p ? design and speciications are subject to change without notice. ask the factory for technical speciic ations before purchase and/or use. if there is any doubt regarding the safety of this product, kindly inform us immediately for technical consultation. pan1555 rev. b1 www.pedeu.panasonic.d e wireless@eu.panasonic.com w ireless m odules panasonic electronic devices europe gmbh now you can integrate bluetooth very easy in your inal product, without qualiication C with the pan1555. this solution follows the national and international regulations, e.g. ce (radio, emc, safety), fcc and ic. the pan1555 is manufactured in a 13.50 x 22.75 x 2.85 mm3 smd package with an integrated ceramic antenna or plug and will be qualiied as a bluetooth 2.0 product. re-qualiication of your product is usually not required. this is why the pan1555 is particularly suited for units produced in smaller or medium quantities. this module is a one to one replacement for the well known pan1550. any customizations for the software can be handled with our recommended partners. general - complete bluetooth 2.0 + edr solution - full product qualiication (bluetooth, ce, fcc, ic) - proiles: gap, sdap, spp, hid and hdp available, other could be supported on request. - csr bluecore6-rom inside - cortex-m3 st32f103 core for embedded proiles or application software - temperature range from -40c to +85c - supply voltage range from 2.7v to 3.6v, typ. 3.3v - fast connection setup - support for 802.11 coexistence interfaces - uart (programmable baud rate), usb, i2c, spi and adc - 18 gpios for individual usage for your embedded software - all bluetooth data rate up to 2178kbps asymmetric - pcm interface master / slave supporting 13 or 16 bit linear, 8 bit -law or a-law codecs and cvsd transcoders on up to 3 sco channels. bluetooth - high sensitivity design (typ. -86 dbm) - full 8- to 128-bit encryption - power control and rssi, hold-, park- and sniffmode - support for very low power modes - sleep and deep sleep outlines - enw89815a3kf features bluetooth v2.0 embedded pan1555-emb-2.0 cut the cable tm hardware status: mass production downloaded from: http:///
p ? www.pedeu.panasonic.d e wireless@eu.panasonic.com contact dipl.-ing. ingo wagner product engineer module business panasonic electronic devices europe gmbh zeppelinstrasse 19 21337 lneburg, germany tel. (49)-4131-899-173 fax (49)-4131-899-177 ingo.wagner@eu.panasonic.com parameter value condition / note receiver sensitivity (ber=10 -3 ) -86 dbm typ. ideal wanted signal output power +4 dbm typ. power supply 2,7 - 3,6 v single operation voltage ultra low power mode <100 a t = 25c acl (connected dh5) 50.5ma to 49.5ma max. power to min. power (1) acl (connected dh1) 48.0ma to 46.0ma max. power to min. power (1) operating temperature range -40c to +85c storage until +125c (1) figure indicates to the shortest poll period and to the slave mode all embedded wireless applications- printer adapters - printers - access points - wireless sensors - industrial applications - cable replacement - personal digital assistants (pdas) - personal navigation devices - medical applications block-diagram technical characteristics applications ????? ?????????????? ??????????? ????? ??????? ?????????? ??????????? ????? ?????? ??????? ?????????? ???????? ??????????? ???????? ??????????????????? ???????? ????? ??? ??? ????????????? ??????????? ?????????? ????????????? ??????? ??????? ???????? ?????????????? ????????? ????????? ????? ?????? ??????????? ????? ????? ??????????? ?????? ???? ????? ???? ?????? hardware status: mass production downloaded from: http:///
|
