unisonic technologies co., ltd uchq200 preliminary cmos ic www.unisonic.com.tw 1 of 6 copyright ? 2016 unisonic technologies co., ltd qw-r121-029.a usb dedicated charging port controller with qc 2.0 fast charging function ? description the utc uchq200 is a fast charge protocol controller and follows quick charge 2.0 specification for smart power bank application. the protoc ol feature monitors usb d+/d- data line voltage, and automatically adjust s output voltage of power bank and wall adaptor to optimize charge time. utc uchq200 is a high performance solution for fast-charging mechanism and it saves charging time. it supports the full output voltage range of either class a or class b. optionally class b can be inhibited for protecting the battery charger from accidental damage. utc uchq200 can support not only usb bc compliant devices, but also apple / samsung devices and automatically detects whether a connected powered device (pd) is quick charge 2.0 capable before enabling output voltage adjustment. if a pd not compliant to quick charge 2.0 is detected the uchq200 disables output voltage adjustment to ensure safe operation with legacy 5v only usb p d s. ? features sop-8 * fully supports quick charge 2.0 specification: class a: 5v, 9v, 12v output voltage. class b: 5v, 9v, 12v, 20v output voltage. * supports usb dcp shorting d+ line to d- line per usb battery charging specification, revision 1.2. * meets chinese telecommunication industrial standard yd/t 1591-2009. * supports usb dcp applying 2.7v on d+ line and 2.7v on d- line. * supports usb dcp applying 1.2v on d+ and d- lines. * automatic selection of d+/d- mode for an attached device. *compliant with apple and samsung devices. ? ordering information ordering number package packing UCHQ200G-S08-R sop-8 tape reel
uchq200 preliminary cmos ic unisonic technologies co., ltd 2 of 6 www.unisonic.com.tw qw-r121-029.a ? marking information package voltage code marking sop-8 05: 5.0v 09: 9.0v 12: 12v 20: 20v ? pin configuration 7 6 5 4 3 2 1 gnd vsen1 vsen2 v dd 8 v ref vsen3 d- d+ ? pin discription pin no pin name description 1 gnd ground pin. 2 vsen1 open drain output of output voltage adjustment switch. active for 9v, 12v, 20v output setting. 3 vsen2 open drain output of output voltage adjustment switch. active for 12v, 20v output setting. 4 vsen3 open drain output of out put voltage adjustment switch. active for 20v output setting. 5 d- usb d- data line input 6 d+ usb d+ data line input 7 v ref internal reference voltage output pi n. it must be with a resistor to gnd 8 v dd power supply input pin.
uchq200 preliminary cmos ic unisonic technologies co., ltd 3 of 6 www.unisonic.com.tw qw-r121-029.a ? block diagram ? output voltage lookup table internal switch setting d+ d- output voltage sw1 sw2 sw3 3.3v 3.3v 20v 0 0 0 0.6v 0.6v 12v 0 0 1 3.3v 0.6v 9v 0 1 1 0.6v gnd 5v(default) 1 1 1 note: 1 represent the nmos are o ff, 0 represent the nmos are on.
uchq200 preliminary cmos ic unisonic technologies co., ltd 4 of 6 www.unisonic.com.tw qw-r121-029.a ? absolute maximum rating parameter symbol ratings unit input supply voltage v dd -0.3 ~ +8.0 v all other pins voltage -0.3 ~ +8.0 v storage temperature t s -65 ~ + 150 c note: absolute maximum ratings are those values beyo nd which the device could be permanently damaged. ? recommended operating conditions parameter symbol test conditions min typ max unit input supply voltage v dd operating 4.0 6.0 v operating temperature range t opr -40 +85 c ? electrical characteristics (v dd =5v, t a =25c, unless otherwise specified) parameter symbol test conditions min typ max unit input voltage range v dd 4 6 v input uvlo threshold v uvlo(vth) v dd rising 2.0 4.2 v v dd supply current v dd =5v,measure v dd , sw1=sw2=sw3=off 600 ua v dd shunt voltage v dd(shunt) iv dd =3ma 6.4 v reference voltage output v r 1.18 1.23 1.28 v high voltage dedicated charging port (hvdcp) data detect voltage v dat(ref) 0.25 0.325 0.4 v d+ high glitch filter time t glitch(bc)-d+_h 1000 1250 1500 ms output voltage glitch filter time t glitch(v)change 20 40 60 ms d- pull-down resistance r d-(dwn) 20 k ? switch sw1 on-resistance r ds_on_n1 sw1=200ua 300 ? switch sw2 on-resistance r ds_on_n2 sw2=200ua 300 ? switch sw3 on-resistance r ds_on_n3 sw3=200ua 300 ? switch sw5 on-resistance r ds_on_n5 sw5=200ua 40 ? dcp 1.2v charging mode d +_1.2v /d -_1.2v line output voltage 1.08 1.2 1.32 v d +_1.2v /d -_1.2v line output impedance 100 k ? apple 2.4a mode d +_2.7v /d -_2.7v line output voltage 2.57 2.7 2.84 v d +_2.7v /d -_2.7v line output impedance 33.6 k ?
uchq200 preliminary cmos ic unisonic technologies co., ltd 5 of 6 www.unisonic.com.tw qw-r121-029.a ? application information function description the utc uchq200 is a usb dedicated charging port controlle r can fast charge most of the handheld devices. it can be like the original charging adapter. the uchq200 can support bc1.2, apple divider mode, samsung device. the utc uchq200 is a low cost usb high voltage dedicated char ging port interface ic for quick charge 2.0 specification. it also supports full output volta ge range of quick charge 2.0 class a or class b. quick charge 2.0 interface power up d+/d- is supply 2.7v to apple device and then su pply d+ short to d- into bc1.2. set the output voltage level 5v. if d+ continuous above 0.325v and keep 1.25 seconds uchq200 into quick charge 2.0 operation mode. the output voltage (12v) can be inhibited by connect vsen2 to v dd . the output voltage (20v) can be inhibited by connect vsen3 to v dd . if p d without qc 2.0 the device will keep output voltage level 5v guarantee safe operation for only 5v usb pd. shunt regulator the wide power supply output voltage th rough external resistor from rv dd to vin. the internal with zener-diode clamp v in pin at 6.4v. rv dd =2.2k ? and cv dd =1uf. r ref =127 k ? .
uchq200 preliminary cmos ic unisonic technologies co., ltd 6 of 6 www.unisonic.com.tw qw-r121-029.a ? application circuit r sen1 r sen2 r sen3 r vdd 2.2k ? c vdd 1uf gnd vsen1 vsen2 vsen3 v dd vref d+ d- v out r ref 127k ? usb utc assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all utc products described or contained herein. utc products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
|
