gamewell-fci 12 clintonville road, northford, ct 06472-1653 us a ? tel: (203) 484-7161 ? fax: (203) 484-7118 specifications are for information only, are not intended for in stallation purposes, and are s ubject to change without notice. no responsibility is assumed by gamewell-fci for their use. ?2013 by honeywell international inc. all rights reserved. www.gamewell-fci.com 9020-0617 rev. j page 1 of 2 velociti ? series asd-pl2f, ASD-PTL2F and asd-pl2fr analog, addressable photoelectronic smoke sensor approved fm 3023594 signaling 7272-1703:0121 s1913 mea approved fdny coa #:219-02-e vol.vi description the gamewell-fci velociti ? series, analog address- able plug-in smoke sensors with integral communica- tion provide features that surpass conventional sensors. sensitivity can be programmed in the con- trol panel software, and is continuously monitored and reported to the panel. point id capability allows each sensor?s address to be set, providing exact locations for selective maintenance when the cham- ber contamination reaches an unacceptable level. the asd-pl2f photoelectric sensor?s unique optical sensing chamber is engineered to sense smoke pro- duced by a wide range of combustion sources. dual electronic thermistors add 135f (57c) fixed-tem- perature thermal sensing on the ASD-PTL2F model. the velociti ? series use a communication protocol that substantially increases the speed of communica- tion between the sensors and certain gamewell-fci analog addressable fire alarm controls. these devices operate in a grouped fashion. if one of the devices in the group has a status change, the panel?s microprocessor stops the group poll and concen- trates on the single device. the net effect is a response speed up to five times greater than earlier designs. velociti ? is a registered trademark of honeywell international inc. ul ? is a registered trademark of underwriters laboratories inc. ordering information part number description asd-pl2f analog, addressable photoelectronic smoke sensor ASD-PTL2F analog, addressabl e photoelectronic smoke sensor with thermal sensing asd-pl2fr analog, addressable photoelectronic smoke sensor used with the dnr duct base when the remote test is required. features ? sleek, low-profile design. ? visual rotary, decimal switch addressing (01-159). ? built-in functional test switch activated by an external magnet. ? bicolor leds flash green whenever the sensor is addressed, and light steady red on alarm.* ? optional relay, isolator, or sounder bases. ? low standby current. ? analog addressable communication. ? stable communication technique with noise immunity. ? optional remote, single-gang led indicator (ra100z). ? compatible with gamewell-fci analog addressable panels. note: *only the red led is operative in panels that do not operate in velociti ? mode. asd-pl2fr asd-pl2f/ASD-PTL2F
gamewell-fci 12 clintonville road, northford, ct 06472-1653 us a ? tel: (203) 484-7161 ? fax: (203) 484-7118 9020-0617 rev. j page 2 of 2 www.gamewell-fci.com installation asd-pl2f plug-in sensors use a separate base to simplify installation, serv ice, and maintenance. a special tool allows maintenance personnel to plug-in and remove sensors without using a ladder. mount the base on a box which is at least 1.5" (3.8 cm) deep. suitable mounting base boxes include: ?4.0" (10.2 cm) square box. ?3.5" (8.9 cm) or 4.0" (10.2 cm) octagonal box. ? single-gang box (except relay or isolator bases). ? with b200s or b200sr base, mounted on a 4.0" (10.2 cm) octagonal or square box. ? with b224rb or b224bi base, mounted on a 3.5" (8.9 cm) octagonal box, or a 4.0" (10.2 cm) octagonal or square box. note: because of the inhere nt supervision provided by the slc, end-of-line resistors are not required. wiring ?t-taps? or branches are permitted for style 4 (class ?b?) wiring. sensor spacing gamewell-fci recommends that the spacing sensors be used in compliance with nfpa 72. specifications asd-pl2f, ASD-PTL2F, asd-pl2fr: dimensions: 2.1? (5.1 cm) height diameter: 4.1? (10.4 cm) installed in the b501 base 6.1? (15.5 cm) installed in the b210lp base shipping weight: 5.2 oz. (147 g) operating temperature: asd-pl2f: 32 f to 120 f (0 c to 49 c) ASD-PTL2F: 32 f to 100 f (0 c to 38 c) ul ? -listed velocity range: 0-4000 ft./min. (1 ,219.2 m/min.), suitable for installation in ducts. relative humidity: 10-93% (non-condensing) thermal ratings: fixed-temperature setpoint 135 f (57 c) electrical specifications voltage range: 15 ? 32 volts dc peak standby current: (max. avg.): .0003 a @ 24 vdc (one communication every 5 seconds with led blink enabled). maximum alarm- current: .0065 a @ 24 vdc (led) lit). bases and options b501 plug-in sensor base without flange dimensions: 4.1? (10.4 cm) diameter b210lp flanged mounting base dimensions: 6.1? (15.5 cm) diameter b210lpbp flanged mounting base bulk pack dimensions: 6.1? (15.5 cm) diameter b224rb relay base plug-in sensor base with auxiliary relay, spdt, rated 2 amps @ 30 vdc (resistive). screw terminals: up to 14 awg (2.0 mm 2 ) 2 coil latching relay 1 form c contact ul/csa rating: 0.9 a @ 125 vac, inductive 0.9 a @ 110 vdc, inductive 3 a @ 30 vdc, resistive dimensions: 6.1? (15.5 cm) diameter maximum: 25 devices between isolator bases. b200s intelligent sensor sounder base dimensions: 6.875? (17.5 cm) diameter b200sr standard sounder base, ul 8649th edition compliant, ulc listed dimensions: 6.875? (17.5 cm) diameter ra100z remote led annunciator bck-200 black detector covers (box of 10) dnr duct smoke housing
|
