602 82 specifications are subject to change without notice ? 2002 teledyne relays 602\072002\q1 10a, 250vac optically isolated ac solid-state relay features ? available to desc drawing 86031-001 ? optical isolation ? low minimum output current ? extremely low emi ? zero voltage turn-on ? zero current turn-off ? logic compatible input ? available to y screening levels of mil-prf-28750 description the 602-1 is an ac output solid- state relay designed for power switching. the relay incorporates a hermetically sealed, optically coupled solid state relay as a driver. this driver provides zero voltage turn-on as well as a logic compatible control circuit. the relay output is rated for 10a at 250vac and switches the load with a hermetically sealed triac. a built- in snubber circuit provides reliable switching of both resistive and reactive loads with power factors as low as 0.2. the internal components are potted with a thermally conductive epoxy, which provides an environmental seal for severe environmental conditions encountered in military and aerospace applications. the 602-1 is available in w and y screening levels. the 602-1y is available to desc drawing 86031-001. series 602 part* desc drawing relay description number number 602-1W 10 a, 250 vac ac solid state relay 602-1y 86031-001 10 a, 250 vac ac solid state relay * the y suffix denotes parameters tested to mil-prf-28750 test methods. the w suffix denotes parameters tested to teledyne specifications. electrical specifications (-55 c to +95 c unless otherwise specified) input (control) characteristics min typ max units input current (see figure 1) v in = 5 vdc 15 ma dc v in =32 vdc 16 ma dc turn-off voltage (guaranteed off) 1.0 vdc turn-on voltage (guaranteed on) 3.8 vdc reverse voltage protection -32 vdc input voltage range 3.8 32 vdc output (load) specifications min typ max units output current range (see figure 3) 0.1 10 amps output voltage rating 25 250 vac frequency range 45 440 hz output voltage drop @ 10 amp (see figure 2) 1.5 vrms off-state leakage current 8.0 ma (250 vac, 400 hz) turn-on time 1/2 cycle turn-off time 1 cycle transient voltage (20 msec) +460 v pk overload current (16.6 msec) 100 amps zero voltage turn-on point +15 vpk dv/dt @ 25 o c (see note 4) 200 v/ s load power factor 0.2 insulation resistance @ 500 vdc 10 9 ohm input to output capacitance 15 pf wiring diagram
? 2002 teledyne relays (800) 284-7007 ? www.teledynerelays.com 602 83 602\072002\q1 series 602 mechanical specifications output (load) specifications min typ max units dielectric withstanding voltage 1500 vac junction temperature (t j max) 150 o c thermal resistance junction to ambient ( ja ) 15.5 o c/w thermal resistance junction to case ( jc ) 2.5 o c/w environmental specifications min typ max units ambient temperature operating -55 +95 o c storage -55 +110 o c shock for 6 ms 100 g vibration, 78 to 2000 hz 30 g (0.1 double amplitude 10 to 78 hz) acceleration 100 g notes: 1. unless otherwise specified, tolerances: .xxx = .005 (0.13mm); .xx = .01 (0.25mm). 2. weight: max. 3 oz. 3. built in snubber (r = 100 w c = 0.01mf). 4. output may lose blocking capabilities during and after surge until t j falls below maximum. 5. 100ms pulse @ 1 hz reptitive rate at 25 c, maximum 10 cycles. input current vs input voltage figure 1 load current vs typical output voltage drop figure 2 thermal derating curves figure 3 ? case material: self extinguishing plastic ? epoxy filled ? case color: black ? base plate material: aluminum ? circuit diagram shown on part is terminal view. dimensions are shown in inches (millimeters)
|
