technical data sheet calibration adaptor rpc-2.92 jack C mini-smp jack 02K118-K20D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 1 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg all dimensions are in mm; tolerances according to i so 2768 m-h interface rpc-2.92 side according to iec 61169-35 mechanically compatible with rpc-3.50 and sma mini-smp side according to mil-std-348 mechanically compatible with gppo tm (gilbert engineering co., inc.) and ssmp tm (connectors devices, inc.) documents application note an001 calibration services material and plating connector parts material plating center conductor cube gold, min. 1.27 m, over nick el outer conductor rpc-2.92 stainless steel passivated outer conductor mini-smp cube gold, min. 1.27 m, o ver nickel dielectric ps
technical data sheet calibration adaptor rpc-2.92 jack C mini-smp jack 02K118-K20D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 2 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg electrical data frequency dc to 40 ghz return loss 3 28 db, dc to 18 ghz 3 20 db, 18 ghz to 40 ghz mechanical data rpc-2.92 mini-smp mating cycles 3 500 3 100 if mating part is full detent 3 500 if mating part is smooth bore maximum torque 1.70 nm recommended torque 0.90 nm engagement force full detent 19 n typical smooth bore 11 n typical disengagement force full detent 29 n typical smooth bore 11 n typical gauge 0.00 mm to 0.08 mm 0.00 mm to 0.08 mm general standard definition for proper operation the vector network analyzer (v na) needs a model describing the electrical behavio ur of this calibration standard. the different models, units, and terms used will depend on the vna type and they will have to be entered into the vna. all values ar e based on typical geometry and plating. offset z o / impedance / z o 50 w offset delay 46.1423 ps length (electrical) / offset length 13.83 mm offset loss 3.70 g ? /s loss 0.0148 db/ ghz environmental data operating temperature range 1 + 20 c to +26 c rated temperature range of use 2 0 c to +50 c storage temperature range - 40 c to +85 c rohs compliant 1 temperature range over which these specification ar e valid. 2 this range is underneath and above the operating te mperature range, within the calibration adaptor is fully functional and could be used without damage.
technical data sheet calibration adaptor rpc-2.92 jack C mini-smp jack 02K118-K20D3 rosenberger hochfrequenztechnik gmbh & co. kg p.o.box 1260 d-84526 tittmoning germany www.rosenberger.de tel. : +49 8684 18-0 email : info@rosenberger.de page 3 / 3 rf_35/09.14/6.2 dieses dokument ist urheberrechtlich geschtzt this document is protected by copyright rosenberger hochfrequenztechnik gmbh & co. kg declaration of calibration options factory calibration standard delivery for this calibration standard inc ludes a factory calibration. the calibration certif icate issued reports individual calibration results, traceable to rosenberger standards , national / international standards are not available. model based standard d efinitions are reported in an agilent/keysight, rohde & schwarz and anritsu compatible vna format. accredited calibration not available. for further, more detailed information see applicat ion note an001 on the rosenberger homepage. calibration interval recommendation 12 months packing standard 1 pce in box weight 2.6 g/pce draft date approved date rev. engineering change n umber name date marcel panicke 03.11.09 markus mller 04.11.16 c00 16-1390 marion striegler 04.11.16 while the information has been carefully compiled t o the best of our knowledge, nothing is intended as representation or warr anty on our part and no statement herein shall be construed as recommendation to infringe existing patents. in the effort to improve our products, we reserve the right to make changes judg ed to be necessary.
|
