 green
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 6 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 blue
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 7 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 AAAF3529LSEKJ3ZGKQBS reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao5236 rev no: v.1b date: sep/18/2015 page: 8 of 8 approved: wynec checked: allen liu drawn: m.liu erp: 1201009105 packing & label specifications AAAF3529LSEKJ3ZGKQBS terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
