series amepr10d-az up to 0.7a | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.p 1 of 4 north america only features: models single output model max output power (w) ? output voltage range (v) no load output voltage (v max.) output current (a) input voltage (vac/hz) efficiency (%) 115 vac 230 vac amepr10d-5020az +suffix ? exceeding the maximum output power w ill permanently damage the converter. model nomenclature for ordering: add suffix ?-ud? universal ac input 90-264vac ( no triac dimming option), ip20 add suffix ?-uw? universal ac input 90-264vac (no triac dimming option), ip67 add suffix ?-110d? ac input 90-135vac, ip20 add suffix ?-110w? ac input 90-135vac, ip67 add suffix ?-220d? ac input 180-264vac, ip20 add suffix ?-220w? ac input 180-264vac, ip67 note: aimtec limited warranty of 5 years is valid based on product operation at datashee t specifications at ambient temperature of 25c, humidity<75%, nominal input voltage (115/230vac) and at rated output load unless otherwise specified. see http://www.aimtec.com/terms- sale amepr10d-az?s ac/dc led drivers have electrical safeguards design ed within to protect it from conventional electrical abnormali ties with the levels listed in the safety table. a pplications for use within rural agricultura l, heavy industrial, and other areas or re gions which are prone to ?dirty? electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. in this case consideratio n should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of aimtec device to ensure t he longevity of the products. failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. input specifications parameters conditions typical maximum units inrush current <2ms (cold start) 115vac 15 a 230vac 25 leakage current 115vac 0.2 ma 230vac 0.25 current (full load) 115vac 110 ma 230vac 55 power factor 115vac 0.9 230vac 0.9 external fuse (slow blow) recommended slow blow type 1 a start up time 200 ms ? ac-dc constant current led driver ? ? input range 90-264vac/47-440hz ? ? high efficiency up to 81% ? ? operating temperature -20 to 80c ? total harmonic distortion < 20% ? 5 year limited warranty ? ? leading or trailing edge triac click on series name for product info on aimtec.com
series amepr10d-az up to 0.7a | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.p 2 of 4 north america only output specifications parameters conditions typical maximum units current accuracy 7 % line regulation (ll-hl) 10 % load regulation 0-100% load 7 % ripple & noise 3 v p-p hold-up time 1 ms minimum load voltage see the models table ripple and noise are measured at 20mhz bandwidth by using a 0.1 f (m/c) or (c/c) and 47f (e/c) parallel capacitor. isolation specifications parameters conditions typical maximum units tested i/o voltage 60 sec 3000 vac isolation resistance >1000 m ? general specifications parameters conditions typical maximum units switching frequency 65 khz over load protection 110 % over voltage protection 110 % short circuit protection auto recovery over temperature protection >105c operating temperature with derating over 55c (for ip67 case) -20 to +80 o c maximum case temperature 100 o c storage temperature -40 to +95 o c temperature coefficient 0.02 % / o c cooling free air convection humidity 95 % rh case material plastic wires ul1015 input 18awg*10cm/ output 20 awg * 10cm weight ip20 160 g ip67 200 dimensions (l x h x w) 133 x 33 x 30mm (5.24 x 1.30 x 1.18 inch) mtbf >400,000 hrs (mil-hdbk-217f at +25c) environment approval test parameters conditions shock wave form half sine wave acceleration amplitude 5gn bump duration 30 ms converter operation before and after test, body mounted (on chassis) number of bumps 18 (3 in each direction for every axis) vibration test mode sweep sine, 10-100hz, speed 0.05hz/s displacement 1 mm acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis)
series amepr10d-az up to 0.7a | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.p 3 of 4 north america only safety specifications parameters agency approvals culus, ce, fcc standards en61347-1, en61347-2-13, iec62384, ul8750, ul60950-1, en55015, en55024, fcc part 15 subpart b, class b, ansi c63.4 :2003 harmonic current emissions iec/en 61000-3-2, class c voltage fluctuations and flicker iec/en 61000-3-3, (en60555-3) electrostatic discharge immunity iec 61000-4-2 level 3 rf, electromagnetic field immunity iec 61000-4-3 level 2 electrical fast transient/burst immunity iec 61000-4-4 level 2 surge immunity iec 61000-4-5 level 1 rf, conducted disturbance immunity iec 61000-4-6 level 2 power frequency magnetic field immunity iec 61000-4-8 level 2 voltage dips, short interruptions immunity iec 61000-4-11 dimensions
series amepr10d-az up to 0.7a | ac-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.p 4 of 4 north america only temperature graph triac dimming feature ac earth ? ground line ? (brown) neutral ? (blue) triac ? device aimtec led ? driver red ? (+) black ? (-) led ? lighting ? application triac ? dimming ? notes: a- the ? triac ? device ? can ? be ? installed ? on ? either ? line ? or ? neutral b- aimtec ? led ? drivers ? have ? been ? designed ? to ? function ? with ? a ? wide ? range ? of ? available ? triac ? devices, ? however ? the ? following ? list ? of ? triac ? devices ? have ? been ? tested. 1) ? company: ? lutron series: ? skylark model: ? sf-10p-wh ? (input ? voltage: ? 120vac) model: ? sf-12p-277-wh ? (input ? voltage ? 277vac) 2) ? company ? lutron series: ? diva model: ? dvf-103p-wh ? (input ? voltage: ? 120vac) model: ? dvf-103p-277-wh ? (input ? voltage: ? 277vac) 3) ? company ? berker model: ? 2867 ? 10 ? (input ? voltage:230vac) if ? the ? power ? voltage ? range ? is ? 90~135vac, ? triac ? suggested ? use ? model ? sf-10p-wh ? or ? dvf-103p-wh. if ? the ? power ? voltage ? range ? is ? 180~260vac, ? triac ? suggested ? use ? model ? sf-12p-277-wh ? or ? dvf-103p-277-wh. note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. .aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 5. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet.
|
