NSVS1120 apr. 2013 application 570mhz wlan if electrical specification: (table 1) the device characteristics are measured in the circuit shown in fig.1. (operating temperature range : -20~+60oc) maximum rating: (table 2) mechanical specifications: (fig.2) package is designed as small as 3.0x3.0x1.15[mm 3 ] for smd (surface mount device) type. notice: this part is electrostatic discharge sensitive and may be damaged by improper handling. table 1. electrical specifications item spec. typ. input and output impedance - 50 nominal center frequency (f0) - 570mhz insertion loss 561.5~578.5mhz 4.7db max. 3.8db response variation 561.5~578.5mhz 2.5db max. 1.7db input and output vswr 561.5~578.5mhz 3.0 max. 2.5 group delay ripple 561.5~578.5mhz 50nsec max. 20nsec 370~548mhz 30db min. 37db 553mhz 7db min. 10db 555mhz 5db min. 7db 585mhz 5db min. 7db 587mhz 7db min. 10db out of band rejection (relative to through level) 592~770mhz 30db min. 35db table2. maximum ratings item rating maximum input power +10dbm maximum dc voltage 7.5v operating temperature range -20~+60oc storage temperature -30~+80oc newjrc saw filter NSVS1120 http://www.njr.co.jp/products/device/index.html (japanese) http://www.njr.com/products/device/index.html (english)
NSVS1120 apr. 2013 marking (1) lot number (a) year (b) month *oct.--- x nov.--- y dec.--- z (c) date *1-9--- 0 10-19--- 1 20-31--- 2 (2) part number mark pin no. connection 1 gnd 2 in/out 3 gnd 4 gnd 5 out/in 6 gnd (0.6) (0.25) (0.6) (0.53) (0.75) (0.45) 1 2 3 4 6 1. 150. 15 3. 0 0. 1 5 3. 0 0. 1 5 (a) (1) (b) (2) (1.80) 5 [2x] [4x] [4x] (c) fig.1 measuring circuit fig.2 package dimensions (in mm) fig.3 desirable land area (in mm) 221 mb in 50 out 50 0.93 0.6 0.93 3.8 3.8 2.2 1.15 1.15 sa w 3 1 2 6 4 5 15nh 20pf 20pf 15nh
NSVS1120 apr. 2013 notice 1. use this component within operating temperature range. it might not be satisfied with electrical specification without operating temperature range. when it is used less than -20oc or more than +60oc, it might be a cause of degradation or destruction of the component. even if it endures during a short time, it causes degradation of qualification. 2. when soldering iron is used, solder with the temperature at the tip of soldering iron: 350oc max., the time of soldering: 10 seconds max., the power of soldering iron: 30w max.. 3. notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. as rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. confirm that there are not any influence for qualification to this component in mounting on pcb when this component is cleaned. 6. as it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. and do not transport this component with bare hand. 7. as it might be a cause of degradation or destruction to apply d.c. voltage between each terminal, apply d.c. voltage 7.5v max. in actual circuit. note 1. this specification specifies the quality of this component as a single unit. make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. the information contained herein may be changed without prior notice. it is therefore advisable to contact new japan radio company before proceeding with the design of equipment incorporating this product. 3. the products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). new japan radio company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). when intending to use any our product please contact our sales representatives in advance.
0 10 20 30 40 50 s21 insertion loss [db] 0 2 4 6 8 10 ch1 : center 570 span 200 ch2 : center 570 span 200 insertion loss [db] frequency characteristics NSVS1120 apr. 2013 s11 s22 s11 s22 1 1 3 3 5 5 7 7 9 9 11 11 470 470 670 670 frequency [mhz] frequency [mhz] vswr vswr groupdelay [nsec] 0 50 100 150 200 250 470 570 670
|
