model output voltage maximum output current sip 90 C 0.1w <25 C 90v 0 to 1 ma sip 100 C 1w <25 C 100v 0 to 10 ma page 1 90v @ 0.1w and 100v @ 1w product description proven reliability sip series regulated, low ripple high voltage dc to dc converters block diagram product description product selection table features applications ? low ripple ? well regulated ? analog programming voltage ? ultra-thin, 0.16 inches (4mm) ? high performance low cost ? mtbf: >2.03 million hours per bellcore tr-332 ? packaging: epoxy coated ? rohs compliant ? photomultiplier tubes ? mass spectrometers ? avalanche photodiode ? microchannel plates ? piezo materials ? igniters ? capacitor charging ideal for apd biasing and mems driver applications, the sip series provides high performance in an ultra-thin, miniature single in-line package. designed for low cost, high quantity applications, these dc to dc converters deliver high stability with very low ripple. the output voltage is programmable via a 0 to 5 volt analog voltage. the output voltage is inversely related to the programming voltage, i.e. applying 5 volts to the programming sets the output voltage to the minimum level. conversely, 0 volts on the programming sets the output voltage to the maximum level. the supply is linearly program - mable through this range*2. an enable/disable function is included. applying a ttl low (open collector compatible) disables the output voltage to less than 10 volts. 4760w02 www.xppower.com
model sip90 SIP100 output voltage <25 to 90vdc <25 to 100vdc max output current *1 0 to 1ma 0 to 10ma ripple p-p <5mv <10mv input voltage 3 to 6.7vdc 4 to 6.7vdc input current [no load] <125ma <75ma input current [full load] <150ma <350ma line regulation 0.05% 0.20% load regulation 0.03% 0.10% programming voltage see below programming accuracy 91 +/-1 frequency 2mhz +/- 5% stability < 0.01%/hr [1hr warm up] tempco <100ppm / deg c operating temperature -20 to +70c *3 (case) storage temperature -20 to +105c ou tp ut vo lt ag e (p in 4) vs. pr ogra mmin g vo lt ag e ( pin 1) 20 30 40 50 60 70 80 90 10 0 00 .5 11 .5 22 .5 33 .5 44 .5 programming voltage %v ou t page 2 sip series electrical specifications *2 (25 to 100vdc) voltage programming ripple measurements: 1. ripple specifed at maximum output power 2. set scope bandwidth limit to 20mhz programming pin (#1): 1. pin should be left open for min vout. 2. pin must be grounded for max vout. 3. pin can be modeled in the following way: (please refer to the programming voltage chart) sip90 programming voltage = SIP100 programming voltage = 91 - vout 14.1 100 - vout 15.8 4760w02 www.xppower.com
.95 (24.13 ) 1.15 (29.2) 5 .5 5 (13.97) .010 (.25 ) 5x .06 .05 (1.521.27 ) .16.0 5 (4.06) .30 (7.62) .20 (5.08) .10 (2.54) .020 (0.51) 5x 4 32 .10 (2.54) 1 modelm fg. code high voltage corporation www.emcohighvoltage.co m sip9 0 .20 (5.08) .7 5 (19.05 ) .2 0 (5.08) 1 2 3 4 5 1.20 (30.48 ) .020 (0.51) 5x .10 (2.54) .20 (5.08) .30 (7.62) 1.45 (36.8) .06 .0 5 (1.52 1.27 ) .12 (3.05) 5x .010 (.25 ) .1 6 .0 5 (4.06) modelm fg. code high voltage corporation www.emcohighvoltage.co m SIP100 dimensions are in inches (metric equivalents are in parenthesis) dimensional tolerances: .xx = + - 0.03 (0.76) pae 3 mechanical specifications sip pin # function 1 programming input 2 ground 3 disable: ttl, low, open collector compatible 4 supply voltage 5 output voltage parameter value sip 90 sip 100 weight <0.2 oz (5 grams) <0.25 oz (7.1 grams) volume 0.101 cubic inches (1,656 cubic millimeters) 0.174 cubic inches (2,850 cubic millimeters) dimensions 1.15 x 0.55 x 0.16 (29.2 x 13.97 x 4.06) 1.45 x 0.75 x 0.16 (36.83 x 19.05 x 4.06) SIP100 sip90 sip series 4760w02 www.xppower.com
page 4 application notes sip series *notes: 1. at maximum rated output voltage. 2. specifcations after 1 hour warm-up, full load, at 25c unless otherwise indicated. 3. proper thermal management techniques are required to maintain safe case temperature at maximum power output. xp emco reserves the right to make changes on products and literature, including specifcations, without notice. xp emco standard product models are not recommended for copy-exact applications or any other application restricting product changes. copy-exact options are available. please contact an xp emco sales representative for more details. 4760w02 www.xppower.com
|
