spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 1 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108 t-1 3/4 (5mm) solid state lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: wp7083qbd/d blue features z outstanding material efficiency. z reliable and rugged. z rohs compliant. descriptions z the blue source color devices are made with ingan light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. lead spacing is measured where the leads emerge from the package. 4. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 2 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. 3. luminous intensity value is traceable to cie127-2007 standards. absolute maximum ratings at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to cie127-2007 standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. part no. emitting color (material) lens type v iewing angle [1] min. typ. 2 1/2 wp7083qbd/d blue (ingan) blue diffused 120 250 60 iv (mcd) [2] @ 20ma symbol parameter emitting color typ. max. units test conditions peak peak wavelength blue 460 nm i f =20ma d [1] dominant wavelength blue 465 nm i f =20ma ? 1/2 spectral line half-width blue 25 nm i f =20ma c capacitance blue 100 pf v f =0v;f=1mhz v f [2] forward voltage blue 3.3 4 v i f =20ma i r reverse current blue 50 ua v r = 5v parameter values units power dissipation 120 mw dc forward current 30 ma peak forward current [1] 150 ma reverse voltage 5 v operating/storage temperature -40c to +85c lead solder temperature [2] 260c for 3 seconds lead solder temperature [3] 260c for 5 seconds electrostatic dischar ge threshold (hbm) 250 v notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. 2mm below package base. 3. 5mm below package base. 4. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static electricity ? ref jedec/jesd625-a and jedec/j-std-033. electrical / optical characteristics at ta=25c
spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 3 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108 blue wp7083qbd/d
spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 4 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108 packing & label specifications wp7083qbd/d terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 5 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108
spec no: dsah9250 rev no: v.6b date: jan/23/2017 page: 6 of 6 approved: wynec checked: allen liu drawn: l.t.zhang er p: 1101013108
|
