View SGM3142YTQE16GTR_9054222.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sgm 3142 6- channel charge pump white led driver with low dropout current source g eneral d escription the sgm 3142 is a high efficiency and cost effective charge pump white led driver. it supports up to 6 white leds and regulates a constant current for uniform intensity. the part maintains the high efficiency by utilizing a 1/1.5 fractional charge pump and low dropout current sources. the small equivalent 1 mode open loop resistance and ultra - low dropout voltage of current source extend the operating time of 1 mode and optimize the efficiency of li - ion battery in white led applications. user can easily configure each led current from 1.25ma to 20 ma by a pulse dimming control. the dimming of white leds current can be achieved by applying a pulse s ignal to the en /set pin. there are totally 16 steps of current could be set by users. the operating voltage range is 2. 7 v to 5. 5 v. internal soft - start circuitry effectively reduces the in - rush current while both start - up and mode transition. the sgm3142 i s available in green tqfn -44- 16l package and is specified over an ambient temperature range of - 40 to +85 . features input voltage range: 2.7v to 5.5v drives up to 6 leds at 20 ma each 16 -s tep brightness c ontrol high efficiency by fractional conversion w ith 1 and 1.5 modes automatic charge pump mode selection switching frequency: 1mhz 1% typical led current matching internal soft -s tart limits inrush current low input noise and low emi over -c urrent and over -t emperature p rotection output over - voltage prot ection under -v oltage lockout w ith hysteresis available in green tqfn -44- 16l package a pplications white led backlighting white photo - flash for dscs color (rgb) lighting programmable current source rev. a . 2 sg micro corp www.sg - micro.com a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 2 sgm 3142 sg micro corp www.sg - micro.com package/ordering information model order nu mber package description specified temperature range package option marking information sgm3142 sgm3142 ytqe 16g /tr tqfn -44- 16l -40 to +85 tape and reel, 3000 sgm3142ytq e16 absolute maximum ratings vin to gnd ........................................................ - 0.3v to 6.0v the other pins to gnd ... .. - 0.3v to 6.0v package thermal resistance tqfn -44-16 l, ja . .. ...50 /w storage temperature range... . ... ....- 65 to + 150 junction temperature ................................................... 150 operating temperature range... ...-40 to + 85 lead temperature (soldering 10 sec) .. .................................................................................... 260 esd susceptibility hbm .. 2 000 v mm. ..3 00 v note: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. these are stress ratings only, and functional operation of the device at these or any other conditions beyo nd those indicated in the operational sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. caution this integrated circuit can be damaged by esd if you dont pay attention to esd protection. sgmicro recommends that all integrated circuits be handled with appropriate precautions. failure to observe proper handling and installation procedures can cause damage. esd damage can range from subtle performance degradation to complete device failure. precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. sgmicro reserves the right to make any change in circuit de sign, specification or other related things if necessary without notice at any time. please contact sgmicro sales office to get the last datasheet. a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 3 sgm 3142 sg micro corp www.sg - micro.com pin configuration (top view) c2p vout c2n gnd 10 vin led 4 5 6 7 8 2 3 4 1 9 11 12 13 14 15 16 c1p c1n n.c. n.c. en/ set led 1 led 5 led 2 led 3 led 6 gnd tqfn -44- 16 l pin description pin name function 16 led1 output current for led 1 . 1 led 2 output current for led 2 . 2 led5 output current for led 5. 3 led6 output current for led 6. 4 led3 output current for led3. 5 led4 output current for led 4. 6 c1p positive i nput for the e xternal f lying c apacitor c1 . connect a ceramic 1f capacitor close to the pins of the ic. 7 c1n negative i nput for the e xternal f lying c apacitor c1 . connect a ceramic 1f capacitor close to the pins of the ic. 8,13 n.c. no internal connection. 9 vout output voltage source. 10 c2p positive i nput for the e xternal f lying c apacitor c2 . connect a ceramic 1f capacitor close to the pins of the ic. 11 c2n negative i nput f or the e xternal f lying c apacitor c2 . connect a ceramic 1f capacitor close to the pins of the ic. 12 gnd ground. 14 vin power input voltage. 15 en/set chip enable (active high) and dimming control. exposed pad gnd exposed pad should be soldered to pcb board and connected to gnd. a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 4 sgm 3142 sg micro corp www.sg - micro.com electrical characteristics (v in = 2. 7 v to 5.5v, c in = c out = c1 = c2 = 1f, t a = + 25 , unless otherwise noted. ) parameter symbol conditions min typ max units input power supply input supply voltage v in 2.7 5.5 v under -v oltage lockout threshold v in rising 1.8 2.2 2.5 v under -v oltage lockout hysteresis 100 mv quiescent power supply current i q 1 mode, v in = 4v 0.3 1 ma i q 1.5 mode, v in = 3.3v 1 3.5 shutdown current i shdn v en = 0.4v 0.1 10 a 1 mode to 1.5 mode transition voltage (v in falling) v ts_1.5 v f = 3. 2 5v, i out = 120 ma, i ledx = 20ma 3.68 v hysteresis of mode transition 350 mv output output current i ledx v in = 3.5v,100% setting 18 20 22 ma current matching v in = 3.5v,100% setting -4 1 4 % en /set logic threshold logic - high voltage v ih 1.5 v logic - low voltage v il 0.4 v low time for dimming t lo 0.5 75 s high time for dimming t hi 0.25 s en/set current high current i ih v ih = v in 0.01 1 a low current i il v il = gnd 0.01 1 a low time for shutdown t shdn pwm dimming 0.3 0.5 ms frequency oscillator frequency f osc 1000 khz a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 5 sgm 3142 sg micro corp www.sg - micro.com typical performance characteristics c in = c out = c1 = c2 = 1f, t a = +25 , unless otherwise noted. efficiency vs. input voltage (620ma) 40 50 60 70 80 90 100 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 input voltage (v) efficiency (%) v diode = 3.25v efficiency vs. input voltage (610ma) 40 50 60 70 80 90 100 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 input voltage (v) efficiency (%) v diode = 3.1v a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 6 sgm 3142 sg micro corp www.sg - micro.com typical performance characteristics c in = c out = c1 = c2 = 1 f, t a = +25 , unless otherwise noted. i diode vs. input voltage (620ma) 100 105 110 115 120 125 130 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 input voltage (v) i diode (ma) v diode = 3.25v enable voltage vs. input voltage 0.4 0.6 0.8 1.0 1.2 1.4 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 input voltage (v) en voltage threshold (v) rising falling i diode vs. input voltage (610ma) 50 55 60 65 70 75 80 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 input voltage (v) i diode (ma) v diode = 3.1v a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 7 sgm 3142 sg micro corp www.sg - micro.com function block diagr am 1/1.5 c harge pump c1p c1n c2p c2n led1 led2 led3 led4 led driver en/set 1 mhz osc voltage reference vout soft start control vin current reference led6 led5 16 steps pulse dimming interface uvlo ovp dimming dac a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 8 sgm 3142 sg micro corp www.sg - micro.com t ypical application + c in 1 f led 4 led 3 led 2 led 1 c1n c2p c1p c2n sgm 3142 vin en/ set gnd v battery 15 12 led 5 led 6 vout c out 1 f 16 1 4 5 2 3 14 9 c1 1f c2 1f 6 7 10 11 en / set figure 1. for 6- wleds application circuit en i ledx shutdown 100 % 15 / 16 3/ 16 4/ 16 5/ 16 1/ 16 s hutdown 0 1 2 3 4 5 14 15 0 1 30 s < t ready 0.5s < t hi 0.5s < t lo < 75 s 500 s < t shdn 2/ 16 2/ 16 1/ 16 figure 2 . brightness c ontrol by p ulse d imming a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 9 sgm 3142 sg micro corp www.sg - micro.com typical application circuits + c in 1 f led 4 led 3 led 2 led 1 c1n c2p c1p c2n sgm 3142 vin en/ set gnd v battery 15 12 led 5 led 6 vout c out 1 f 14 9 c1 1f c2 1f 6 7 10 11 en/ set 16 1 4 5 2 3 r b r b r b resistor r is optional r b r b r b resistor r is optional figu re 3 . driving two groups of paralleled white led's + c in 1 f led 4 led 3 led 2 led 1 c1n c2p c1p c2n sgm 3142 vin en/ set gnd v battery 15 12 led 5 led 6 vout c out 1 f 14 9 c1 1f c2 1f 6 7 10 11 en/ set 16 1 4 5 2 3 r b r b r b resistor r is optional r b r b r b photo flash led in some applications, white led forward voltages (v f ) can vary significantly. ballast resistors between the led cathodes and ground are recommended for balancing the forward voltage differences. the ballast resistor value may be approximated by the following equation: f f source b i v v r ? = figure 4 . driving high current photo - flash led a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 10 sgm 3142 sg micro corp www.sg - micro.com application information the sgm 3142 is a high efficiency charge pump white led driver. it provides 6 channels low dropout voltage current source to regulated 6 white leds current. for high efficiency, the sgm 3142 implements a smart mode transition for charge pump operation. the sgm 3142 provides pulse dimming function for led brightness control. soft - start the sgm 3142 includes a soft - start circuit to limit the inrush current at power on and mode switching. soft - start circuit limits the input current before output voltage reaching a desired voltage level. input uvlo the input operating voltage range of the sgm 3142 is 2.7v to 5.5v. an input capacitor at the vin pin could reduce ripple voltage. it is recommended to use a ceramic 1f or larger capacitance as the input capacitor. this ic provides an under - voltage lockout (uvlo) function to prevent it from unstable issue when startup. the uvlo threshold of input rising voltage is set at 2. 2v typically with a hysteresis 100 mv. thermal protection the sgm3142 has a thermal protection circuit that will shut down the internal ldo and charge pump if the die temperatur e rises above the thermal limit . mode decision the sgm 3142 uses a smart mode selection method to decide the working mode for optimizing the efficiency. mode decision circuit senses the output and led voltage for up/down selection. the sgm 3142 automatically switches to 1.5 mode whenever the dropout condition is d etected from the current source and returns to 1 mode whenever the dropout condition releases. brightness control the sgm 3142 implements the pulse dimming method being used to control the brightness of white leds. the part implements a 4 - bit dac for brightness control. users can easily configure the led current from 1.25ma to 2 0ma by a serial pulse. the maximum led current is up to 2 0ma that is sufficient for most application in backlight. the dimming of white leds' current can be achieved by applying a pulse signal to the en /set pin. there are totally 16 steps of current could be set by users. the detail operation of brightness dimming is showed in the figure 2. selecting capacitors careful selection of the four external capacitors c in , c1, c2, c out is important because they will affect some parameters such as input and output ripple, power efficiency, maximum supply current by charge pump, and start - up time. to reduce the input and output ripple effectively, the low esr ceramic capacitors are recommend ed. generally, to reduce the output ripple, increasing the output capacitance c out is necessary. however, this will increase the startup time of output voltage. for led driver applications, the input voltage ripple is more important than output ripple. inp ut ripple is controlled by input capacitor c in , increasing the value of input capacitance can further reduce the ripple. practically, the input voltage ripple depends on the power supplys impedance. if a single input capacitor c in cannot satisfy the requirement of application, it is necessary to add a low - pass filter. c -r- c filter used to reduce input ripple. the flying capacitor c1 and c2 determine the supply current capability of the charge pump. the lower value will limit the led s current at low input voltage . for 6 20ma load over the entire input range of 2.7v to 5.5v, it is recommended to use a 1f ceramic capacitor on the flying capacitor c1 and c2. a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 11 sgm 3142 sg micro corp www.sg - micro.com application information driving multiple led's, white led d isplay m odule b ack l ights the sgm3142 led1 to led6 outputs are true constant current sources capable of driving up to 20ma each over the operation input voltage range. since these outputs are true constant current sources, they may be connected in parallel to drive a single power output. any combination of outputs (led1 to led6) may be connected in parallel. the maximum total output current is a sum of how many current sources are parallel connected. this feature is particularly useful to power pre - manufactured display modules which are pr e- wired with white led backlights connected in a parallel circuit configuration. any combination of outputs may be connected in parallel to drive groups of led's. the sgm3142 internal current source reference circuit bases feedback from current sensed on the led1 and led5 outputs. for best operation, the only requirement for this type of application is the output led1 and led5 should always be connected to the load circuit. the sgm3142 may be used to drive multiple led's having differing forward voltages. using feedback techniques, the current in led1 to led4 output currents sources are referenced to the current i n the led connected to led1 . the led5 and led6 output current sources are referenced to the current in led5, not to led1. if all six led's are of similar type, the diodes will be matched in current, maintaining uniform led brightness despite variations in manufacturer, production, etc. a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 12 sgm 3142 sg micro corp www.sg - micro.com package outline dimensions tqfn -44- 16l recommended land pattern (unit: mm) n9 k e1 e e n16 n5 n1 d d1 l b a1 a2 a side view bottom view top view 0.3 0.65 2.1 2.9 4.6 0.85 2.1 symbol dimensions in millimeters dimensions in inches min max min max a 0.700 0.800 0.028 0.031 a1 0.000 0.050 0.000 0.002 a2 0.203 ref 0.008 ref d 3.900 4.100 0.154 0.161 d1 2.000 2.200 0.079 0.087 e 3.900 4.100 0.154 0.161 e1 2.000 2.200 0.079 0.087 k 0.200 min 0.008 min b 0.250 0.350 0.010 0.014 e 0.650 typ 0.026 typ l 0.450 0.650 0.018 0.026 a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 13 sgm 3142 sg micro corp www.sg - micro.com tape and reel information note: the picture is only for reference. please make the object as the standard. key parameter list of tape and reel package type reel diameter reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p0 (mm) p1 (mm) p2 (mm) w (mm) pin1 quadrant tqfn - 44 -16l 13 12.4 4.3 4.3 1.1 4.0 8.0 2.0 12.0 q1 reel width (w1) reel diameter reel dimensions tape dimensions direction of feed p2 p0 w p1 a0 k0 b0 q1 q2 q4 q3 q3 q4 q2 q1 q3 q4 q2 q1 a ll data sheet.com
6- channel charge pump white led driver with low dropout current source 14 sgm 3142 sg micro corp www.sg - micro.com carton box dimensions note: the picture is only for reference. please make the object as the st andard. key parameter list of carton box reel type length (mm) width (mm) height (mm) pizza/carton 13 38 6 280 370 5 a ll data sheet.com

▲Up To Search▲

Price & Availability of SGM3142YTQE16GTR

	To Download SGM3142YTQE16GTR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .